Gfp 230 C Manuale utente
Gfp
2
30
C
June
2012
1
OPERATING MANUAL Gfp 230 C
Please read this manual carefully before operating!
Unpacking, assembly, and operating videos are available at
www.gfpsmoothstart.com
Gfp
2
30
C
June
2012
2
Table of Contents
Contents Page
1. Intro uction …………………………………………………… 3
2. Important Safety Instructions………………………………….. 3
3. Installation Safeguar s ……………………………………….. 4
4. General Safeguar s……………………………………………. 5
5. Operating Con itions …………………………………………. 6
6. System Components ………………………………………….. 7
7. Control Panel …………………………………………………. 8
8. Packing List ………………………………………………… .. 9
9. Installation
A. Uncrate the machine……………………………………. 10
B. Remove cross members an machine from Ski ……… . 11
C. Assemble machine stan ……………………………….. 12
D. Set Machine on stan …………………………………... 12
E. Attach supply support brackets………………………… 13
10. A itional installation items …………………………………. 14
11. Loa ing bottom Me ia or Kraft Paper rolls ………………….. 14
12. Installing take up reel…………………………………………. 15
13. Loa ing Film………………………………………………….. 16
14. Threa ing Film ……………………………………………….. 17
15. Operation ……………………………………………………... 18
16. Roller Gap………….. ………………………………………… 18
17. Laminating
A. Single sheets using a sle ………………………………. 19
B. Multiple sheets using a roll of Kraft Paper……………... 20
C. Me ia from a roll……………………………………….. 20
18. Mounting
A. Pre-coating mounting boar s…………………………… 21
B. Mounting print to pre-coate mounting boar s………… 21
19. Troubleshooting ………………………………………………. 22
20. Specifications …………………………………………………. 23
21. Warranty ………………………………………………………. 24
Gfp
2
30
C
June
2012
3
1. Introduction
Thank you for choosing a Gfp laminator. It has been esigne an manufacture to
provi e years of continuous service. Please rea this manual thoroughly before
operating. Please inspect the box an the laminator for shipping amage. Damage
shoul be brought to the attention of the elivering carrier imme iately. For a list of
shipping components see “Packing List” on page 9.
2. Important afety Instructions
In this operating manual you will fin important safety messages regar ing the pro uct.
Rea these instructions carefully, failure to comply with the following safety
proce ures coul result in serious injury.
WAR$I$G Do not attempt to service or repair the laminator. Only
authorize maintenance an service technicians shoul make repairs.
WAR$I$G Do not connect the laminator to an electrical supply or attempt
to operate the laminator until you have completely rea these instructions.
Maintain these instructions in a convenient location for future reference.
WAR$I$G To guar against injury, the following safety precautions must
be observe in the installation an use of the laminator
Gfp
2
30
C
June
2012
4
3.
Installation afeguards
• Shipping amage shoul be brought to the imme iate attention of the
elivering carrier
• Avoi locating the laminator near sources of heat or col . Avoi locating the
laminator in the irect path of force , heate or coole air
• The receptacle must be locate near the equipment an easily accessible.
• Connect the attachment plug provi e with the laminator to a suitably
groun e outlet only. This machine must have reliable earth wire to ensure
the safety of the machine uring operations
• Contact an electrician shoul the attachment plug provi e with the laminator
not match the receptacles at your location
• Ensure that the voltages of the power supply you are using match the
rate working voltages before operations. Do not use incorrect power supply
• Do not use amage wires or sockets. If abnormal con itions occur,
switch off the power supply first.
• Only a license electrician shoul install wiring an outlet for the
laminator
• Do not efeat or remove electrical an mechanical safety equipment such as
interlocks, shiel s an guar s
Gfp
2
30
C
June
2012
5
4. General afeguards
• Keep han s, long hair, loose clothing, an articles such as neckties away from
rollers to avoi entanglement an entrapment. The rollers have pinch points
that can trap bo y parts or clothing an cause serious injury
• Do not use the machines for purposes other than lamination an mounting,
otherwise amages to the machine or acci ents may occur
• Keep out of reach of chil ren
• Keep flammable an wet objects away from the machine.
• Do not use flammable sprays or materials when cleaning the machine
• Do not leave the machine unatten e uring operations.
• Do not mount metal materials or other har objects.
• Do not put burrs, sharp bla e or rigi materials in between the two rubber
rollers.
• Do not attempt to laminate items that excee total recommen e material
thickness of the unit.
• Do not place foreign object insi e the machine.
• Do not cut a hesive films irectly on the surface of the rollers to avoi
amaging the rubber coating.
• Shut own the machine after laminating to avoi misusing this machine by
others.
• Shut own the power before moving the machine
• Note the locations of foot wheels while moving or operating this machine to
avoi injuries to your feet.
• Disconnect from the power supply before repair or maintenance.
• Disconnect from the power supply when the machine is not in use for
a long time.
• When the machine lies i le for a long perio of time, raise the top rubber
roller to avoi the istortion of the rubber surface.
• Perform only the routine maintenance proce ures referre to in these
instructions
Gfp
2
30
C
June
2012
6
5. Operating Conditions
• Place machine on level surface
• Environment requirements：
Ambient temperature: 50⁰ F - 104⁰ F
Humi ity：30%—80%；i eal humi ity：55%
• Due to the static on film rolls, you shoul try to keep the environment clean.
• Provi e enough space aroun machine to ensure the safe an effective operation.
The minimum area covere is 8 ft. x 10 ft.
• Do not irectly cut the films on the surfaces of the rubber rollers to avoi
amages to the rollers.
• Do not put burrs, sharp knives or extra thick an har materials in between the
rollers. Do not leave objects like tools, rulers, knives, etc on the working panels
or the si e cabinets to avoi their being rolle into the machine acci entally an
amaging the rollers.
• For repairs an replacements, please contact your local istributor. Unauthorize
repairs an ismantling will affect future maintenances of the machines.
• The machine can laminate continuously objects less than ½” thick.
For objects over ½” but less than 1” thick, use the pe al switch.
Warning: Do not keep the machines in direct sunshine or near it.
Do not keep the machine in dusty place or places with strong vibrations.
Gfp
2
30
C
June
2012
7
6. ystem Components
1. Bottom supply shaft 11. Liner rewin
2. Front Support beam 12. Top Film supply shaft
3. Brake assembly 13. Brake assembly
4. Fee tray 14. Right si e frame
5. Nip safety guar 15. Roller pressure a justment
6. Left si e frame 16. Power cor
7. Emergency stop switch 17. Control panel
8. Top nip roller 18. Bottom roller support bracket
9. Roller pressure linkage shaft 19. Foot switch
10. Rear exit eck
Gfp
2
30
C
June
2012
8
7. Control Panel
1. Run/ foot pe al switch 2. Spee A justment 3. Forwar / reverse switch
$ote: The machine does not have continuous reverse.
Reverse can only operate using the pedal switch
.
2
1
3
Gfp
2
30
C
June
2012
9
8.Packing List
Remove all parts from shipping create an boxes. Inspect parts an the machine
carefully. Any missing parts shoul be reporte to the shipper upon receipt of
shipment.
Main Machine Crate
Part Quantity Part Quantity
Main Machine 1 Hex Screw 8mm x 80 8
Rewin tube 1 Hex Screw 5mm x 12 16
Support brackets for shafts 4 Plain washer #8 8
Supply shafts 2 Plain washer #5 16
Brake assembly 4 Lock washer #8 8
Stan legs 2 Lock washer #5 16
Stan cross members 2 Zippy knife 1
Allen wrench 6mm 1 Foot switch 1
Allen wrench 5mm 1 Operators manual 1
Allen wrench 4mm 1
Allen wrench 3mm 1
Gfp
2
30
C
June
2012
10
9. Installation
A. Uncrate the machine
1. Remove screws aroun the base of the crate inclu ing corner
supports
2. Lift crate straight up an off the ski
3. Stan legs are insi e behin the machine
Indice
Altri manuali Gfp Plastificatrice
