Gira Touch sensor 2 Manuale utente
GIRA
Info Touch sensor 2, 24 V potential-free
Installation Instructions
Touch sensor 2, 24 V potential-free 3/12 Page 1 of 3
Function
• touch sensors for connection to 24 V control
systems
• two red status indication LEDs for each rocker
• backlighting
• connection with terminal block at the rear
Connection
Button outputs and LED inputs (FIG. B)
Touch sensor 2, 24 V potential-free
single
triple Order no.: 2001 ..
Order no.: 2003 ..
Sensor terminal
(upper row) assigned
rocker: LED terminal
(lower row)
triple single
1 1 left 1 left 1
2 1 right 1 right 2
3 2 left ---- 3
42right---- 4
5 3 left ---- 5
63right---- 6
---- ---- 7
lighting 8
GIRA
Info Touch sensor 2, 24 V potential-free
Installation Instructions
Touch sensor 2, 24 V potential-free 3/12 Page 2 of 3
Fitting (FIG. C)
1. Remove rockers (5) carefully from touch sensor.
2. Install housing base (1) in the wall.
3. Place design frame (2) over the base and connect
touch sensor (3) to the control system.
4. Plug touch sensor (3) into the base (1).
5. Fasten touch sensor to the base using only the
screws supplied (4)..
6. Slide inscription foil (6) into the touch sensor be-
tween the lateral guides.
Important: If necessary, label foil (6) before fitting.
7. Snap rockers (5) onto the touch sensor.
Removal (FIG. D)
1. Use your thumb and index finger to hold the rocker
on the right and left side.
2. Slide the rocker to the right (1) (or to the left) and
then pull forwards (2) on the right or left side.
3. Loosen the retaining screws
4. If other devices are installed under the same frame
(e.g. socket outlets), they must be detached from
the base as well.
5. Withdraw the touch sensor from the base.
i
Important: Without the retaining
screws the device will not function
properly.
Safety warnings
Attention:Electricalequipmentmustbe installed
and fitted by qualified electricians only.
Failure to observe any of the installation instruc-
tions may cause damage to the device and result
in fire and other hazards.
This device is a safety class III device. Never con-
nect to voltages other than 24 V SELV circuits
(no mains potential !!).
GIRA
Info Touch sensor 2, 24 V potential-free
Installation Instructions
Touch sensor 2, 24 V potential-free 3/12 Page 3 of 3
Technical data
Touch sensor rated
voltage: AC/DC 24 V SELV
LED rated voltage: DC 24 V SELV
Contact current: max. 20 mA per contact
LED current: approx. 1 mA per LED
Connection: 2 x terminal block 9-pole
0.4...0.8 mm single-wire
Power consumption: max. 0.2 W (all LEDs on)
Type of protection: IP 20
Safety class: III
Ambient temperature: -5 °C ... +45 °C
Storage / transport
temperature: -25 °C ... +70 °C
Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your responsible sales-
person (specialist trade/installation company/electrical specialist trade).
They will forward the devices to the Gira Service Center.
Giersiepen GmbH & Co. KG
Electrical Installation
Systems
P.O. Box 12 20
42461 Radevormwald
Germany
Phone +49 (0) 21 95 / 602 - 0
Fax +49 (0) 21 95 / 602 - 191
www.gira.com
Altri manuali Gira Accessori
Gira
Gira 5471 00 Manuale utente
Gira
Gira 5466 02 Manuale utente
Gira
Gira 5461 02 Manuale utente
Gira
Gira KNX 5011 00 Manuale utente
Gira
Gira 0873 00 Manuale utente
Gira
Gira 5068 00 Manuale utente
Gira
Gira 5069 00 Manuale utente
Gira
Gira 1493 00 Manuale utente
Gira
Gira 5472 02 Manuale utente
Gira
Gira System 106 Manuale utente
Gira
Gira 234902 Manuale utente
Gira
Gira CO2-Sensor Manuale utente
Gira
Gira KNX/EIB Manuale utente
Gira
Gira EDA 3902 F Manuale utente
Gira
Gira 5142 00 Manuale dell'operatore
Gira
Gira Observer 70 Manuale utente
Gira
Gira 2688 Series Manuale utente
Gira
Gira GEDU 10 Guida
Gira
Gira 0384 00 Manuale utente
Gira
Gira 5472 02 Manuale utente
