GKOLED GKOALG5 Series Manuale utente

PLEASE READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION

— To prevent personal injury or product damage only licensed electricians should install.

— To avoid electric shock or component damage, disconnect power before attempting installation or servicing.

— This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state, and local electric codes and safety standards.

— Disconnect product and allow cooling prior to servicing.

— Any alteration or modiﬁcation of this product is expressly forbidden as it may cause serious personal injury, death, property damage, and/or product malfunction.

— To prevent product malfunction an/or electrical shock this product must be properly grounded.

— This luminaire is designed to operate in ambient temperatures ranging from -40°F to 104 °F and to be horizontally mounted with the LEDs facing down.

— This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the

hazards involved.

— MIN 167°F (75°C) SUPPLY CONDUCTORS

— CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR

— CAUTION - RISK OF FIRE

— When equipped with a Photocell, Adjustable Pole/Slipﬁtter/Yoke mount tilt angle should not exceed 15°.

— This product is not suitable for several special environments, such as places with corrosive gas liquids or high pressure water vapor.

Square/Round Pole (Figure 1)

Mount Installation Guide

(Figure 1)

LED AREA LIGHT

Installation Guide

Series GKOALG5

Content

Mount Installation Guide

Mounting Accessories

Twist-Lock Photocell

Multi-Level Motion Sensor (100W 120-277V)

Multi-Level Motion Sensor (All Conﬁgurations Except 100W 120-277V )

Motion Sensor Dip Switch Settings

Side Plate Gasket

5/16"*1.02(inch)

UNC Bolts

Round Pole

Adaptor

PM4*12(mm) Screws

PM4*12(mm)

Screws

1/2"*1.97(inch)

UNC Bolts

Open Tab

1. Loosen the four PM4*12mm screws and remove the side plate and

rubber gasket from the mounting bracket. Please skip to Step 3 if using a

Square Pole Mount.

2. If using the Round Pole Adaptor, place the adaptor between the arm and

the pole, with the radius side of adaptor towards pole.

3. Pass the two 1/2"*1.97” hex bolts from inside of the pole through Round

Pole Adaptor (if using it) and the back of the arm, slide on ﬂat washers

followed by M14 spring washers, tighten 1/2" nuts.

4. Feed the lead from the arm into the pole and make wiring connections

inside the pole as per the wiring diagram on the next page.

5. Feed the fixture cord into the arm. Align threaded mounting holes of

ﬁxture with exposed ends of the two 5/16"*1.02" hexagon socket bolts,

slide the ﬁxture into the groove of the arm, and tighten the bolts.

6. Inside the arm, make wiring connections between the lead from the

ﬁxture and lead from the arm as per the wiring diagram on the next page.

7. Reinstall the side plate and rubber gasket, tightening the screws. The

gasket should be sitting ﬂush between the side plate and mount, creating

a tight seal around the edges.

Side Plate

M8*20(mm) Screws

PM4*12(mm) Screws 5/16’’*1.02(inch)

UNC Screws

(Figure 4)

(Figure 5)

Yoke Mount (Figure 5)

Wiring Diagram

1. Route the cord into the mounting bracket through the wiring hole,

slide the ﬁxture onto the bracket and tighten the two 5/16" screws.

3. Use the hole pattern on the yoke mount to locate the places to drill the

holes in the installation surface, then attach the mount to the surface

using using 3/8"*1-1/2" hex screws (not included).

3. Loosen the center bolts and set screws, rotate the ﬁxture to the desired

angle, then tighten the center bolts.

4. Make wiring connections per the wiring diagram below.

5. After setting the mount to the desired angle, the center bolts and set

screws should be locked using a manual wrench.

(Figure 3)

Wall Mount (Figure 3)

1. Loosen the four PM4*8(mm) screws and remove the side plate from the

mounting bracket.

2. Attach the back plate to the arm bracket using the KM4*10(mm) screws.

3. Use the provided plastic template to locate the places to drill the holes

in the wall, then attach the bracket to the wall using four 3/8" screws

(not included).

4. Route the power cord into the mounting bracket, slide the ﬁxture onto

the bracket, then tighten the two bottom 5/16" screws.

5. Make wiring connections as per the wiring diagram on the next page,

replace the side plate, and fasten the PM4*8(mm) screws.

5/16"*1.02(inch)

UNC Screws

PM4*8(mm) Screws

Side Plate

PM4*12(mm)

Screws OPEN

Back Plate

KM4*10(mm)

Screws

1/2"*1.46(inch)

UNC Screws

Slipﬁtter (Figure 4)

1. Loosen the two PM4*12(mm) screws and remove the side plate from the

mounting bracket.

2. Route the cord into the mounting bracket through the wiring hole,

slide the ﬁxture onto the bracket and tighten the two bottom 5/16"

screws.

3. Loosen the HM10*25mm hex bolt to adjust the bracket to the desired

angle. Once the ﬁxture is at the desired angle, retighten the HM10*25mm

hex bolt.

4. Make wiring connections per the wiring diagram below.

5. Slip lower ﬁtter over 2 - 3/8" (60 mm) o.d. heavy wall pipe or tenon and

tighten the four M8*20mm hexagon head set screws, making sure not to

pinch any leads.

3.74in. (95mm.)

2in. (51mm.)

ø0.87in.

(ø22mm.)

ø0.43in.

(ø11mm.)

ø0.55in.

(ø14mm.)

5/16’’*1.02(inch)

UNC Screws

Set Screws

Center Bolts

PHOTOCONTROL

MOTION SENSOR

LAMPLOAD

INPUT

WHITE

BLACK RED

Note: Two dimming wires in the the

driver box.

Note: A black/white 12V+ wire may be present and unconnected in some ﬁxtures.

Black

White

Green/Yellow Green

Neutral

Purple

Pink

Ground

Line

5/16"*1.02(inch)

UNC Screws

Adjustable Pole Mount (Figure 2)

1. Loosen the six PM4*12 screws and remove the two side plates.

2. Attach the bracket to the pole using the provided two 3/8" screws.

3. Loosen the M10 screw and adjust the ﬁxture to the desired angle.

3. Route the cord into the mounting bracket through the wiring hole,

slide the ﬁxture onto the bracket and tighten the two bottom 5/16"

screws.

4. Make wiring connections as per the wiring diagram on the next

page, replace the two side plates, and fasten the PM4*12(mm)

screws. When replacing the side plates, make sure that the power

cord is not exposed and does not press against the wiring.

3/8"*1.575(inch)

UNC Screws

HWM4*6(mm)

Screws

PM4*12(mm)

Screws

PM4*12(mm)

Screws

Gasket B

Gasket A Side Plate

M10 Screw

Side Plate

OPEN

(Figure 2)

Mounting Accessories

Mounting Type Accessory Speciﬁcations Quantity

Slipﬁtter Mount

Slipﬁtter Mount Adjustable Slipﬁtter 1

Adaptor

Wall Mount

Pole Mount Arm

Wall Mount Plate

Wall Mount Template

EVA Gasket

Bolt

202 x 177 x 90mm Square Pole Mount Arm

203 x 152 x 5mm Steel Plate

203 x 152 x 1mm Plastic Template

L119W119H30 40° EVA Gasket

KM4 x 10" Stainless Steel Flat Head Bolt

#1/2" x 1.46" Stainless Steel Hexagon Head Bolt

Bolt

Adaptor

#1/2" x 1.97" Stainless Steel Hexagon Head Bolt

202 x 177 x 90mm Square Pole Mount Arm

177 x 88 x 13mm Round Pole Adaptor

Yoke Mount

Yoke Bracket L129.5W60H88 Upper Bracket + L138W60H88 Lower Bracket

+L44.5W115H49 Bracket 1

Other

Twist-Lock Photocell

Receptacle

Bolt

Occupancy Sensor

120-277V 3-Pin

3-Pin Receptacle

PM4x8 Stainless Steel Round Flat Bottom Bolt

120-277 0-10V Bi-Level

Round Pole Mount

Pole Mount Arm

Bolt

202 x 177 x 90mm Square Pole Mount Arm

#1/2" x 1.97" Stainless Steel Hexagon Head Bolt

Square Pole Mount

Photocell Dimensions & Speciﬁcations

120-277V Speciﬁcations

Power Supply: 90-305VAC (Certiﬁed Input Range 100-277VAC) 50/60Hz

Power Consumption: .7W

Illumination Threshold: On at 10-20 Lux, oﬀ at 60-80 Lux

Humidity: Max. 99% RH

Operating Temperature: -40°F to 176°F (-40°C to 80°C)

Net Weight: 90g±2g

480V Speciﬁcations

Power Supply: 347-530VAC (Certiﬁed Input Range 480VAC) 50/60Hz

Power Consumption: .5W

Illumination Threshold: On at 16 Lux, oﬀ at 24 Lux

Humidity: Max. 99% RH

Operating Temperature: -40°F to 158°F (-40°C to 70°C)

Net Weight: 110g

3.228in. (82mm.)

Ø3.188in

Ø81mm.

2.519in. (64mm.)

2.165in. (55mm.)

Optional - Twist-Lock Photocell

1. IMPORTANT: Make sure power to the ﬁxture is disconnected prior to

photocell installation.

2. Push the twist-lock photocell into the receptacle and twist it

clockwise to lock it in place. It is recommended to to install the

photocell facing the NORTH direction as indicated on the top of the

photocell. The receptacle position should be adjusted if necessary.

1. Remove the three screws and open the cover of the power

compartment.

2. Remove the four screws at the location of the photocell hole and take

oﬀ the pressure plate.

3. Place the matching silicone gasket on the photocell receptacle, then use

screws to secure the photocell receptacle to the photocell hole position.

4. Push the twist-lock photocell into the receptacle and twist it

clockwise to lock it in place. It is recommended to to install the

photocell facing the NORTH direction as indicated on the top of the

photocell. The receptacle position should be adjusted if necessary.

5. Complete the wiring for the photocell according to the wiring diagram,

below and connect the wires.

6. Close the cover of the power compartment and tighten the screws,

ensuring that all wires are not pinched.

Photocell & Receptacle

Installation

Only Photocell Installation

(With Preinstalled Receptacle)

PHOTOCELL

WHITE

BLACK

WHITE

RED

LED DRIVER

LED PCB

LED+

DIM+

LED-

DIM-

L-Out

G+

Optional - Multi-Level Motion Sensor

(For 100W 120-277V & All 480V)

Multi-Level Function

Motion Sensor Dimensions & Speciﬁcations

The motion sensor includes the capability for tri-level control functionality, for areas which require a preliminary notiﬁcation consisting of a change

in the brightness of the light before the light switches oﬀ completely. When the sensor is installed, there are 3 lighting modes: 100% --> dimmed

(under reduced natural lighting conditions) --> oﬀ, with 2 periods of selectable waiting time: sensor hold time and sensor stand-by time. Additional

conﬁgurable options include light threshold for sensor operation, and sensor sensitivity/detection area.

When natural lighting conditions

are suﬃcient, the motion sensor

does not turn on the ﬁxture even

when motion is detected.

When natural lighting conditions

fall below a selected threshold,

the motion sensor turns on the

ﬁxture when motion is detected.

After sensor hold time elapses,

the motion sensor dims the

ﬁxture to the stand-by light level

if the natural light conditions are

below the selected threshold.

NOTE: To eliminate the stand-by function, set the Stand-By Light Level to 0.

After the stand-by time period

elapses, the motion sensor

switches the ﬁxture oﬀ

automatically.

2in. (50mm.)

Coverage Side View

Coverage Top View

360° Coverage

1.4in. (34.5mm.)

1.77in.

(45mm.)

1.63in.

(41.3mm.)

Ø2.4in.

61mm.

Ø0.8in.

19.2mm.

1.29in.

(32.8mm.)

32.9mm.

1.4in. (35.8mm.)

0.7in. (18.3mm.)

Speciﬁcations Sensor Coverage

Sensor Factory Settings

Sensor Indicator LED

Power Supply: 12-24V DC

Dimming Control Output: 0-10V, max. 25mA sinking current

Detection Radius & Angle: 30'@ 40'Mounting Height, 360°

Mounting Height: Max. 40'

Humidity: Max. 95% RH

Operating Temperature: -40°F to 167°F (-40°C to 75°C)

•The sensor LED always lights up after power is switched on,

and turns oﬀ after the unit enters the working state.

• The sensor LED will ﬂash once when the unit receives a

sensing signal.

Daylight Sensor Function

Diﬀerences Between Multi-Level Function and Daylight Sensor Function

Select the daylight sensor function by pushing

Multi-Level Function Daylight Sensor Function

• The daylight sensor acts as a threshold to assist motion

sensor operation.

• The light is turned on when motion is detected and natural

lighting conditions are insuﬃcient.

• The light is turned oﬀ after the stand-by time period elapses.

• The daylight sensor works independently of the

motion sensor.

• The light is turned on when the natural light level

exceeds the “Setpoint On” setting and motion is detected.

• The light is turned oﬀ when the natural light level

falls below the “Setpoint Oﬀ” setting.

When movement is

detected, the light

switches on to 100%

brightness.

After sensor hold-time

elapses, the light dims

to the stand-by level.

The light remains

dimmed to the

stand-by level at

night.

When the natural light

level exceeds the

“setpoint oﬀ” light

level, the ﬁxture will

remain oﬀ even when

the space is occupied.

The light stays on at

10% brightness when

motion is not detected

and natural light

conditions are

insuﬃcient.

Settings In This Demonstration:

Hold-Time: 30 Minutes

Setpoint On: 50 Lux

Setpoint Oﬀ: 300 Lux

Stand-By Dimming Level: 10%

Stand-By Period: +∞

(The +∞ Stand-By Period option is only available

when the Daylight Sensor is activated.)

Power On

Check

OFF

Dim

Every

30 Min.

Motion

Hold-Time

Ends

100%

goes in a cycle

at night, 100% brightness

when motion is detected,

and dims to 10% after no

motion is detected for a

long time.

when the remote control is in setting mode.

Motion Sensor Wiring Diagram

100W 120-277V & All 480V

Motion Sensor Installation

1. Remove the three screws and open the cover of the power compartment.

2. Use a screwdriver and hammer, or other suitable tools, to knock

open the Sensor hole along the marked circle.

3. Place the Sensor onto the hole, ﬁt it with a silicone gasket, tighten

the nut, and then install the Sensor lens.

4. Follow the Sensor wiring diagram to connect the wires.

5. Close the cover of the power compartment and tighten the screws

ensuring that all wires are not pinched.

LED DRIVER

LED PCB

LED+

LED-

DIM+

12V+

DIM-

GREEN

WHITE

BLACK

SENSOR

Motion Sensor Dimensions & Speciﬁcations

3.5in. (90mm.)

1.6in. (41mm.)

1.4in. (35.97mm.)

3.2in. (81.16mm.)

2.4in. (60.98mm.)

32.9mm.

1.7in. (42.3mm.)

(18.8imm.)

0.7in.

(12.7imm.)

0.5in.

Speciﬁcations

Power Supply: 120/277VAC, 50/60Hz

Dimming Control Output: 0-10V, default 10V

Detection Radius & Angle: 30'@ 40'Mounting Height, 360°

Mounting Height: Max. 40'

Humidity: 20-90%

Operating Temperature: -40°F to 158°F (-40°C to 70°C)

Important

•Sensor warm up time is 40 seconds. After the sensor connects

to input power the ﬁrst time, the light ﬁxture will stay on for 40

seconds, then dim for normal operation.

• Factory Default Settings: Sensor Detection Range 100%, Sensor

Hold Time 10 Seconds, Light Threshold 30 Lux, Stand-By Light

Level 30%, Stand-By Time: 60 Minutes.

•When any setting is changed using the dip switches or remote

control, the light ﬁxture that the sensor is connected to will turn

on and oﬀ to conﬁrm the change.

Sensor Coverage

Coverage Side View

Coverage Top View

360° Coverage

Ø2.4in.

61mm.

Ø0.8in.

19.2mm.

Multi-Level Function

The motion sensor includes the capability for tri-level control functionality, for areas which require a preliminary notiﬁcation consisting of a change

in the brightness of the light before the light switches oﬀ completely. When the sensor is installed, there are 3 lighting modes: 100% --> dimmed

(under reduced natural lighting conditions) --> oﬀ, with 2 periods of selectable waiting time: sensor hold time and sensor stand-by time. Additional

conﬁgurable options include light threshold for sensor operation, and sensor sensitivity/detection area.

When natural lighting conditions

are suﬃcient, the motion sensor

does not turn on the ﬁxture even

when motion is detected.

When natural lighting conditions

fall below a selected threshold,

the motion sensor turns on the

ﬁxture when motion is detected.

After sensor hold time elapses,

the motion sensor dims the

ﬁxture to the stand-by light level

if the natural light conditions are

below the selected threshold.

After the stand-by time period

elapses, the motion sensor

switches the ﬁxture oﬀ

automatically.

Optional - Multi-Level Motion Sensor

(Excluding 100W 120-277V & All 480V)

Daylight Sensor Function

Select the daylight sensor function by pushing

Settings In This Demonstration:

Hold-Time: 30 Minutes

Setpoint On: 50 Lux

Setpoint Oﬀ: 300 Lux

Stand-By Dimming Level: 10%

Stand-By Period: +∞

(The +∞ Stand-By Period option is only available

when the Daylight Sensor is activated.)

when the remote control is in setting mode.

Power On

Check

OFF

Dim

Every

30 Min.

Motion

Hold-Time

Ends

100%

When movement is

detected, the light

switches on to 100%

brightness.

After sensor hold-time

elapses, the light dims

to the stand-by level.

The light remains

dimmed to the

stand-by level at

night.

When the natural light

level exceeds the

“setpoint oﬀ” light

level, the ﬁxture will

remain oﬀ even when

the space is occupied.

The light stays on at

10% brightness when

motion is not detected

and natural light

conditions are

insuﬃcient.

goes in a cycle

at night, 100% brightness

when motion is detected,

and dims to 10% after no

motion is detected for a

long time.

Motion Sensor Wiring Diagram

Excluding 100W 120-277V & All 480V

Motion Sensor Installation

1. Remove the three screws and open the cover of the power compartment.

2. Use a screwdriver and hammer, or other suitable tools, to knock

open the Sensor hole along the marked circle.

3. Place the Sensor onto the hole, ﬁt it with a silicone gasket, tighten

the nut, and then install the Sensor lens.

4. Follow the Sensor wiring diagram to connect the wires.

5. Close the cover of the power compartment and tighten the screws

ensuring that all wires are not pinched.

SENSOR

LED DRIVER

LED PCB

LED+

LED-

DIM+

DIM-

DIM+

DIM-

L-Out

WHITE

BLACK

WHITE

RED

G+

Instructions for Sensor Parameter Adjustment Using Remote Are Included with the Remote

Dip Switch Parameter Settings

For Both Multi-Level Motion Sensors

Dip Switch 1 & 2: Sensor Detection Range (Sensitivity) Settings

The operating parameters of the motion sensor may be adjusted directly from the sensor or remotely using an optional remote control.

Adjustments made directly to the sensor are done using a set of dip switches on the sensor body, in the locations indicated in the above image.

Each motion sensor parameter may be adjusted by using a set of two adjacent dip switches. Dip switches 1 & 2 set sensor sensitivity, dip switches

3 & 4 set sensor hold time, dip switches 5 & 6 set the level of lux for sensor activation, dip switches 7 & 8 set sensor stand-by light level, and dip

switches 9 & 10 set sensor stand-by time.

Sensor detection range, describes the radius of the circular detection zone on the ground below a sensor installed on a ﬁxture (maximum ceiling

height 40ft). To adjust sensor detection range, put the dip switches to either an ON position ( ) or an OFF position ( ) as indicated in the guide

below.

Dip Switch 3 & 4: Sensor Hold Time Settings

Upon detecting motion, the ﬁxture light can be set to stay on for any

period of time indicated in the options below. Any additional motion

detected before the selected amount of time elapses will restart the

timer. While adjusting the sensor detection zone and performing walk

tests, it is recommended to select the shortest possible hold time. To

adjust sensor hold time, put the dip switches to either an ON position

( ) or an OFF position ( ) as indicated in the guide below.

Dip Switch 7 & 8: Stand-By Light Level Settings

The stand-by light level determines the brightness of the ﬁxture while

the sensor is not detecting motion. To adjust stand-by light level, put

the dip switches to either an ON position ( ) or an OFF position ( )

as indicated in the guide below.

1 2

100%

75%

50%

20%

OFF

SENSOR SENSITIVITY

SETTINGS

3 4

15 Min.

5 Min.

1 Min.

10 Sec.

SENSOR HOLD TIME

SETTINGS

7 8

50%

30%

10%

STAND-BY LIGHT LEVEL

SETTINGS

5 6

50 Lux

30 Lux

10 Lux

Light Sensor Disabled

SENSOR LIGHT

THRESHOLD SETTINGS

Dip Switch 5 & 6: Light Threshold Settings

The sensor light threshold indicates the ambient light level at which

the sensor will begin to control the ﬁxture. To adjust light threshold,

put the dip switches to either an ON position ( ) or an OFF position

( ) as indicated in the guide below.

Dip Switch 9 & 10: Stand-By Time Settings

The stand-by time determines the length of time the ﬁxture stays on

while the sensor is not detecting motion. To adjust stand-by time, put

the dip switches to either an ON position ( ) or an OFF position ( )

as indicated in the guide below.

9 10

60 Min.

30 Min.

1 Min.

+∞

STAND-BY LIGHT LEVEL

SETTINGS

Motion Sensor Dip Switch Settings

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GKOLED Attrezzatura di illuminazione

GKOLED

GKOLED GKOSLG2 Series Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente