Global Sources KW561 Manuale utente
Highly Recommended by Outdoor Explorers
Mini Wildlife Scouting Cam Instruction Book
Applicable models：KW561
1
Congratulations on the purchase of your Trail Cam! The Trail Cam is one of the best scouting
cameras available and is designed for long duration performance in the harshest outdoor
environment. It is equipped with built-in infrared LEDs for incredible night vision images and
can be triggered by movement 24 hours a day. The Trail Cam takes high quality full color
daytime images or video with audio or covert infrared black and white nighttime images or
video with audio. Please refer to the notes below and instructions in this manual to ensure
that you are using this product as designed.
2
Notes Before Use
1. When setting camera parameters, please put camera in ON mode.
2. To replace the battery, SD card, firstly turn camera to OFF mode.
4. The color changing of the Indicator
① When camera is updating, indicator light flashes green.
② The indicator light flashes red when it is turned on or ready for operation.
③ When battery is lower, the indicator light turns blue.
④ When being set to long standby time, the indicator flashes purple.
5. Batteries need to be used dry batteries, can not use rechargeable batteries.
6. When the SD card is inserted into camera, make sure that the SD card is not in the
protected position.
7. When using an external power supply, make sure that voltage is correct.
3
Notes Before Use
8. Please take out the battery for long time unused, so as to avoid leakage of the
battery.
9. Camera can not be directly immersed in water, can not be placed in the
environment of strong acid and alkali.
10. Finger can not press the Fresnel lens.
11. Keep the lens and battery compartment clean.
12. Do not use sharp or hard objects to attack or scratch the screen and other damage
things.
4
Notes Before Use
5
1. Move the latches and open the front cover
2. Load 6 lithium AA(non rechargeable) or alkaline AA batteries
3. Insert the SD card and format
4. Switch to the ON Mode
5. Press MENU key
6. Press UP and DOWN key to select Photo or Video Mode
7. Put it in the right position you would like
8. Switch to the ON Mode and the camera has started working after 10S
Quick Starts
Camera Overview
6
PIR
Video Mic
LED Indicator
LENS
IR LED SD
ON OFF Key
Operation Part Battery Case Lock Catch
Dispiay Screen
Standard Accessories
7
1×Belt
1×Manual
1×Gift Box
SD Card
After opening the latch on the right side of the camera, you will see
that it has 6 battery slots. For maximum battery life, we recommend
using 6 lithium AA(non-rechargeable)or alkaline AA batteries.
Please be sure to insert each battery with correct polarity (negative
or“flat”end against the long spring of each battery slot).
Insert the SD card ( OFF mode ) before beginning to operate the
camera. We strongly recommend that you format the SD card at the
first time. SD card is supported up to maximum 256GB capacity.
Power Supply
8
We recommend mounting cam on a sturdy tree with a diameter of about 6 in. (15cm). To get
the optimal picture quality, the tree should be about 16-17 ft(5 meters) away from the place
to be monitored, with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also, keep in mind
that you will get the best results at night when the subject is within the ideal flash range, no
farther than 60' (19m) and no closer than 10'(3m) from the camera.
There are two ways to mount cam: using the provided adjustable strap or the tripod socket.
1. Using the adjustable strap: Push one end of the strap through the two brackets on the
back of cam. Thread the end of the strap through the buckle. Fasten the strap securely
around the tree trunk by pulling the end of the strap firmly so there is no slack left.
2. Using the Tree Nail: The camera is equipped with a socket at the bottom end.
MOUNTING
9
To test whether cam can effectively monitor the area you choose, this test is recommended to
check the sensing angle and monitoring distance of cam. To perform the test:
1. Switch cam to ON mode.
2. Make movements in front of the camera at several positions within the area where you
expect game or subjects to be. Try different distances and angles from camera.
3. If emotion indicator LED light blinks, it indicates that position can be sensed.
The results of your testing will help you find the best place where mounting and aiming the
cam. The height from the ground for placing the device should vary with animal size
appropriately. In general,3 to 6 feet is preferred. You can avoid potential false triggers due to
temperature and motion disturbances in front of the camera by not aiming it at a heat source
or nearby tree branches or brush (especially on windy days).
Sensing Angle and Distance Test
10
Indice
