GeoVision GV-AS1520 Manuale utente
GV-AS1520 Controller
Before attempting to connect or operate this product, please
read these instructions carefully and save this manual for future use.
User’s Manual
AS1520V10-A
© 2018GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, inwhole or inpart,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used inthis manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is a
registered trademark of Microsoft Corporation.
February 2018
Contents
Notice ....................................................................................................................... iii
Optional Devices ......................................................................................................iv
Installation Considerations...................................................................................... v
Chapter 1 Introduction............................................................................................. 1
1.1 Main Features.................................................................................................. 2
1.2 Packing List ..................................................................................................... 3
1.3 Firmware and Software Compatibility............................................................... 3
1.3 Wire Definitions................................................................................................ 4
1.4 LED Status and Beeper ................................................................................... 5
Chapter 2 Getting Started....................................................................................... 6
2.1 Basic Setup for GV-AS1520............................................................................. 6
2.2 Accessing the Web Interface of the GV-AS1520.............................................. 7
2.2 Accessing the Web Interface of the GV-AS1520.............................................. 7
Chapter 3 Installation.............................................................................................. 8
3.1 Connecting RS-485 Card Readers................................................................... 8
3.2 Connecting an Input Device............................................................................. 9
3.3 Connecting Output Devices.............................................................................10
3.4 Connecting the PC..........................................................................................11
3.5 Connecting the Power.....................................................................................12
3.6 Installing GV-AS1520......................................................................................13
Chapter 4 Installing on a Network......................................................................... 16
4.1 Checking the Dynamic IP Address..................................................................17
4.2 Configuring the Static IP Address....................................................................18
4.3 Configuring DDNS Connection........................................................................19
4.3.1 Connection over LAN...................................................................................19
4.3.2 Connection over Internet..............................................................................22
Chapter 5 The Web Interface................................................................................ 26
5.1 Basic Settings.........................................................................................................27
5.1.1 System Setup...............................................................................................27
5.1.2 Upgrading Firmware.....................................................................................29
5.1.3 Changing Login ID and Password................................................................30
5.2 Advanced Settings..................................................................................................31
5.2.1 Function Configuration.................................................................................32
5.2.2 Parameter Configuration..............................................................................35
5.2.3 Time Configuration.......................................................................................37
5.2.4 Input Configuration.......................................................................................39
i
5.2.5 Log Viewer...................................................................................................40
5.3 Extended Device.....................................................................................................41
5.3.1 Extended Reader.........................................................................................41
Chapter 6 Troubleshooting.................................................................................... 43
ii
Notice
1. The product pattern is certified by the FCC. Unauthorized modification of the frequency,
power, or originally designed functions and characteristics of the RFID reader are
prohibited.
2. This product has a water-resistant design. Unauthorized removal of the screws and
case of the product will damage the water-resistant performance and void product
warranty.
3. Cables are water-resistant. Do not damage the shield, as it will also damage water-
resistant performance.
4. The reader should be positioned so that personnel in the area for prolonged periods
may safely remain at least 20 cm (8 in) in an uncontrolled environment from the
reader’s surface.
5. Avoid the interference of other radio frequencies with the look-up table frequency-
hopping spread spectrum (FHSS).
6. This is a Class A product. Class A equipment shall have the following warning in the
instructions for use, to inform the user of the risk of operating this equipment in a
residential environment.
Warning – This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expenses.
iii
Optional Devices
Optional devices can expand the capabilities and versatilities of your GV-AS1520 Controllers.
Consult your sales representative for more information.
GV-SR1251 GV-SR1252 is a card reader that uses a 125 kHz frequency. It has both
Wiegand and RS-485 outputs that can be connected to any standard
access control panel.
GV-Reader
1352 V2
GV-Reader 1352 V2 is a card reader that uses a 13.56 MHz frequency. It
has both Wiegand and RS-485 outputs that can be connected to any
standard access control panel.
GV-RK1352 GV-RK1352 is a card reader with keypad that uses a 13.56 MHz
frequency. The reader has both Wiegand and RS-485 outputs that can be
connected to any standard access control panel.
GV-R1352 GV-R1352 is a card reader that uses a 13.56 MHz frequency. The reader
has both Wiegand and RS-485 outputs that can be connected to any
standard access control panel.
GV-DFR1352 GV-DFR1352 is a card reader that uses a 13.56 MHz frequency. The
reader has both Wiegand and RS-485 outputs that can be connected to
any standard access control panel.
GV-CR420 GV-CR420 is a card reader with a built-in 4MP wide angle IP camera. The
card reader recognizes identification cards and transmits live view through
network connection.
GV-GF
Fingerprint
Readers
The reader (GV-GF1921 / 1922) supports three operation modes:
Fingerprint Only, Fingerprint + Card and Card Only. In Fingerprint Only
mode, the fingerprints are enrolled through GV-ASManager. In Fingerprint
+ Card mode, the fingerprint templates are stored on the user card. In Card
Only mode, the users only need to swipe the card to be granted access.
Readers with optical and capacitance sensors are available.
GV-AS ID Card
/ Key Fob &
GV-UHF Tag
GV-AS ID Card and GV-AS ID Key Fob are ideal for business and
residential environment, where access control is important for security
reasons. 125 KHz and 13.56 MHz cards and key fobs are available. GV-
UHF Tag is ideal for parking lot management. 900 MHz UHF Tag is
available.
Power Adapter Contact our sales representatives for the countries and areas supported.
iv
Installation Considerations
1. Install the RFID reader with the antenna paralleled to the Tag for better reading results.
The Tag receives signals and returns them to the Reader.
2. Install the RFID Reader and Tag as shown below.
Correct Misplaced
v
3. RFID Reader Installation Position
3.1 Do not install RFID Reader near metal or the metallic substance will affect the
electromagnetic field type.
3.2 Recommended height to set RFID reader is 1.8 ~ 2.2 m (5.9 ~ 7.2 ft). The height
should not be lower than the location of RFID Tag.
3.3 Recommended angle to set RFID reader is 15-20 degree. Adjust the angle
according to the actual installation site.
3.4 Keep any barrier away from the reading zone between RFID Reader and the Tag.
vi
4. The RFID Reader must be installed at the same side of the Tag or at the nearest reading
range to the Tag.
4.1 Upper Installation
Proper Improper
4.2 Side Installation
Proper Improper
5. Recommended Tag Position
Vehicles
5.1 Place the tag on the front windshield or headlight, at the nearest reading range to
the reader.
5.2 When placing the Tag on the headlight, keep the Tag away from the metal body
of the vehicle.
5.3 If the car windshield glass contains metallic line, it will affect the reading range.
To avoid such situation, install the Tag on the headlight.
vii
5.4 Windshield insulation films that contain metal ingredients will affect the reading
range. To avoid such situation, install the Tag on the headlight.
Motorcycles
5.5 Install the Tag on the front shield and at the closest range to the RFID Reader.
5.6 If there is no front shield available, it is suggested to install the Tag on the plastic
body of motorcycle at the closest range to the RFID Reader.
viii
Altri manuali per GV-AS1520
2
Indice
Altri manuali GeoVision Controllori
GeoVision
GeoVision GV-AS200 Manuale utente
GeoVision
GeoVision GV-AS Series Manuale utente
GeoVision
GeoVision GV-AS1520 Manuale utente
GeoVision
GeoVision GV-CS1320 Manuale utente
GeoVision
GeoVision GV-AS1520 Manuale utente
GeoVision
GeoVision GV-AS200 Manuale utente
GeoVision
GeoVision GV-AS100 Manuale
GeoVision
GeoVision GV-AS1010 Manuale utente
GeoVision
GeoVision GV-Control Center System V2 Manuale utente
GeoVision
GeoVision GV-AS100 Manuale utente
