Gioteck SC3 PRO Manuale utente

SC3NSW-22-MU

SC3NSW-21-MU

EN/ES/FR

FRONT

CONTROLLER DIAGRAM

Minus button Home button

Plus button

Action buttons

Le stick

Capture button

Right stick

Mute button

Volume control

USB-C connector

Directional pad

3.5mm Audio jack

LED bar

BACK

Le bumper (L)

Le trigger (ZL)

Reset button

Programmable button (S2)

Right bumper (R)

Right trigger (ZR)

Program button

Programmable button (S1)

SETUP FOR SWITCH

WIRELESS PAIRING

The controller includes a rechargeable battery that was charged at the time of

manufacturing. If the LED bar ﬂashes red, then the battery needs charging.

To charge, connect to the Switch console or another USB power source via the

USB cable.

From the Switch home menu, select ‘Controllers’ then select ‘Change Grip/Order’. While the following screen is displayed, press and

hold the Home button on the controller you are pairing. Release the Home button and the LED bar starts ﬂashing indicating the

controller is ready to pair.

NOTE: Aer the controller is paired to the Switch, it will automatically connect next time.

WIRED COMMUNICATION OPTION

The controller can communicate with the console via USB (wired) mode. By default, the Switch console has wired communication disabled. Enable

wired communication by going to System Settings / Controllers and Sensors / Pro Controller Wired Communication and set it to On. Connect the

USB charge cable to the controller and Switch console for USB mode.

When you want to use the controller in wireless mode again, disconnect the USB charge cable from the controller, and press the Home button to

wirelessly reconnect to the Switch console.

Low Power: The LED bar blinks red.

Charging: The LED bar blinks orange.

Connected to power and fully charged: The LED bar will turn o.

Pairing mode: When the Home button is pressed, the LED bar ﬂashes white.

Programming back buttons: When the Program button is pressed, the LED bar ﬂashes white

Customizing the colours: See the next section in this manual.

UNDERSTANDING THE LED BAR

• The default colour of the LED bar is orange but it can be set to your preference.

• Press the Program button to cycle through dierent colour settings. Aer the solid colour settings,

there is fast rainbow eect followed by a slower eect. Each press of the Program button advances the cycle.

• Aer the LED bar cycles these settings, the last setting is o.

• Pressing the Program button from the LED o setting restarts the cycle.

CUSTOMIZING THE LED BAR

PROGRAMMING THE BACK BUTTONS (S1 & S2)

1. Press and hold the Program button for 2 sec, the LED bar will start to ﬂash white.

2. While LED bar is ﬂashing, press the desired command buttons. When you have ﬁnished, press either S1 or S2 to complete the

process. The Controller will vibrate, and the LED bar will reset. The S1 or S2 button is now programmed.

Resetting the Back buttons

Press and hold Program button for 5 sec and the Controller will vibrate. All programs are now erased. The S1 and S2 default

mapping is L3 and R3.

1 2 3 4

1,2

AUDIO SETTINGS

• The mute button has no function when a device is not connected to the 3.5mm Audio Jack.

• When an audio device is connected, pressing the Mute button once will mute the connected microphone and the Mute LED will turn red.

• Press the Mute button again to disable the Mute function. The Mute LED will turn o.

• If the Controller is in mute mode when a device is disconnected, mute mode will be disabled, and the Mute LED will be o.

• Press - and + buttons to adjust the device volume.

THUMBSTICK REPLACEMENT

1. Remove by pulling each thumbstick up. Do not twist.

2. Replace by lowering the thumbstick back until a magnetic “click” is heard.

NOTE: If you do not feel a magnetic click when replacing

a thumbstick, check for dust/debris that may have

collected and clear if necessary.

NOTE: The 3.5mm Audio Jack is supported in wired mode only. The controller must be connected to the Switch via the USB cable

for audio features to work.

NOTE: Headphones must be connected to the 3.5mm audio jack to adjust the volume.

iOS/PC Bluetooth Setup. In this mode, the controller emulates an Xbox wireless controller.

Please check game support before use.

Setup: With the controller powered o, Press the A button and Home button together for 3 sec. The LED bar will ﬂash, and the

controller is now in pairing mode. Select the controller from the list of Bluetooth devices on your iOS device or PC. Aer the

connection is made, the LED bar will stop ﬂashing and will show a solid light.

Setup for Android devices. Follow the instructions above but press the Y button and Home button. The controller will show as

“gamepad” in the Bluetooth device list.

IOS, ANDROID AND PC BLUETOOTH SETUP

1. With the USB cable connected to the SC3, connect the other end to the PC.

2. The Controller will now be recognized as an X-input controller device.

3. The default LED bar colour for PC USB Wired mode is Green.

PC SETUP (USB WIRED)

1. Visit www.gioteck.com/ﬁrmware

2. Select the controller you are updating and follow the on-screen instructions.

The controller can be reset to factory settings by inserting a paperclip into the hole on the rear of the controller.

FIRMWARE UPDATES

SPECIFICATIONS

Charging Cable: USB-C to USB Type-A

Cable length: 1m (~3 feet)

Input Power Rating: DC5V, 1.0A

Operating Temperature: 5℃- 35℃(41F – 95F)

Battery Type: Rechargeable Lithium-ion

Battery Capacity: 750mAh

Charging Time: Approximately 2hrs.

Battery Run Time:8 - 20 hrs. Battery life varies signiﬁcantly depending on usage and other factors.

Mass: 230grams

Wireless Connection: Bluetooth 2.1+EDR

Radio frequency: ISM 2.4G

Frequency band: 2402---2480MHz(1MHz)

Maximum radio-frequency: 0dbm

CUSTOMER SUPPORT

Do not return this product to store. Contact us, we can help.

See our FAQs at gioteck.com/support

If you still need help, please contact our support team: [email protected]

SAFETY

Use and handling

•Before use, check that there is plenty of space around you.

•When using the controller, grip it ﬁrmly and make sure it cannot slip out of your hand.

•If using a controller that is connected to the console with a cable, make sure that the cable will not hit a person or object. Also take care to avoid

pulling out the cable from the console.

Exterior protection

Follow the instructions below to help prevent the product exterior from deteriorating or becoming discoloured.

Do not place any rubber or vinyl materials on the product exterior for an extended period. Use a so, dry cloth to clean the product. Do not use

solvents or other chemicals.

Charging the controller

With the console turned on or in sleep mode, connect the controller to the console using the cable.

Battery life and duration

•The battery has a limited lifespan. Battery duration will gradually decrease with repeated usage and age. Battery life also varies depending on the

storage method, conditions of use and environmental factors.

•Charge in an environment where the temperature range is 5℃- 35℃(41F – 95F). Charging may not be as eective outside this range.

When not in use

•When the wireless controller is not used for an extended period, it is recommended that you fully charge it at least once a year to help maintain

battery functionality.

•The lithium-ion battery of the wireless controller is recyclable. When disposing of the wireless controller, remove the battery and follow local

regulations regarding disposing of batteries.

Caution

•Remove the battery in a location out of the reach of small children to help prevent accidental swallowing of small parts such as the screws.

•Be careful not to hurt your nails or ﬁngers when removing the controller casing.

•For safety reasons, attach tape or a seal on the metal part of the battery before disposing.

•Do not handle damaged or leaking lithium-lon batteries.

•If you come into contact with material from a leaking battery, take the following actions:

If the material gets into your eyes, do not rub, instead immediately ﬂush your eyes with clean water and seek medical attention.

If the material comes into contact with the skin or clothes, immediately rinse the aected area

with clean water. Consult your physician if inﬂammation or soreness develops.

•Avoid prolonged use of this product. Take a break at about 30 minute intervals.

•Stop using this unit immediately if you begin to feel tired or if you experience discomfort or pain in your hands or arms during use. If the condition

persists consult a doctor.