Global JUNIOR V4-L Guida

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

INSTALLATION & COMMISSIONING MANUAL

VERSION 1 - 03/2015

JUNIOR V4-L

FIRE ALARM CONTROL PANEL

OVERVIEW

INSTALLATION

COMMISSIONING

Introduction............................................................................................... .................... 6

Key Features........................................................................................................................................................................... 6

Access Levels.......................................................................................................................................................................... 7

Typical System Schematic................................................................................................................................................. 8

Power Requirements.......................................................................................................................................................... 9

Battery Requirements......................................................................................................................................................... 10

ABS box information............................................................................................................................................................11

Identifying Components.................................................................................................................................................... 12

EN54 Information................................................................................................................................................................. 15

Recommended Cables....................................................................................................................................................... 16

Analogue Loops, Conventional Sounders and Data Loops........................................................................... 16

Limitations..............................................................................................................................................................................16

Definitions.............................................................................................................................................................................. 17

Introduction........................................................................................................................................................................... 18

Panel......................................................................................................................................................................................... 18

Mains Power Connection......................................................................................................................................... 18

Other Panel connections......................................................................................................................................... 18

Repeaters................................................................................................................................................................................ 18

Panel Main Board - Connection Definitions................................................................................................................. 19

Fitting Junior Expansion Loop Card................................................................................................................................ 20

Data Loops.............................................................................................................................................................................. 21

Panel Rs485.................................................................................................................................................................. 22

Repeater Rs485........................................................................................................................................................... 23

Panel Fibre Optic......................................................................................................................................................... 24

Repeater Fibre Optic.................................................................................................................................................. 25

Analogue Loop...................................................................................................................................................................... 26

Conventional Sounders......................................................................................................................................................27

Auxiliary Fire Relays (2) andFault Relay (1).................................................................................................................... 27

Panel Batteries....................................................................................................................................................................... 28

Introduction........................................................................................................................................................................... 29

The Panel Buttons................................................................................................................................................................ 29

GettingThe Panel Running.............................................................................................................................................. 32

Getting A Repeater Running............................................................................................................................................. 32

Getting Into Programming Mode................................................................................................................................... 33

GettingThe System Running........................................................................................................................................... 34

Communications Check........................................................................................................................................... 34

Panel Check...................................................................................................................................................................34

LearningWhich Devices Are Fitted........................................................................................................................34

........................................................

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

Sounder Audibility Check...................................................................................................................................................

Panel................................................................................................................................................................................

Analogue Loop Monitoring..............................................................................................................................................

Open Circuit Test.........................................................................................................................................................

Conventional Sounder Monitoring................................................................................................................................

Detector Tests........................................................................................................................................................................

Detector Tests By Zone..............................................................................................................................................

Unassigned Detector Test........................................................................................................................................

Wrapping Up Installation And Commissioning........................................................................................................

Battery Fault Message Test......................................................................................................................................

Power Failure Test.......................................................................................................................................................

Programming Functions General...................................................................................................................................

Complete List Of Functions.....................................................................................................................................

Keys To Use Within Functions.................................................................................................................................

General............................................................................................................................................................................

1 Review Historic Log.......................................................................................................................................................

1-1 Display Historic Log.....................................................................................................................................................

1-3 Clear Historic Log..........................................................................................................................................................

1-5 Read/Clear Autostart Count......................................................................................................................................

3 Zones - Disable & Assign............................................................................................................................................

3-1 Disable Zones.................................................................................................................................................................

3-2 Assign Sounder Groups to Zones...........................................................................................................................

3-3 Assign I/O Groups to Zones......................................................................................................................................

3-4 Assign Zone to Device................................................................................................................................................

3-5 Zone Sounder Delay Set-up......................................................................................................................................

4 Sounders - Disable & Assign....................................................................................................................................

4-1 Sounder Configuration...............................................................................................................................................

4-2 Configure Sounder Groups.......................................................................................................................................

4-3 Disable Sounders..........................................................................................................................................................

4-4 Assign Sounder Group to Device............................................................................................................................

4-5 Inhibit Sounders for Device......................................................................................................................................

4-6 Sounder Delay Set-up.................................................................................................................................................

4-7 Override Sounder Delays...........................................................................................................................................

ADVANCED FUNCTIONALITY

SPECIFIC FUNCTIONS

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

5 Input/Output - Disable & Assign

5-1 Configure I/O Groups..................................................................................................................................................

5-2 Select Fault I/O Group.................................................................................................................................................

5-3 Assign I/O Group to Device.......................................................................................................................................

5-4 Inhibit I/O for Device...................................................................................................................................................

5-5 I/O Unit Action upon Evacuate................................................................................................................................

5-6 I/O Unit Delay or Immediate....................................................................................................................................

5-7 I/O Delay Set-up...........................................................................................................................................................

6 Device Set-up..................................................................................................................................................................

6-1 General............................................................................................................................................................................

6-1-1 Disable Loops ..................................................................................................................................................

6-1-2 Device Disable..................................................................................................................................................

6-1-3 Set Selective Disablement...........................................................................................................................

6-1-4 Set Device Reporting Details......................................................................................................................

6-1-5 Set Immediate Evacuate for Device.........................................................................................................

6-1-6 Device Activation Overrides Delays.........................................................................................................

6-1-7 Inhibit Auxiliary Relays..................................................................................................................................

6-1-8 Global Sensitivity Set-up..............................................................................................................................

6-1-9 Configure Timed Sensitivity........................................................................................................................

6-2 .............................................................................................................................

6-2-1 Select Device Heat Grade.............................................................................................................................

6-2-2 Select Device Smoke Sensitivity................................................................................................................

6-3 Discovery Specific.......................................................................................................................................................

6-4 Automatic Address Setting (SAM).........................................................................................................................

6-4-1 Activate ASET Mode (SAM)..........................................................................................................................

6-4-2 Clear Loop..........................................................................................................................................................

6-4-3 Clear Device......................................................................................................................................................

Troubleshooting SAM...................................................................................................................................

7 Monitor Device Counts & Test..................................................................................................................................

7-1 Device Count, Type & Value......................................................................................................................................

7-2 Test Sounders.................................................................................................................................................................

7-3 Sounders on Test Activation.....................................................................................................................................

7-4 Test Zones........................................................................................................................................................................

7-6 Light LED on device.....................................................................................................................................................

............................................................................................................................

Other Device options...................

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

8 General................................................................................................................................................................................

8-1 Time/Date & Timers......................................................................................................................................................

8-1-1 Set Date & Time................................................................................................................................................

8-1-2 Define Day & Night.........................................................................................................................................

8-1-3 Delays Off at Night..........................................................................................................................................

8-1-4 Configure Evacuate Timer............................................................................................................................

8-1-5 Device Starts Evacuate Timer......................................................................................................................

8-2 Special Features Set-up..............................................................................................................................................

8-2-1 Two Devices to Evacuate..............................................................................................................................

8-2-2 Call Points to Evacuate..................................................................................................................................

8-3 Memory - BEWARE, ENGINEERS ONLY...................................................................................................................

8-3-1 Clear Customer Flash Memory...................................................................................................................

8-3-2 Clear Non-Volatile RAM.................................................................................................................................

8-3-3 Calculate Customer Flash Checksum.......................................................................................................

8-3-4 Calculate Program Flash Checksum.........................................................................................................

8-4 Other Features...........................................................................................................................................................

8-4-1 Active/Installation Mode.............................................................................................................................

8-4-2 Upload/Download Link to PC.....................................................................................................................

Uploading/Downloading Customer Site Data......................................................................................

The PC Loader Software................................................................................................................................

Windows® COM PORT Set-up......................................................................................................................

The Panel............................................................................................................................................................

8-4-4 Set User Access Code.....................................................................................................................................

8-4-5 Set User Access Facilities..............................................................................................................................

8-4-6 Select language...............................................................................................................................................

8-4-8 Set Installer Code............................................................................................................................................

..............................................................................................................................................

.................................................................................................................................

TECHNICAL SPECIFICATIONS

CE DECLARATION OF CONFORMITY

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

INTRODUCTION

This document covers the installation and commissioning of a JUNIOR fire alarm panel.This document is intended

for use by a competent, qualified, fire alarm installation engineer.

The JUNIOR fire alarm system should be tailored to the building requirements. The complete system should be

designed to meet all applicable regulations. The installation must then be performed in accordance with the

system design. This manual not only clarifies the components and connections during installation but will also

assist in commissioning and maintenance.

This manual covers the installation and commissioning of a complete system.

ELECTRO-STATIC SENSITIVE DEVICES (ESD)

TAKE SUITABLE ESD PRECAUTIONS WHEN REMOVING OR

INSTALLING PRINTED CIRCUIT BOARDS.

JUNIOR FIRE ALARM PANEL - KEY FEATURES

Single loop panel - Expandable up to 2 loops.

Supports connection to Mini-repeater via RS485, Fibre-Optic or TCP/IP

125 device addresses per loop

Up to96 VULCAN (addressable) ultra low current base sounders (32 address limit)

32 individually programmable sounder addresses

Full SAM & MAM support - Wizmart & GFE protocol only

2 Fire output relays (change-over) and 1 Fault relay (nc - opens on fault)

2 conventional alarm outputs (Individually programmable)

Both detection loops monitored for integrity

384 fully programmable zones

512 fully programmable sounder groups

512 I/O groups

Event log (rolling, 2000 entries)

Available in Apollo, GFE or Wizmart Protocol versions (Hochiki pending)

Compatible with all our own low cost ancillary modules

Backlit LCD display with 4 rows of 40 characters

Programming by integrated keypad or Loader PC software (Juno Net Loader Version 2.12)

Multiple language support (menu selectable)

Integrated 16 zone LED fire zone indication

This manual has been written for panel software revision 3.09.

Newer versions of panel software will be similar but some details may differ.

OVERVIEW

All PCBs contain Electrostatic Sensitive Devices.

Take suitable ESD (Electrostatic Discharge) precautions when removing

or installing printed circuit boards (PCBs).

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

ACCESS LEVEL 1 - General User

Unless otherwise indicated, in order to enable the operation of a particular switch, either a valid User or Programming

Access Code is required to be entered.The only exceptions are the following:

1- Lamp Test Switch

2- Queue Review Switches( Fire, fault, Test and Disabled)

3- Delays Active Switch. During an alarm condition and while delays are active.

By entering a valid User Access Code (Factory default ÇÇÇÇÇ), the authorized user gains access to the operation of

all switches at the front of the panel's display. Authorized User Access also grants the possibility of enabling or

disabling zones.

ACCESS LEVEL 2 - Authorized User Controls

Access to this level is accomplished by the introduction of a code using the panel's keypad. The user code is factory set

to ÇÇÇÇÇand after entering each digit in turn, press OK to confirm entry.

INTERNAL BUZZER SILENCE

The occurrence of any new fire or fault condition will initiate the operation of the internal buzzer. By pressing this

switch, the operation of the buzzer will be stopped until a new fire or fault appears on the system.

ALARM SILENCE/RESOUND

Activates all sounders. A second press deactivates all sounders.The button LED (red) is illuminated whilst the sounders

are activated.

SOUNDERS ENABLE/DISABLE

Pressing this button will enable/disable all sounders both conventional sounder circuits and addressable sounders.

DELAYS ACTIVE

Pressing this button will activate any preprogrammed delays. The yellow LED associated with this button and the

general disablements LED will both be lit. A second press of this button will deactivate the delays and the LED. Under

any fire condition the delays will be activated. If during the course of these delays, at access level 1(General User - code

entry not required), this button is pressed, the delays will be overridden and the sounders and together with any other

fire indicating equipment, will be activated.

USER & INSTALLER ACCESS CODES

To enter both codes use the arrow keys ÆÇÈand when finished press ENTER.

Access Level 2 - Press ENTER, then Authorized User Access Code ÇÇÇÇÇand then press ENTER to confirm entry.

Access Level 3 - Press ENTER, then Installer Access Code ÇÈÇÈÇand then press ENTER to confirm entry

FRONT PANEL KEYPAD KEY'S INSTRUCTIONS

ENTER Used to confirm entry of any data or selection.

ÇUsed to increase selection or number. Also used for code entry.

ÈUsed to decrease selection or number. Also used for code entry.

ÆUsed to change, when required, from Loop 1 to 2 and vice versa.

ESC Escape key. Used to exit a particular function.

NOTE: It is not possible to introduce text for labels using the front panel keypad.

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

ISO ISOOPT ZMU TMP BGU LSM I/O

24 V

CON

DET

CON

DET

CON

DET EOL

4K7

ION

TYPICAL SYSTEM SCHEMATIC

EOL

ALL AUX RELAYS RATED AT

50V AC/DC 1 AMP RESISTIVE

DATA LOOP CONNECTOR

MPX: MULTIPLEXED ZONE LED CONNECTOR

AUXILIARY

POWER SUPPLY

OUTPUT

CLASS CHANGE

REMOTE EVAC.

REMOTE

DISABLEMENT

OF SELECTED

DETECTORS

VOLTAGE FREE

NORMALLY OPEN CONTACTS

NON-LATCHING ACTION

PC Loader

DB9 Female

Connector

EOL

10K

SNDSNDSND

Loop 2

Connections

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

Voltage

EMC Standard EN55022 class B

EN61000-4-2,3,4,5,6,8,11

EN61000-3-2,3

Current

2.4A PSU’s recommended for 1 and 2 loop panels.

The maximum alarm sounder current is 450mA for both conventional sounder circuits.

The maximum quiescent current per loop is 340 mA. The loop short circuit (trip) current is 900mA.

Battery

Internal maximum 24V / 7AH

Primary supply voltage 230 V +10% / -15% V AC

POWER REQUIREMENTS

NEUTRAL

LIVE

MEANWELL

DANGER

230 VOLTS

MODEL: PS-65-27

EARTH

POWER SUPPLY SPECIFICATION - MEANWELL Model: PS-65-27

MAINS SUPPLY VOLTAGE

INTERNAL POWER SUPPLY

TOTAL OUTPUT CURRENT

SUPPLY AND BATTERY CHARGER MONITORED?

BATTERIES MONITORED

MAX BATTERY SIZE

MAINS FUSE

BATTERY FUSE

MAX CURRENT DRAW FROM BATTERY (MAINS FAIL)

230 V +10%/ -15% V AC

Min. 20 V DC - Max. 30 V DC

(28.5 V DC nominal) Max. Ripple 1 V peak-peak

1.7A @ 230 Vac

YES

2 x 12 V 7 AH VRLA

4 A - 250 V Slow Blow - 20 mm

1.85 Amp Resettable - Electronic Fuse

1.5 Amp Max. @ Max. Operating Temperature

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

BATTERY REQUIREMENTS

The battery AH required are calculated from the following formula:

Round up to the next available battery size.

Quiescent currents for individual equipments are listed below:

NOTE: For 2 loop panels 7AH batteries are always recommended.

Quiescent current in mA of

the panel with everything

connected.

Alarm current in Amps

(sounder load)

Standby time required in

hours divided by 1000.

Alarm time in hours

(

)

)20%

Example

A given installation has a single loop panel with 58 mA detector load, 1.4 A sounder load (including loop

sounders) and a 24 hour standby requirement.

Quiescent current in

mA of the panel with

everything connected.

Alarm current in Amps

(sounder load)

Standby time

required in hours

divided by 1000.

Alarm time in

hours 20%

80 (Jr. panel)

58 (detector load)

24 (standby in hrs)

divided by

1000

0.5

(alarm time in hrs)

105 (Jr. panel)

58 (detector load)

138 mA

3.312 AH

= 4.094 AH +20% (0.82 AH) = 4.913 AH

The next available battery size is 5 AH

0.782 AH

0.024 H

0.5 H

163 mA +1.4 A (sounder load)

1.563 A

EQUIPMENT ALARM CURRENT

(mA)

105

QUIESCENT CURRENT

(mA)

Refer to connected devices

Junior Panel

24V auxiliary outputs (2 off)

Manufacturers of Fire Detection Equipment

globalfire.pt

INSTALLATION & COMMISSIONING MANUAL - V1. 03/2015

JUNIOR V4-L - FIRE ALARM CONTROL PANEL

Indice

Altri manuali Global Pannello di controllo

Global

Global JUNIOR V4 Guida

Global

Global JUNO-NET EN-54 Manuale

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche