Genie WHD8EBVAF Manuale utente

User Manual

Please read these instructions carefully before operating the unit

and keep for further reference.

8MP 4-in-1 AHD Starlight IR

Eyeball Camera with 2.8–12mm

Auto Focus Lens

WHD8EBVAF

Intro Section

Please read this instruction carefully before operating the product and keep it for

further reference. All examples and pictures used here are for reference only.

The contents of this manual are subject to change without notice.

CAUTION:

• If the product does not work properly, please contact your dealer or the

nearest service centre. Never attempt to disassemble the camera yourself. We

shall not be responsible for any problems caused by unauthorised repair or

maintenance.

• Do not allow water or liquid into the camera while in use.

• When using the product, you must be in strict compliance with the electrical

safety regulations of the nation and region.

• When the product is mounted on wall or ceiling, the device needs to be ﬁrmly

ﬁxed.

• Make sure the power supply voltage is correct before using the camera.

• Do not drop the camera or subject it to any physical shock.

• If cleaning, please use a clean soft cloth with a little neutral detergent to wipe it

gently.

• Do not aim the camera at the sun or in any area where there is bright lighting.

• The device may be burned out by a laser beam, so when any laser equipment is

in use, make sure that the surface of the device will not be exposed to the laser

beam.

• Do not place the camera in extremely hot, cold , dusty or damp locations, and

do not expose it to high electromagnetic radiation.

• To avoid heat accumulation, good ventilation is required for operating

environment.

Contents

iii

1.0 Introduction..........................................................................................................4

1.1 Product Features...........................................................................................4

1.2 Product Dimensions.....................................................................................4

1.3 Speciﬁcation.................................................................................................5

1.4 Functions ......................................................................................................6

2.0 Cables ..................................................................................................................7

3.0 Product Installation..............................................................................................8

4.0 Call Up Main Menu ...............................................................................................9

The Genie WHD8EBVAF is a professional, modern eyeball design CCTV camera with

a “Starlight” sensor, offering amazing colour images in the lowest of lighting

environments. It boasts 4-in-1 technology (AHD, TVI, CVI, CVBS) and utilises a

superb 2.8mm to 12mm motorised auto focus lens. The camera offers IP67

protection and up to 50m viewing when the IR illumination is switched on.

1.1 Product Features

• 8MP @ 15fps / 5MP @ 20fps / 4MP @ 30fps high resolution, true colour

• Switchable AHD, TVI, CVI, CVBS (960H) output

• CMOS progressive scan, improves moving object capture

• Supports OSD menu

• High speed, long distance and real time transmission

• Auto colour to B&W at low illumination

• Supports ICR switch, true day / night

• Supports noise reduction function

• 30 ~ 50m IR night view distance

• IP67 ingress protection

1.2 Product Dimensions

99.6mm

111.5mm

1.0 Introduction

User Manual 2MP 4-in-1 AHD Starlight IR Eyeball Camera with 2.8–12mm Auto Focus Lens

1.3 Speciﬁcation

Camera

Image Sensor 1 / 2.5” CMOS

Image Size 3840 × 2160

Image System PAL / NTSC

Resolution 8MP

Electronic Shutter Auto

Minimum Illumination Colour : 0.01 Lux @ F1.2, AGC ON

B&W : 0 Lux with IR

Lens 2.8–12 mm motorised lens

Lens Mount D14

S / N Ratio ≥52dB (AGC Off)

Frame Rate 8MP @ 15fps

Video Output AHD / TVI / CVI / CVBS

Functions

IR Distance 30 ~ 50 m

Function Control OSD (COC Control)

Day & Night ICR

Digital WDR No

3D NR Yes

AGC No

Auto White Balance Yes

BLC Yes

LSC No

Defog No

Saturation Yes

Sharpness Yes

Contrast Yes

Smart IR Yes

Image Setting Yes

Defect Correction Auto

Language 11 languages

Angle Adjustment Pan: 0°~360°, Tilt: 0°~80°, Rotation: 0°~360°

Others

Ingress Protection IP67

Power Supply DC12V (± 10%)

Power Consumption IR Off : < 2W, IR On : < 4.5W

Working Environment - 30°C ~ 50°C,

10 % ~ 90 % (Relative Humidity)

Dimensions 111.5 × 99.6 mm

Weight Approximately 0.54Kg (Net)

User Manual 2MP 4-in-1 AHD Starlight IR Eyeball Camera with 2.8–12mm Auto Focus Lens

1.4 Functions

High Resolution

Adopt high performance sensor, providing high deﬁnition and clear image.

High Transmission Performance

Real-time transmission with high speed and long distance.

DNR

Reduce noise from brightness and colour signal.

OSD

It’s easy for the user to call the setup menu and conﬁgure the menu. The camera

settings can be clearly displayed through the main menu.

White Balance

Adjust the colour temperature according to the environment automatically.

ICR Auto Switch

The ﬁlter will ﬁlter infrared light during the daytime and change to normal at night

to ensure a high sensitivity and clear image.

AGC

Adjust the gain of ampliﬁer, enabling the camera to output the standard video

signal in different lighting condition.

Wide Dynamic Range (WDR)

When there are both very bright and very dark areas simultaneously in the ﬁeld of

view, this function will balance the brightness level and provide clear images.

Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the

captured object to make it clearer.

The cables are only for reference. The default video output will be different for

different cameras.

For the camera with video switch cable, there are two kinds of video switches,

button switch and dial switch.

Button Switch: The video outputs will recycle by holding and pressing the button

in the video switch cable for 5 seconds.

Dial Switch: Please set the video output according to the directions described on

the tag of the video switch cable.

Note:

Before switching video outputs, remove the cover of the video switch cable ﬁrst.

* Some models do not have the video switch cable, please go to OSD to change

video outputs.

Video Output

Power Cable

Video Output

Video Switch Cable

2.0 Cables

3.0 Product Installation

Before you start, please make sure that the wall or ceiling is strong enough

to withstand 3x the weight of the camera. Please install the camera in the dry

environment.

1. Attach the drill template to the place where you want to ﬁx the camera and

then drill screw holes according to the drill template.

2. Remove the mounting base of the camera.

3. Route and connect the cables. Then secure the mounting base to the ceiling or

wall with the screws provided.

4. Install the dome and enclosure to the mounting base and then adjust the dome

to obtain an optimum view angle.

5. Adjust the Focus and Zoom screw to get a clear image (if your camera is ﬁxed

lens or motorised lens, please skip this step).

Mounting base

Enclosure

Remove the mounting

base from here

Fixed Screw

Mounting Bas e

Enclosure

Dome

Loosen the ﬁxed screw to

disassemble the camera.

Rotate the mounting base and make sure the marks of

mounting base and enclosure are aligned. Then remove

the mounting base.

Zoom

Focu s

Cove r

Access Main Menu

1. Press Enter key of the rear panel or cable of the camera to go to the main

menu.

2. Select the preview window and right click the mouse to show the following

menu list on the DVR.

3. Click on the toolbar at the bottom of the live preview window (or right click

the mouse to select “PTZ Control”).

4. Select the “OSD” tab and then click / to call up the main menu.

Menu Operation

You can select the menu by clicking (U) or (D) key on the direction area. Click

(L) or (R) key to select the menu on the left. The menu with arrow icon

which means it has sub-menu. Click / to go to the sub-menu or conﬁrm the

settings.

If there are direction keys and enter key on the cables of the camera, you can also

use these direction keys to select menu and the enter key to go to the sub-menu

or conﬁrm the settings.

Note: This series of the camera must be connected to the DVR which supports

calling up main menu of camera. Different DVRs manufactured by different DVR

manufacturers may

have different modes of menu operation. Please refer to the relevant User Manual

of DVR.

* Some models may not support calling up main menu, please take the ﬁnal

product as the standard.

4.0 Call Up Main Menu

Camera Camera1

OSD PresetCruise

Sales +44(0)1707 330541

Enquiries [email protected]o.uk

Website www.genieproducts.co.uk

Indice

Altri manuali Genie Macchina fotografica digitale

Manuali Macchina fotografica digitale popolari di altre marche

Mercury

Mercury 350K Manuale utente

Pentax

Pentax Optio LS 465 Manuale utente

Sanyo

Sanyo VPC-S1085 Manuale utente

GE SMART A1255 Manuale utente

Point Grey

Point Grey Gazelle Manuale utente

Nikon

Nikon COOLPIX A Manuale utente

Pentax

Pentax P-5 Manuale utente

BlazeVideo

BlazeVideo A280 Manuale utente

Sony

Sony MCA-20 Manuale utente

Sony

Sony Alpha DSLR-A290 Manuale utente

ATIK Cameras

ATIK Cameras One Manuale utente

CohuHD Costar

CohuHD Costar 3930 Series Manuale utente

Leica

Leica M10-R Manuale utente

FujiFilm

FujiFilm FinePix A700 Manuale utente

Lorex

Lorex LNZ81P25 Series Manuale utente

GE J1470S Manuale utente

Sony

Sony A6700 Guida utente

Canon

Canon EOS ELAN7 Manuale utente