GEM DG 800 Manuale utente

ACCESS CONTROL

OPTIONS

KT-15EM KT-16 621-11STD-PCPSSTD-PC KT-10BC

−

N.C.1

COM 1

N.O.1

PB1

PB2

REED

N.C.2

COM 2

N.O.2

GND

Electric Lock 1

(Fail-Safe)

Electric Lock 2

(Fail-Secure)

12VDC

Power

Supply

(MUST install a Diode)

(MUST install a Varistor)

Varistor

Diode

Door Closed=N.O.

Door Opened=N.C.

Exit Button 1

Exit Button 2

REED

12VDC

Power

Supply

▲

Stand Alone Reader

For AC/DC

For DC

use only

RED +PINK COM. 1 YELLOW PB2 PURPLE COM.2

BLACK

WHITE N.O.1 BROWN REED BLUE N.O.2

LIGHT

GREEN N.C.1 ORANGE PB1 GREY N.C.2 GREEN GND

120

DG 800

Combined Proximity

and Keypad Access

• Operating voltage 12~24Vac/Vdc

• Die-cast Aluminium

• 1000+10 Proximity cards, tokens and PIN’s

• Backlit keypad

• Weather resistant: IP65

• Vandal resistant

• 2 LED displays with audible indication

WEATHER

RESISTANT

− IP 65 −

VANDAL

RESISTANT

All dimensions in mm

42 Access Control

1. Memory volume up to 1000+10 proximity cards/tokens and PINs. Reading time

approx. 0.5 seconds.

2. Access modes:

a. Only Proximity Card

b. PIN or Proximity Card (default setting)

c. PIN + Proximity Card

3. Logical memory prevents duplicated card setting.

4. Lockout Function: The controller will lockout for 60 seconds after entering

invalid PINs or reading invalid cards for 5 times. (The keypad doesn’t beep

during the period of time).

5. Controller with keypad sound to avoid incorrect key-in.

6. Additional input for anti-tailgating function to ensure high security access

control.

7. Built-in anti-tamper switch.

8. Non-volatile memory stores all code settings, even in the event of total power

failure or controller not in use for a long time.

9. Dual relays to control door lock and other security devices.

10. Aluminum alloy casing with vandal resistant screws for enhanced safety and

durability.

11. Epoxy sealed for waterproof.

12. Slim-type keypad design for narrow door-frames (DG-160).

EM 125KHz

5 cm (In noise-free environment)

Backlight 12-digit (0~9,＊,#)

Relay Rating

All LEDs Stay On

Right Green Stay On

Red Stay On

Valid card, press key, enter programming mode

Diode

12~24VAC/DC

DG-160: Pull In:60mA/12VDC,Holding:40mA/12VDC

Pull In:30mA/24VDC,Holding:20mA/24VDC

DG-800: Pull In:100mA/12VDC,Holding:70mA/12VDC

Pull In:50mA/24VDC,Holding:35mA/24VDC

Max.2A/30VDC ; 0.6A/120VAC

1234 (4 digits)

Master Code

Relay Strike Time (Time Delay Setting)

Pressed Key Time Delay

PIN Code Input Waiting Time

Programming Mode Time Delay

Card Storage (MAX. 1000+10pcs)

Format

Access Mode PIN or Proximity Card

All Bits

None

1 second

5 seconds (Fixed)

5 seconds

30 seconds (Fixed)

2. Read new card (1 beep), then press 4-digit PIN 9999 (1 beep, Right Yellow

LED stay on).

3. Press # (1 beep) back to standby mode (Right Green LED stay on)

Enter the master code twice (1234 1234) to enter programming mode (1 long

beep, Right Yellow LED stay on).

The dual identification feature allows the reader to be programmed to grant access

with either Proximity Card only, Proximity Card or PIN, Proximity Card and PIN.

1. Enter programming mode

2. Press*0 (Right Yellow LED rapid flash)

3. Press 00 (1 beep,Right Yellow LED stay on) for Proximity Card Only

Press 01 (1 beep,Right Yellow LED stay on) for Proximity Card or PIN

Press 02 (1 beep,Right Yellow LED stay on) for Proximity Card + PIN

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

The relay strike time determines the amount of time that the door remains

unlocked after a valid proximity card or PIN is entered.

1. Enter programming mode

2. Press *1 for Relay 1 (Right Yellow LED rapid flash)

Press *5 for Relay 2 (Right Yellow LED rapid flash)

3. Press 00~99 (1 beep,Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

1. Enter programming mode

2. Press * 8 (Right Yellow LED rapid flash)

3. Press 88 (No LED , 1 long beep, right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Ridht Green LED stay on)

1. Enter programming mode

2. Enter *8 (Right Yellow LED rapid flash)

3. Enter 99 (Both left & rigth Yellow LEDs stay on, 1 beep) back to standby mode

(Right Green LED stay on)

a.1. Enter programming mode to select slot position 000~999 (Left Green LED

stay on, Right Yellow LED rapid flash to indicate the slot position is available)

b. 1. Enter programming mode to select slot position 000~999 (Left Red LED stay

on, Right Yellow LED rapid flash to indicate the slot position is unavailable)

2. Press * * (1 beep) to delete the data from the slot position (Left Green LED

stay on, Right Yellow LED rapid flash)

3. Press # , back to satndby mode

4. Repeat the steps of 7-a to add new cards.

a. 1. Enter programming mode

2. Press * 4 to select slot position 00~09 (Left Green LED stay on , Right Yellow

LED rapid flash to indicate the slot position is available)

3. Read new card (1 beep, Right Yellow LED flash)

4. Press # (1 Beep) back to programming mode (Right Yellow LED flash)

5. Press # (1 Beep) , back to satndby mode

b. 1. Enter programming mode

2. Press * 4 to select slot position 00~09 (Left Red LED stay on , Right Yellow

LED rapid flash to indicate the slot position is unavailable)

3. Press * * to delete the data from the slot position (1 beep, Left Green LED

stay on, Right Yellow LED rapid flash)

4. Press # , back to satndby mode

5. Repeat the steps of 8-a to add new cards.

1. Enter programming mode

2. Press * 3 (Right Yellow LED rapid flash)

3. Enter 4-digit master code twice e.g. 4567 4567 (1 beep, Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

a. 1. Enter programming mode

2. Press * 7 (Left Green LED rapid flash, Right Yellow LED rapid flash to

indicate the slot position is available)

3. Read new card to set as Master Card (1 beep, Right Yellow LED stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

b. 1. Enter programming mode

2. Press * 7 (Left Green LED stay on , Right Yellow LED rapid flash to indicate

the Master Card had been stored)

3. Press* * to delete the data (1 beep, Left Green LED rapid flash, Right Yellow LED

rapid flash)

4. Press # , back to satndby mode

5. Repeat the steps of 10-a to add new master card.

a. 1. Read master card once (1 beep, Right Yellow LED stay on)

2. Enter slot position 000~999 (Left Green LED stay on, Right Yellow LED rapid

flash to indicate the slot position is available)

3. Read new card (1 beep), then enter 4-digit PIN 9999 (1 beep, Right Yellow LED

stay on)

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

b. 1. Read master card once (1 beep, Right Yellow LED stay on)

2. Enter slot position 000~999 (Left Red LED stay on, Right Yellow LED rapid

flash to indicate the slot position is unavailable)

3. Press * * to delete the data from the slot position (1 beep, Left Green LED

stay on, Right Yellow LED rapid flash)

4. Repeat the steps of 11-a to add new cards.

1. Enter programming mode

2. Press * 6 (Right Yellow LED rapid flash)

3. Press 01 ( 1 beep, Right Yellow LED stay on) - function OFF

Press 02 ( 1 beep, Right Yellow LED stay on) - function ON

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

1. Enter programming mode

2. Press * 2 (Right Yellow LED rapid flash)

3. Press 01 (1 beep, Right Yellow LED stay on) - function OFF

Press 02 (1 beep, Right Yellow LED stay on) - function ON

4. Press # (1 beep) back to standby mode (Right Green LED stay on)

Note: Turning on doorbell alarm function on the second relay, relay

strike time is 1 second.

Turn off the power: press # continuously, and energize (1 beep), the master code

is reset to default value.

The master code consists of a four-digit number and is used to access

programming functions of the reader and cannot be used to gain access i.e. It

cannot be the same as other PINs. The default master code is set as 1234. Under

normal operation the keypad is used for entering PIN to gain access. In the

programming mode the keypad can be used to add/delete PINs, set relay strike

time and other operation functions.

15. Add new cards to Relay 1

1. Enter programming mode, press *9 (Right Yellow LED flash)

2. Press 01 (1 beep, right Yellow LED flash)

3. Select slot position 000~999, press the number of cards (001~999) (1 beep,

right Yellow LED flash)

4. Read new cards (in serial order) (1 beep, right Yellow LED flash)

5. Press # (1 beep) back to standby mode (right Green LED stay on)

16. Change PIN to Relay 1

1. Enter programming mode, press *9 (right Yellow LED flash)

2. Press 02 (1 beep, right Yellow LED flash)

3. Press slot position 000~999

4. Press PIN code (1 beep, right Yellow LED flash)

5. Press # (1 beep) back to programming mode (right Yellow LED stay on)

6. Press # (1 beep) back to standby mode (right Green LED stay on)

17. Change the length of Master Code

1. Enter programming mode, press *9 (right Yellow LED flash)

2. Press 04 (1 beep, right Yellow flash)

3. Press the length of Master Code (4 ~ 6 digits) (beep…clear PINs and cards)

(1 beep)

4. back to programming mode (right Yellow LED stay on)

5. Press # (1 beep) back to standby mode (right Green LED stay on)

(After changing the length of Master Code, all PINs and cards will be cleared

too. If the length of Master Code is 4 digits, press 1234; if 5 digits, press 12345;

if 6 digits, press 123456.)

14. Reset the Master Code to Default Value

13. Turn Doorbell Alarm Function ON/OFF

12. Turn Anti-Tamper Alarm Function ON/OFF

11. Add New Cards by Master Card

10. Add a New Master Card to Relay 1

9. Change Master Code

8. Add a Proximity Card and PIN to Relay 2

7. Add a Proximity Card and PIN to Relay 1

6. Reset Controller Parameter to Default Value

5. Clear Memory of All Proximity Cards and PINs

4. Set the Relay Strike Time

3. Set the Access Mode

2. Enter Programming Mode

1. Master Code

Questo manuale è adatto per i seguenti modelli

Altri manuali GEM Lettore di schede

GEM

GEM EASIPROX-ANSI Manuale tecnico

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente