General Lock CX480-DN Manuale utente
CX480-DN Users Manual and Installation Instructions
CX480-DN Day/Night Camera
Users Manual and
Installation Instructions
1. Do not expose the camera to humidity and dust.
Moisture can damage the camera and cause the danger of electric shock. If the camera is
mounted outdoors, a camera housing is required. Do not install the camera at where there is
greasy smoke or steam, where the humidity is too high, or where there is a lot of dust to
prevent damages to the camera.
2. Do not disassemble the camera.
Do not disassemble the camera body as it is dangerous and may cause the damages to the
camera. Refer all servicing to qualified service personnel.
3. Handle the camera with care.
Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to
prevent any damages to it.
4. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers because the magnetic fields generate from above devices will distort the video
image.
Safet
y
Warnin
g
5. Never face the camera toward the sun.
Never aim the camera at the sun or other extremely bright objects whether it is in use or not.
6. Do not install the camera in the high temperature environment.
Installed the camera away from stoves, or other heat generating devices, or where it could be
subject to direct sunlight as the high temperatures could cause deformation, discoloration or
other damages of the camera. Install the camera at where the temperature range will stay
between 0℃to 50℃(32℉to 122℉).
7. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use a soft cloth to remove the dirt
from the camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean the
CCD sensor and the camera lens. When the camera is not in use, put the cover cap on the
lens mount.
The Day/Night Digital Color Camera introduces a new level of high quality picture. The
compact, full performance, general-purpose color DSP Cameras, which use high sensitive
1/3"interline transfer Super HAD CCDs (Charge Coupled Device). It delivers
high-resolution superior color images in bright light, and clear sharp monochrome pictures
in low light. The evolution 2-in1 intelligent video camera brings your security
surveillance system to a new digital era.
Main Features
1/3” color CCD pick up device.
480 lines of horizontal resolution.
Signal-to-noise ratio more than 48 dB.
Minimum illumination of 1.0 lux with F=1.2 lens.
Programmable camera ID up to 9 characters.
High resolution color camera in normal light; black and white camera in low light.
User friendly on-screen set up menu allows ES, AGC, AWB, BLC, and Sync. Phase
to be customized program.
Selectable exposure modes including: ES, Manual Exposure, Flickerless, and Auto
IRIS.
RS232 remote control communication and S-Video output available.
CX480-DN Introduction
Pickup device: 1/3” interline transfer color CCD
Video format: NTSC/PAL
Scanning system: NTSC:525 lines, PAL:625 lines
Picture elements: NTSC:768 (H) x 494 (V) ; PAL: 752(H) x 582(V)
Horizontal resolution: 480 TV lines
Sensitivity: 1.0 lux / F=1.2
S/N ratio: > 48 dB
Camera ID symbol: 9 characters title generator
Back light comp.: Yes, 255 levels variables on screen
Auto white balance: 3 Modes selectable cStandard: 2500°K~9500°K; dLarge Frame: 2400°K~11000°K;
eFrameless: 2000°K~18000°K
Auto white balance speed: 15 steps variables on screen
Auto IRIS: Video Drive or Direct Drive switchable
D/D lens iris level: Level: 150 steps variables on screen
Exposure: 4 modes selectable on screen
cES: 1/60(1/50) ~ 1/100000 sec.; AGC Gain: 10~36 dB
dManual Exposure: 1/60(1/50), 1/100(1/120), 1/250, 1/500, 1/1000, 1/2000, 1/5000,
1/10000 sec.; AGC Gain: 0, 6, 12, 18 dB
eFlickerless: 1/100(NTSC), 1/120(PAL) sec.; AGC Gain: 10~36 dB
fAuto IRIS: 1/60(1/50) sec.; AGC Gain: 10~36 dB
S
p
ecification
Sync. mode: Internal sync. / Line lock
V Phase adjustment: Line Phase: 0~354°, 60 steps var. on screen
Gamma correction: 7 modes selectable on screen
Video output: BNC VBS, 1.0Vp-p, 75 ohm
S-Video: Mini Dim S-Video, Y: 1.0Vp-p, 75ohm, C: 286mV, 75ohm(NTSC);
300mV, 75ohm(PAL)
Day/Night: On / Off
Audio: Optional
Lens mount: C/CS mount
Power source: 90~265VAC or AC24V/12VDC
Dimension: 56 x 68 x 101 mm
Operating temperature: 0oC to +50oC
Power consumption: 5W max.
<CX480-DN>
Ma
j
or Parts Names and their Functions
≥
∝
11
13
←
↑
→
↓
°
±
≥
×
″
14
←
↑
→
↓
°
±
×
″
13
12
←
↑
→
↓
°
≥
14
12
←
°
↑
″
≥
→
↓
±
←Video Output Connector
This connector is used to connect with the VIDEO IN
connector of the monitor (Video Out: BNC type).
↑Power LED Indicator
This indicator lights comes on when the power of this camera
is on.
→Tact Switcher for Setting
Press the tact switcher to display the setting menu. It is used
to activate an item selected in the SET UP menu.
↓Tact Switcher for Right Cursor
This tact switcher is used to move the cursor to the right and
increase the parameters of the selected item.
°Tact Switcher for Down Cursor
This tact switcher is used to move the cursor downward for
selecting the items in the screen menu.
±Tact Switcher for Left Cursor
This tact switcher is used to move the cursor to the left and
decrease the parameters of the selected item.
″Tact Switcher for Up Cursor
This tact switcher is used to move the cursor
upward for selecting the items in the menu.
≥S-Video / RS-232 port
Connecting Mini Dim Male Connector
to S-Video / RS-232 port for better
video output quality or communication.
×Ground Connector
Connecting to power system ground.
∝Auto Iris Lens Connector
This connector is used to connect with the auto iris lens by a
4-pin male connector.
Pin1
Pin2 Pin3 Pin4
Video Drive +12V GND VD-IRIS GND
DirectDrive Cnt- Cnt+ Drv+ Drv-
11 V/D Switch
Switch for Video Drive Auto IRIS lens or
Direct DriveAuto IRIS lens.
12 Line in power cord
This power cord is for 90 ~ 265 VAC power supply.
13 AC24V/DC12V Compatible Input Terminal
This power terminal is for connecting the 24VAC or 12V
DC power supply cord.
14 Audio Output Connector
This connector is used to connect with an audio device
(Audio Out: RCA connector).
4
3
2
1
V D
Y GND
GND
Y
RX
5V
TX
C GND
C
1. Remove the cover cap from the top of the lens mount.
2. If C mount lens is used, please add the C adaptor mount ring (the 5mm thick ring in the
accessory pack) on top of the lens mount.
3. Mount the lens by turning it clockwise on the lens mount of the camera.
4. If you use the Auto Iris lens, connecting the lens cable to the auto iris lens connector on
the top of the camera.
Mountin
g
The Lens
1. Connect the video output of the camera to a color monitor or other video device
through a 75 ohm type coaxial cable with BNC female connector at camera end.
2. Plug the power cord to the electrical outlet 90~265VAC. Power LED indicates red light
if the power source is properly connected.
3.
Connect the AC 24V or DC 12V power source to the power input terminals. The power
supply connection is illustrated below. Please note that the screw marked ( GND)
should connect to the camera case. Power LED indicates red light if the power source
is properly connected.
Connections
AC24V/DC12V
+
+
DC 12VAdapter +
AC 24VAdapter
AC24V/DC12V
Indice
Altri manuali General Lock Telecamera di sicurezza
