Glasdon ECLIPSE Manuale utente

1. Firstly establish the location your Eclipse canopy

is to be sited. To install your canopy we

recommend installing from the upper left fixing

key hole. From the ground measure approximately

2330mm upwards on the wall and mark the centre

using a pencil/scriber (diagram A).

2. Using a 12mm masonry drill bit and a hammer drill,

drill the marked hole to a depth of 110mm (diagram B).

3. Remove the washer from one of the anchors and

hammer the anchor into the drilled hole making sure it

is fully inserted (diagram C). Tighten the anchor using a

17mm socket until it is firmly secure. Once secure, then

unscrew the bolt until it is around 30mm proud of the

wall (diagram D) for the canopy to be hooked onto.

KIT CONTENTS

1 x 1.4m Canopy 4 x Cover rings

4 x Wall fixings 1 x Foam Strip

4 x 50mm Washers

4 x Cover caps

TOOLS REQUIRED

Tape measure 17mm Socket bit

Hammer battery drill Hammer

12mm Masonry drill bit Spirit Level

Socket set

ECLIPSE CANOPY INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

NOTE:

A. B.

C. D.

IMPORTANT NOTE: ENSURE ALL RELEVANT PERSONNEL READ THE POINTS LISTED WITHIN THIS LEAFLET AND

THAT A COPY IS GIVEN TO STAFF INVOLVED WITH THE INSTALLATION AND MAINTENANCE OF THIS PRODUCT.

Anchor

Hole marking for

top left key hole

NOTE: A minimum of 2 persons are required for this installation.

Weight of the canopy: 21kg

2330

4. Lift the canopy up and position the top left key hole slot on the protruding

bolt. Pivot the canopy up at the opposite side ensuring the canopy is level

with the mortar lines or by using a spirit level. (diagram E).

5. Mark the remaining 3 hole

centres of your canopy using a

pencil or scriber (diagram F). The

hole positions are indicated by the

arrows above and below the fixing

slots located in the recesses in the

rear of the canopy. Carefully

remove the canopy from the bolt

and place it down on the floor.

Bolt

E. F.

The canopy is supplied with wall fixings suitable for solid walls of adequate strength. Although most solid

and cavity walls can typically support the canopies, they should be assessed for adequate strength and

stability by a suitably qualified person. There are a number of other anchors and resin fixings that are

probably suitable for your particular site conditions, and the appropriate fixing type should be chosen.

6. Repeat step 2 with the remaining marked holes.

7. Insert the three remaining anchors into the pre-drilled holes and tighten using a 17mm socket.

When tightened fully unscrew all four bolts so only the anchors are left inside the wall.

8. A self-adhesive foam strip is supplied to provide a seal between canopies and/or the wall. Before

using the foam strip firstly clean the recess that runs around the top edge of both sides and the rear of

the canopy, ensuring it is free from dirt/grease. For single unit installations, adhere the foam strip to the

recess at the rear of the unit, cut to the desired length and discard the excess. Where multiple units are

to be sited side by side, the foam strip should be adhered in one piece to the rear and all adjoining

sides of the canopies. NOTE: both abutting sides of the canopies should be fitted with foam strip

providing a double layer for an improved seal.

50mm washer Cover ring Bolt

Recess for

foam strip

NOTE: WHEN INSTALLING CANOPIES SIDE-

BY-SIDE, REPEAT THESE INSTRUCTIONS

FOR EACH ADDITIONAL CANOPY.

HOWEVER CARE SHOULD BE TAKEN TO

MAKE SURE THE CANOPIES ARE

POSITIONED SO THEY ARE AS CLOSE AS

POSSIBLE TO EACH OTHER AND

GENERALLY IN LINE SO THE FOAM STRIP IS

SUFFICIENTLY COMPRESSED TO SEAL.

11. Once secure, the security cover caps

should be pushed into the cover rings.

12. To complete the installation use the

remaining hole plugs and insert into the

unused fixing holes.

9. With all the anchors now inserted into the

wall, place each bolt through a cover ring and

a 50mm washer.

10. Using correct lifting procedures and

equipment, lift the canopy up onto the wall

to align the four fixing slots with the anchor

positions. Carefully re-insert the bolts

through the fixing slots so as to not disturb

the anchor or cross thread the bolt. Tighten

the bolts using a 17mm socket, adjusting

the canopy to level in the process

Outer Slot

Cover cap

2 x Mounting posts

8 x Cover caps

8 x Cover rings

1 x Sealing foam

2 x 17mm socket

Hammer Drill

Drill Bit

8 x 50mm washers

4 x M10 Nyloc nuts

4 x M10 x 100mm Canopy Fixings

1. Place one of the posts onto a raised surface

around 100mm from the floor. Preferably a trolley

so the unit is easy to manoeuvre when assembled.

2. Position the canopy on its side and place

the post into the recess on the back of the unit.

Place a bolt through a cover ring and then

through a 50mm washer and keep to hand.

3. Place a bolt through a cover ring and then

through a 50mm washer. Insert the assembled

bolt through the hole in the canopy until it

protrudes through the post at the back.

4. Place a 50mm washer and a cover cap

over the bolt and secure with a nyloc nut.

5. Using 17mm sockets tighten the bolt until the

canopy is securely fastened to the post.

6. Repeat steps 3,4 & 5 for the second fixing

hole until the post is securely fastened.

ECLIPSE SINGLE CANOPY POST MOUNTING ASSEMBLY INSTRUCTIONS

KIT CONTENTS TOOLS REQUIRED

NOTE: A minimum of 3 persons are required for this installation.

Weight of the complete assembly: 60 kg

7. Using correct lifting techniques lift the

second post and position it into the recess

on the back of the canopy.

8. Repeat steps 3, 4, 5 & 6 until the second

post is securely attached to the canopy.

9. Finally push the cover caps into the

cover ring to secure the fixings.

10. Using correct lifting techniques pivot the

canopy up at one end where it is to be sited.

11. Once the canopy is upright make

sure the posts are perpendicular with

the ground and adjust if necessary.

NOTE:

LIFTING AIDS SHOULD BE USED TO LIFT THE CANOPY AND POSTS WHERE POSSIBLE.

IT IS RECOMMENDED TO POSITION A SPLINT/NOGGIN BETWEEN THE TWO MOUNTING POSTS

TO KEEP THE POSTS RIGID WHEN PIVOTING THE UNIT UPWARD.

Splint Splint

FOR INSTALLATION INSTRUCTIONS FOR GROUND FIXINGS SEE PAGE 6/7

2. Position the first canopy on its side

on a raised platform and place the post

into the recess on the back of the unit.

1. Firstly apply the foam strip to the rear of each

canopy inside the shallow recess as marked above.

= Area to adhere

foam strip

3. Place a bolt through a cover ring and then through a 50mm washer and keep to hand.

4. Position the second canopy back-to-back so the post is sandwiched inside the recesses.

5. Push the bolt through the first fixing hole and the post until it protrudes through both canopies.

Insert a 50mm washer and a cover cap over the bolt and secure with a nyloc nut. Tighten the bolt

using a 17mm socket.

6. Repeat steps 3 & 4 for the second fixing

hole to secure the first post.

7. Using correct lifting techniques slide the

second post into the recess and align the holes.

8. Repeat steps 3, 4 & 5 on the remaining fixing

holes until the second post is secure.

9. Repeat steps 10 and 11 on page 4 to erect the

canopy.

ECLIPSE DOUBLE CANOPY POST MOUNTING ASSEMBLY INSTRUCTIONS

FOR INSTALLATION INSTRUCTIONS FOR GROUND FIXINGS SEE PAGE 6/7

NOTE: A minimum of 3 persons are required for this installation.

Weight of the complete assembly: 86 kg

Bolt

Second Post

Washer

Cover ring

Nut

2 x Mounting posts

8 x Cover caps

8 x Cover rings

1 x Sealing foam

2 x 17mm socket

Hammer Drill

Drill Bit

8 x 50mm washers

4 x M10 Nyloc nuts

4 x M10 x 190mm Canopy Fixings

KIT CONTENTS TOOLS REQUIRED

3. Insert the 60mm anchors into the pre-

drilled holes and gently hammer them down

until they are flush with ground level.

4. Re-position the posts so the fixing holes

align with the anchors. Insert the 70mm bolts

through the 20mm washers and the holes in

the base plate into the anchor sleeves.

Pre-drilled

holes

5. Using a 17mm socket loosely tighten all

four bolts on each base plate before

tightening them fully.

6. Once all bolts are fully tightened, firmly

press the tamper-proof caps onto the bolt

heads to complete the installation.

1. Firstly establish the location your Eclipse

canopy is to be sited. Mark the 8 fixing holes

in the base plate using a pencil or a scriber.

2. Remove the canopy from the marked holes

and drill them using a 16mm masonry drill bit

to a depth of around 80mm. Remove debris

and dust from inside and around the holes.

ECLIPSE CANOPY SURFACE MOUNTING KIT INSTALLATION INSTRUCTIONS

NOTE: ONCE THE CANOPY HAS BEEN PIVOTED UPRIGHT CARE SHOULD BE TAKEN TO MAKE SURE THE

POSTS ARE HORIZONTALLY LEVEL AND PERPENDICULAR TO GROUND LEVEL BEFORE MARKING.

20mm

washer

Base

Plate

KIT CONTENTS

8 x M10 x 70mm Bolt

8 x M10 x 60mm Anchor sleeve

8 x 20mm washer

8 x Tamper proof caps

TOOLS REQUIRED

17mm Socket bit Hammer

Hammer battery drill Spirit Level

16mm Masonry drill bit

Socket set

1. Firstly establish the location your

Eclipse canopy is to be sited. We

recommend digging a minimum hole size

of 500mm x 500mm to a depth of 550mm

as detailed above

ECLIPSE CANOPY CONCRETE IN MOUNTING KIT INSTALLATION INSTRUCTIONS

NOTE:

ONCE THE CANOPY HAS BEEN PIVOTED UPRIGHT CARE SHOULD BE TAKEN TO ENSURE THE

POSTS ARE HORIZONTALLY LEVEL AND SECURE IN THE HOLES

ASSEMBLE THE CANOPY/ CANOPIES TO THE CONCRETE IN POSTS IN THE SAME MANNER AS

INSTRUCTED ON PAGES 3, 4 & 5 OF THIS MANUAL

3. Fill the holes with around 50mm of gravel

or similar material, then position the canopy

into the holes.

2. Insert the cross bar through the hole in

the bottom of each of the posts, these will

anchor the posts when concreted.

4. Ensure the canopies are horizontally

level and the posts are perpendicular to

ground level. To ensure the canopies stay

level it is recommended that chocks or a

stabilising frame is used to keep the posts

secure within the hole prior to concreting.

Posts

5. Once secure pour concrete into the hole

until flush with ground level. Allow concrete

to harden fully to complete your installation.

1130mm Hole

Centres

500

Posts

NOTE:

WE RECOMMEND USING QUICK DRYING

CONCRETE (EG QC10) FOR EASE OF INSTALLATION

Stabilising frame

Should you require any further assistance please contact us on

tel: 01253 891131, fax: 01253 891923 or email: [email protected].

GLASDON MANUFACTURING LIMITED

Poulton Business Park • Poulton-le-Fylde • Lancashire • FY6 8JW

Tel: 01253 891131 • Fax: 01253 891923

e-mail: [email protected] • website: www.glasdon.com

In accordance with our policy of continuous development and improvement, we reserve the right

to make changes in design and specification without notice.

Glasdon Manufacturing Limited products are manufactured under license worldwide and

various components of the models are patented and design registered.

AND ECLIPSE™ ARE TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON

GROUP OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES

• GLASDON cannot be held responsible for claims arising from incorrect installation.

Indice

Altri manuali Glasdon Tenda

Glasdon

Glasdon Echelon Manuale utente

Manuali Tenda popolari di altre marche

OZTENT

OZTENT JV SIGNATURE EDITION Manuale utente

GigaTent

GigaTent Summer Chalet Mini Tent Manuale utente

Coleman

Coleman 2000007827 Manuale

ShelterLogic

ShelterLogic 107153 Manuale utente

Outsunny

Outsunny 84C-230 Manuale utente

Napier

Napier SPORTZ COVE 61 Series Manuale utente

EuroTrail

EuroTrail ATLANTIS PRO Manuale utente

Reimo

Reimo Marina Manuale utente

TiiTENT

TiiTENT TB300 Manuale utente

Coleman

Coleman 2000033134 Guida all'installazione

Ozark Trail

Ozark Trail W784.1 Guida rapida

SlingFin

SlingFin CrossBow 2 Manuale utente

Coleman

Coleman 9600-141 Manuale utente

Palram

Palram Arizona 5000 Wave - WINGS Manuale utente

COVERPRO

COVERPRO 56184 Istruzioni per il montaggio

Vango

Vango Zenith 100 Manuale utente

Costway

Costway PATIOJOY OP70818 Manuale utente

Clarke

Clarke PUC 88 Manuale utente