Genie CCTV HDC201 Manuale utente

Megapixel HD-CCTV Day/Night Camera

INFORMATION - This equipment has been tested and found to comply with

limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

◆Do NOT use power sources other than those specified.

◆Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and

should conform to all local codes.

The lightning flash with an arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of uninsulated

dangerous voltage within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING - Changes or modifications not expressly approved by the manufacturer

could void the user's authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Features

Warnings and Precautions

Names and Functions of Parts

Installation

■ Front View 9

■ Bottom View 10

■ Rear View 11

■ Lens

ㆍWhen using an DC auto iris lens

ㆍWhen using a CS-Mount lens

ㆍHD-SDI Output

ㆍComposite Output

ㆍWhen using a C-Mount lens

■ Connecting to a monitor 15

■ Connecting to power 16

■ Control via RS-485 Interface 16

Components 8

Megapixel HD-CCTV Day/Night Camera

■Contents

Camera Operation 17

■ Settings 18

■ Menu 17

ㆍLENS

ㆍEXPOSURE

ㆍWHITE BALANCE

ㆍDAY&NIGHT

ㆍNR

ㆍSPECIAL

ㆍADJUST

ㆍRESET

ㆍEXIT

Specifications 33

Troubleshooting 32

Megapixel HD-CCTV Day/Night Camera

The camera requires periodic inspection.

Contact an authorised technician to carry out the inspection.

Stop using your camera when you find it malfunctioning.

If the camera emits smoke or is unusually hot for a long period, a fire

may be caused.

Do not Install the camera on a surface that can not support it.

If the camera is installed on an inappropriate surface, it may fall and

cause injury.

Do not hold plug with wet hands.

It could cause an electric shock.

Do not dis-assemble the camera.

It may result in an electric shock or other hazards.

Do not use the camera close to a gas or oil leak.

It may result in a fire or other hazards.

■ Features Warning ■

Controlled by OSD Menu

The camera functions are controlled by

selecting text displayed on the monitor

screen.

Additional Functions

MIRROR, SHARPNESS, BRIGHTNESS

functions are also available.

HD (High Definition)

Image Camera

By adopting a Sony Mepapixel CMOS

sensor, the camera produces HD image.

DNR (Digital Noise Reduction)

The amount of low illuminance noise has

been significantly reduced and the signal

to noise ratio (S/N ratio), as well as

horizontal resolution, have been improved

resulting in a clear and sharp image even

in low light.

RS-485 Communication

Control Support

Remote OSD menu control via an RS-485

interface is supported.

Filter Changeable Day & Night

(Optional)

This camera has a function that automatically

selects the mode that is appropriate for

daytime or night-time conditions.

The COLOUR mode operates in daytime

conditions to provide optimum colours and

BW mode operates in night time conditions

to enhance the definition of the image.

Megapixel HD-CCTV Day/Night Camera

■Precautions

Do not install the camera in

extreme temperature conditions.

Do not install the camera under

unstable lighting conditions.

Do not touch the front lens of the

camera.

Only use the camera under conditions where

temperatures are between -10˚C and +50˚C.

Be especially careful to provide ventilation

when operating under high temperatures.

It can cause the image quality to be poor.

Severe lighting change or flicker can cause

the camera to work improperly.

This is one of the most important parts of

the camera. Be careful not to leave fingerprints

on the lens cover.

Do not install or use the camera in an

environment where the humidity is high.

ㆍIf the camera is exposed to spotlight or an object reflecting strong light,

smear or blooming may occur.

ㆍPlease check the power supply satisfies the normal specification before

connecting the camera.

It can cause malfunctions to occur.

If it gets wet, wipe it dry immediately.

Liquids can contain minerals that corrode

the electronic components.

If exposed to radioactivity the CCD will fail.

It can damage the CCD.

Do not drop the camera and protect

it from physical shocks.

Do not expose the camera to rain

or spill beverage on it.

Do not expose the camera to

radioactivity.

Never keep the camera pointed

directly at strong light.

2. AUTO IRIS LENS

CONNECTION PLUG

3. L-WRENCH

4. C-MOUNT ADAPTOR

5. INSTRUCTION GUIDE

1. COLOUR BOX CAMERA

Megapixel HD-CCTV Day/Night Camera

Front View

①Lens protection cap

Cover the lens when not in use.

②CS-Mount lens adaptor

Attach the CS-Mount lens here.

③Back Focus clamp screw

Loosen the clamp screw with a L-wrench before adjusting the

Back Focal length.

■Components Names and Functions of Parts ■

①

② ③

Megapixel HD-CCTV Day/Night Camera

Rear View

Bottom View

④Mounting bracket screw hole

Use the screw hole when fixing the camera on

to the mounting bracket.

Please use the clamp screw as specified in the

picture.

※The mounting bracket can be separated and

attached on the top of the camera.

please do not tighten the screw to a depth of

more than 5mm, otherwise serious damage

can occur to the inside of the camera.

■Names and Functions of Parts Names and Functions of Parts ■

④

⑤Setting OSD

⑥Power

Power LED

⑦Lens Connector

Connection terminal for an auto iris lens.

⑧HD-SDI / Composite

BNC connector for HD-SDIⓐand compositeⓑ.

⑨RS-485

Support RS-485 protocol.

⑩Power input terminal

AC24V / DC12V power input.

⑪Power input terminal

DC12V power input.

⑤ ⑥ ⑦

⑧

⑨

⑩ ⑪

⑤ ⑥ ⑦

⑧

⑨

ⓐ

ⓑ

ⓐ

ⓑ

Megapixel HD-CCTV Day/Night Camera

■Installation Installation ■

Lenses are sold separately. Lenses such as auto iris lens, CS-Mount

lens and C-Mount lens can be used.

1. Peel off about 8mm of the outer skin of the auto iris lens cable.

2. Peel off about 2mm of the outer skin of the insulated conductor inside

thelens cable.

■Lens

Note

ㆍUse of the DC auto iris lens is recommended to achieve the best

results for operating this product effectively.

ㆍKeep the lens clean.

ㆍAny foreign objects and fingermarks on the lens can cause inferior

image quality in low light level conditions.

3. Remove the cover of the auto iris lens connection plug and solder the lens

cable to the connector pin in the plug.

4. Replace the auto iris lens connection plug cover and take off the lens

protection cap, and then attach the auto iris lens to the camera by screwing

it in clockwise.

5. Insert the connection plug that is connected to the auto iris lens cable into

the auto lens connector, which is located on the back of the camera.

Pin No. LENS

No.1 Pin Damping-

No.2 Pin Damping+

No.3 Pin Drive+

No.4 Pin Dreve-

When using an DC auto iris lens

■Installation

Megapixel HD-CCTV Day/Night Camera

Take off the lens protection cap and attach

the CS-Mount lens to the camera by screwing

it in clockwise.

Note

ㆍUse the specified lens connection parts as shown in the picture below.

The use of the wrong sized parts may cause damage

to the inside of the camera or result in poor fitting.

ㆍUse of a lens which is too heavy affects the balance

of the camera and may cause a malfunction.

Please use a lens that weighs less than 450g.

ㆍSelect Av mode if possible when adjusting the

automatic light control (ALC) of an auto lens.

Use of PK mode may cause hunting.

1. Take off the lens protection cap and

attach the C-mount adaptor.

2. Attach the C-Mount lens to the

camera by screwing it in clockwise.

■Connecting to a monitor

HD-SDI Output

ㆍConnect the HD-SDI output terminal located on the back of the

camera to the HD-SDI input port of the HD-SDI monitor.

Composite Output

ㆍConnect the COMPOSITE output terminal located on the back of the

camera to the VIDEO input port of the monitor.

ㆍThe connection method varies depending on the type of monitor and

accessories. Please refer to the monitor user manual.

ㆍTurn off the power when connecting.

When using a C-Mount lens

When using a CS-Mount lens

Megapixel HD-CCTV Day/Night Camera

■Installation

RS-485 Control Port

485 Control Board Connection Port

485+

(+) CONNECTION TERMINAL (TRX+)

(

) CONNECTION TERMINAL (TRX-) 485

Item

Initial value

PET PKT

UART MODE

BAUD RATECamera ID

ENABLE8-NONE-1384001

The camera can be controlled by using an external controller equipped

with RS-485 communications.

• To control using a DVR or keyboard controller

Connect the RS-485 cable (TRX+, TRX-) to the connection port of

the 485 control board in the DVR or controller.

* RS-485 communication default initial values

• To control the camera by constructing an additional controller, use

Pelco-D protocol.

(NEAR Key : Enters into OSD menu or Set key function)

Note

■Control via RS-485 Interface

■Menu

Camera Operation ■

Check the standard power requirement before connecting to power.

■Connecting to power

Dual Power Type

(AC24V / DC12V, AC24V Class2)

DC Power Type (DC12V, 1A)

SETUP menu

LENS (selection)

EXPOSURE

WHITE BAL

DAY&NIGHT

SPECIAL

EXIT

ADJUST

RESET

ㆍMANUAL

ㆍ2DNR

ㆍLEVEL

ㆍ

ㆍAUTO

ㆍB/W

ㆍATW

ㆍOUTDOOR

ㆍSHUTTER

ㆍSENS-UP

ㆍACCE

ㆍSHARPNESS

ㆍOSD

ㆍCAM TITLE

ㆍMOTION

ㆍDEFECT

ㆍDC

ㆍSMART NR

ㆍ3DNR

ㆍEXT

ㆍ

ㆍCOLOR

ㆍMANUAL

ㆍAWC→SET

ㆍBRIGHTNESS

ㆍAGC

ㆍDEFOG

ㆍMONITOR

ㆍLSC

ㆍD-EFFECT

ㆍPRIVACY

ㆍRS485

ㆍINDOOR

ㆍBACKLIGHT

ㆍVIDEO

ㆍNTSC/PAL

ㆍLANGUAGE

ㆍVERSION

SETUP

1. LENS DC

2. EXPOSURE

3. WHITE BAL ATW

4. DAY&NIGHT AUTO

5. NR

6. SPECIAL

7. ADJUST

Megapixel HD-CCTV Day/Night Camera

SETUP

1. LENS DC

2. EXPOSURE

3. WHITE BAL ATW

4. DAY&NIGHT AUTO

5. NR

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

Modes can be changed

pushing the jostick

LEFT and RIGHT

Select the desired

menu item by

pushing the joystick

UP and DOWN.

Settings can be made using the 5 buttons located in the camera.

■Settings

1. Press the SET button

ㆍSettings can now be made. The SETUP main menu is displayed on

the monitor.

2. Select a menu item from the list available by pushing the joystick to

UP side and DOWN side.

ㆍThe selected menu is displayed in blue.

■Camera Operation

Note

3. Move the joystick LEFT and RIGHT to change modes.

ㆍWhen you push the joystick LEFT or RIGHT, available values and modes

are displayed in order. Keep pushing the joystick until you get to the

mode you wish to select.

4. Select 'EXIT' and then press the joystick to exit the set up menu.

This function is used to select the LENS type. Because this camera adopts

DC IRIS LENS, choose the 'DC'.

LENS (selection)

SETUP

1. LENS DC

2. EXPOSURE

3. WHITE BAL ATW

4. DAY&NIGHT AUTO

5. NR

6. SPECIAL

7. ADJUST

8. RESET

9. EXIT

ㆍIf appears at the mode selected, it means that there is a sub-menu

which can be selected by pressing the joystick.

Indice

Altri manuali Genie CCTV Telecamera di sicurezza

Genie CCTV

Genie CCTV VRCD-5351 Manuale

Genie CCTV

Genie CCTV HDB2810IR Manuale utente

Genie CCTV

Genie CCTV VRD43/12 Manuale utente

Genie CCTV

Genie CCTV GSH901D Manuale utente

Genie CCTV

Genie CCTV 1000TVL Manuale utente

Genie CCTV

Genie CCTV GD103CHVAI/SMO Manuale utente

Genie CCTV

Genie CCTV ZD2812 Manuale utente

Genie CCTV

Genie CCTV ZW2812 Manuale utente

Genie CCTV

Genie CCTV ASD276 Manuale

Genie CCTV

Genie CCTV MVD83SPX/12 Manuale

Genie CCTV

Genie CCTV TD-D62 Manuale utente

Genie CCTV

Genie CCTV ZD5501 Manuale utente

Genie CCTV

Genie CCTV W70MDIR Manuale utente

Genie CCTV

Genie CCTV DN83TSPX Manuale

Genie CCTV

Genie CCTV GMC3CH Manuale utente

Genie CCTV

Genie CCTV PIXIM VRD83SPX Manuale

Genie CCTV

Genie CCTV GANPRCAM Manuale utente

Genie CCTV

Genie CCTV Raptor II Ruggedized PTZ Manuale utente

Genie CCTV

Genie CCTV ZD9221 Manuale utente

Genie CCTV

Genie CCTV GD5324/2.9 Manuale

Genie CCTV

Genie CCTV DNR300OZ Manuale

Genie CCTV

Genie CCTV AVRCD-6351 Manuale

Genie CCTV

Genie CCTV WAHD2B Manuale utente

Genie CCTV

Genie CCTV TPC 8389 Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente