Global411 MSW300Np4 Manuale utente
4-PORT ADSL2+ MODEM ROUTER w/Realtek rtl8676chipset
NOTICE
This document contains proprietary information protected by copyright. This manual and all
the accompanying hardware, software and documentation are copyrighted. All rights are
reserved.
Global411 Ventures LLC does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty or representation, either expressed
or implied, with respect to the quality, performance, merchantability, or fitness for a particular
purpose of the software or documentation. Global411 Ventures LLC reserves the right to
make changes to the hardware, software and documentation without notification of any
individual or organization of the revision or change.
All brand and product names are the trademarks of their respective owners.
© Copyright 2014
Global411 Ventures LLC
All rights reserved.
MSW300Np4 ADSL2+ Modem Router
User Manual
1
Introduction
The MSW300N51P4 is an ADSL2+ access device that supportsmultiple line modes. The device provides high-speedADSL2+
broadband connection to the Internet or Intranet for high-end users. downlink up to 24 Mbps and uplink up to 1 Mbps.
The device supports WLAN access. It can connect to the Internet through a WLANAP or WLAN device. It complies with IEEE
802.11, 802.11b/g/n specifications, WEP, WPA, and WPA2 security specifications.
Packing List
1 x MSW300Np4
1 x external splitter
1 x power adapter
1 x telephone cables (RJ11)
1 x Ethernet cable (RJ45)
Safety Precautions
Follow the following instructions to prevent the device from risks and damage caused by fire or electric power:
Use the power adapter packed within the device package.
Pay attention to the power load of the outlet or prolonged lines. An overburden power outlet or damaged lines and plugs
may cause electric shock or fire accident. Check the power cords regularly. If you find any damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid damage caused by overheating to the device. The long and
thin holes on the device are designed for heat dissipation to ensure that the device works normally. Do not cover these
heat dissipation holes.
Do not put this device close to a place where a heat source exists or high temperature occurs. Avoid the device from
direct sunshine.
Do not put this device close to a place where it is over damp or watery. Do not spill any fluid on this device.
Do not connect this device to any external power source because any wrong connection may cause power or fire risk.
Do not place this device on an unstable surface or support.
System Requirements
Recommended system requirements are as follows:
A 10/100 base-T Ethernet card is installed on your PC
A hub or Switch. (connected to several PCs through one of Ethernet interfaces on the device)
Operating system: Windows 98SE, Windows 2000, Windows ME, Windows XP
Internet Explorer V8.0 or higher or Netscape / Firefox equivalent
Subscription forADSL service. Your ADSL service provider should provide you with at least one valid IP address (static
assignment or dynamic).
One or more computers, each containing an Ethernet 10/100M Base-T network interface card (NIC).
A hub or switch, if you are connecting the device to more than one (1) computer.
Features
2
Realtek rtl8676
The device supports the following features:
Various line modes
External PPPoE dial-up access
Internal PPPoE/PPPoA dial-up access
1483Briged/1483Routed/MER/IPoA access
Multiple PVCs (up to eight) and these PVCs can be isolated from each other
A single PVC with multiple sessions
Multiple PVCs with multiple sessions
802.1Q and 802.1P protocol
DHCP server
NAPT
Static route
Firmware upgrading through Web, TFTP, or FTP
Resetting to the factory defaults through Reset button or Web
DNS
Virtual server
DMZ
Two-level passwords and usernames
Web interface
Telnet CLI
System status display
PPP session PAP/CHAP
IP filter
IP quality of service (QoS)
Remote access control
Line connection status test
Remote managing through Telnet or HTTP
Backup and restoration of configuration file
Ethernet interface supporting crossover detection, auto-correction, and polarity correction
Universal plug and play (UPnP)
Operating Systems
All versions of Windows, Mac and Linux
ATM Capabilities
All ATM Connection
VPI Range: 0-255
VCI Range: 32-65535
AESA (E.164, DCC, ICD)
PVC Support, UNI 3.0 & 3.1 Signaling
Support AAL 5
Management Support
Web Based GUI 192.168.1.1
Upgrade or update via FTP/HTTP
Command Line Interface via Telnet
Diagnostic Test
Firmware upgradeable
Factory Defaults
IPAddress: 192.168.1.1
Subnet Mask: 255.255.255.0
Encapsulation: RFC 1483 LLC
VPI/VCI: 0/35 MER Bridge mode
Environmental
Operating humidity: 10%-90% non-condensing
Non-operating storage humidity: 5%-95% non-condensing
3
Hardware Installation
Front Panel
Step 1 Connect the DSL interface of the device and the Modem interface of the splitter through a telephone cable.
Connect the phone to the Phone interface of the splitter through a cable. Connect the incoming line to the Line
interface of the splitter.
The splitter has three interfaces:
Line: Connect to a wall phone jack (RJ-11 jack).
Modem: Connect to the ADSL jack of the device.
Phone: Connect to a telephone set.
LED
Color
Function
PWR
Green
On: Power
Off: No power or system boot failed
DSL
Green
On: ADSL link established and active
Blinking: ADSL is trying to establish a connection
Off: No ADSL link
ACT
Green
Blinking: ADSL data activity occurs.
Off: No ADSL data is being sent or received.
LAN
Green
On: LAN link established and active
Blinking: ADSL data activity occurs.
Off: No LAN link.
4
Step 2 Connect the LAN interface of the device to the network card of the PC through an Ethernet cable (MDI/MDIX).
Note:
Use twisted-pair cables to connect with the hub or switch.
Step 3 Plug one end of the power adapter to the wall outlet and connect the other end to the Power interface of the device.
Installing a telephone directly before the splitter may lead to failure of connection between the device and the central office, or
failure of Internet access, or slow connection speed. If you really need to add a telephone set before the splitter, you must add
a microfilter before a telephone set. Do not connect several telephones before the splitter or connect several telephones with
the microfilter.
Port
Function
DSL
Connects the device to an ADSL telephone jack or splitter using a RJ-11
telephone cable
LAN
Connects the device to your PC's Ethernet port, or to the uplink port
on your hub/switch, using a RJ-45 cable
Reset
System reset or reset to factory defaults.
POWER
Connects to the supplied power adapter
Switches the unit on and off
5
Note: Without the splitter, transient noise from the telephone can interfere with the
operation of the ADSL router. As a result, the ADSL router may introduce noise to the
telephone line. To prevent this from happening, a small external splitter must be
connected to each telephone.
Web Configuration
This chapter describes how to configure the router by using the Web-based configuration utility.
Access the Router
The following is the detailed description of accesing the router for the first time.
Step 4 Open the Internet Explorer (IE) browser and enter http://192.168.1.1.
Step 5 In the Login page that is displayed, enter the username and password.
The username and password of the super user are admin and admin.
The username and password of the common user are user and user.
If you log in as a super user, the page shown in the following figure appears. You can check, configure and modify all the
settings.
If you log in as a common user, you can check the status of the router, but can not configure the most of the settings.
Note:
In the Web configuration page, you can click Apply Changes to save the settings temporarily. If you want to save the settings
of this page permanently, click save of Attention that appears at the bottom of the Web page after the configuration.
6
Status
In the navigation bar, choose Status.In the Status page that is displayed contains: System, LAN, WLAN, WAN, Port
Mapping, Statistics and ARP Table.
System
Choose Status > System. The page that is displayed shows the current status and some basic settings of the router, such as
software version, DSP version, uptime, upstream speed and downstream speed.
LAN
Choose Status > LAN. The page that is displayed shows some basic LAN settings of the router. In this page, you can view the
LAN IP address, DHCP server status, MAC address and DHCP client table. If you want to configure the LAN network, refer to
chapter 0 LAN IP.
7
WLAN
Choose Status > WLAN. The page that is displayed shows some basic settings of wireless LAN (WLAN).
WAN
Choose Status > WAN. The page that is displayed shows some basic WAN settings of the router. In this page, you can view
basic status of WAN and DNS server. If you want to configure the WAN network, refer to chapter 0 WAN.
8
Port Mapping
Choose Status > Port Mapping. In this page, you can view the mapping relation and the status of port mapping.
Statistics
Choose Status > Statistics. The Statistics page that is displayed contains Traffic Statistic and ADSL Statistic.
Traffic Statistic
Click Traffic Statistic in the left pane. The page shown in the following figure appears. In this page, you can view the statistics
of each network port.
9
ADSL Statistic
Click ADSL Statistic in the left pane. The page shown in the following figure appears. In this page, you can view the ADSL
line status, upstream rate, downstream rate and other information.
ARP Table
Choose Status > ARP Table. In the ARP Table page, you can view the table that shows a list of learned MAC addresses.
Indice
