Gitzo GHF2W Manuale utente
GHF2W
2 way fluid head
GHF2W
2 way fluid head
Instructions/Istruzioni/Gebrauchsanweisung/Mode d’emploi/Instrucciones
43
A
D
E
2
C1
1 2
X
A
B
2
1
C
使用说明 / 사용설명서 / 使用説明書
56
7
2
H
1
F
F
8
H
9 10
11 12 13
14
1615
F
N
2
1
English
FIG. 1 – Assemble Handle Bar
Assemble the handle bar “A” as shown in figure.
The pan bar length can be adjusted by locking the bar with knob “B” at
the desired position. The rosette “X” has teeth to allow the pan bar to be
positioned at various intervals.
FIG. 2 – How to remove the camera plate
Hold the camera plate, loosen screw “C” as shown in the diagram, and
lift the plate out of the quick release adaptor.
FIG. 3 – How to mount the equipment on the plate
To tighten the plate you can use
- a coin “A”
- ex key “E”
- the screw’s flip ring “D”
The plate can be mounted on the camera/lens in different directions.
FIG. 4 – How to mount the equipment on the head
Insert the equipment and plate from above. Tighten knob “C” to lock the
camera securely in place. The quick release adaptor allows the sliding of
the plate when the locking lever is not fully locked, and includes a safety
pin that prevents accidental fallings of the camera.
FIG. 5-6-7-8-9-10-11-12-13-14 – Counter balance system
The head is provided with a spring loaded counter balance system (ON/
OFF, 7 positions) to balance the off centre weight of your equipment. The
head is able to support loads up to 4 kg (8.8 lbs), and the balance system
allows to balance a off centre load up to 2,5 kg (5.5 lbs). The head can
be used with or without counter balance system.
FIG. 5
Without counter balance system the head behaves like a standard fluid head:
1. make sure that the tilt control knob “F” is tightened.
2. with one hand pull out and fully rotate the knob “H” to “OFF” position
(following the arrow).
3. with the other hand hold your equipment and unscrew the knob “F”.
FIG. 6
If you want to use the head with counter balance system, proceed as follow:
- unscrew the knob “F” while holding your equipment in order to prevent
it from suddenly flopping
- move the equipment in order to reach the “zero” position (indicated
by arrow )
FIG. 7 - With the other hand fully rotate the knob “H” to “ON” position
(following the arrow).
FIG. 8 - If the equipment doesn’t move, it means that you have reached
the balance point.
FIG. 9 - If the equipment falls, find the balance point as follow.
1. FIG. 10 - Rotate and pull out the knob “H” to “off” position.
2. FIG. 11 - Rotate your equipment in the opposite direction of the fall.
3. FIG. 12 - Reach the first dash after the “zero” position accordingly to
the direction of the fall (always opposite direction) and rotate the knob
“H” to “ON” position until it locks into position.
4. FIG. 13 - Check if the equipment doesn’t move: it means that you have
reached the balance point.
5. FIG. 14 - If the equipment falls down, repeat the instructions above,
selecting the following position (2nd and 3rd dashes after the ). 3rd
position allows the maximum balance capacity.
FIG. 15 – Remove equipment from the head
FIG. 16 – Use
N Pan control knob: friction and lock (360°)
F Tilt control knob: friction and lock (+90/-60°)
Indice
Lingue:
Altri manuali Gitzo Accessori per fotocamere
Gitzo
Gitzo GT5531S Manuale utente
Gitzo
Gitzo Classic Inter Pro Studex Mk2 G1345 G1345 Manuale utente
Gitzo
Gitzo GM2560T Manuale utente
Gitzo
Gitzo GT2540 Manuale utente
Gitzo
Gitzo GS5511S Manuale utente
Gitzo
Gitzo GT3541XLS Manuale utente
Gitzo
Gitzo GT3531LSV Manuale utente
Gitzo
Gitzo GT2940L Manuale utente
Gitzo
Gitzo GT-530 Manuale utente
Gitzo
Gitzo GT5541LS Manuale utente
Gitzo
Gitzo GT2531EX Manuale utente
Gitzo
Gitzo GT2942 Manuale utente
Gitzo
Gitzo GT2941LLVL Manuale utente
Gitzo
Gitzo GT1530 Manuale utente
Gitzo
Gitzo Fluid Gimbal Head Manuale utente
Gitzo
Gitzo GT0531 Manuale utente
Gitzo
Gitzo GT1531 Manuale utente
Gitzo
Gitzo GT2541 Manuale utente
Gitzo
Gitzo GT3540 Manuale utente
Gitzo
Gitzo GT1540 Manuale utente
