Globe 82PC300 Manuale di installazione e funzionamento

82PC300

Power Cutter

First step disassembly

First step assembly

13 18

Guard adjustment lever

LED lamp

Main controller PCBA

HMI

1 Component location

Component locations A) Cover right

B) Cover left

HMI panel

Battery box

Front handle

Guard

G) Water connection system

H) LED lamp

I) Gearbox

Remove the battery

power cutter.

- Check that cutting disc is running freely

- Check LED lamp function

- Check waterflow function

2 Preparations

Tools 1)

2) ESD bracelet

Function test

T20 and T25

13mm

3 Trouble shooting

Error codes by flashing light on HMI

Flashes

Error name

Low speed

Diagnosis

Self check

failure

The main controller PCBA

does not pass the self-test

and will therefore not start

the motor.

Unusual

communi-

Overcurrent

Peak current has been

reached.

This may be due to a stalled motor

during normal use, or failure of an

internal component. The current

This error is shown if the peak

current has been reached for more

* Less then 100% trigger and too

much load in more then 10 sec.

this will accour.

100% trigger can be reached.

make sure 100% trigger is used.

3. Check Hall sensor cables or

connectors if broken.

4.Replace the motor or main

controller PCBA.

check the connectors in the

tool are fully inserted to their

3. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

Replace the main controller PCBA.

main controller PCBA

relies on the COM wire. If this is

then this error will be shown.

issue therefore always try

controller PCBA is

that the motor will turn freely.

2. Check the connectors in the

tool are fully inserted to their

3. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

Replace the main controller PCBA.

When the tool is powered up it

this failure will be indicated.

1. Restart the tool. If

necessary replace the

charged one.

The low speed error is normally

the motor. The tool allows for low

charge this can occur.

occure more easily.

the motor will stop and

report an error when the

speed of the motor is less

than the set minimum.

3 Trouble shooting

Flashes Error name

Over tem-

perature

main

controller

PCBA

Diagnosis

Motor

blocking or

hall sensor

abnormality

When the motor starts or is

already running, if it encounters

the motor stops then this error

code is shown. If the communi-

when the motor is running, then

the motor will stop and this error

will be shown. If the motor uses

hall sensors, and the signals from

them is abnormal, this error

message will be shown.

motor from turning, this error will

be shown.When hall sensors

are used, breakages or

wires can cause this error.

1. Clean the motor and check

it will turn freely and that the

drive line and gearbox run

smoothly.

check the connectors in the

tool are fully inserted to their

3. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

Replace the main controller PCBA.

Switch logic

abnormality for the tool has not been

followed.

An error will be shown if the correct

This includes pressing the trigger

or pulling the safety arm, depending

on the tool.

1. Check the trigger so it is not

stuck, and clean it.

2. Check trigger switch and

3. Check wires and connectors

are ok.

.Replace the main controller PCBA.

of the main controller PCBA

value.

The main controller PCBA includes

the MOSFET power drivers. When

in use these devices get hot. Under

considered normal. This error

indicates that the main controller

PCBA has become too hot, usually

meaning the MOSFETs are too hot.

1. Clean cooling vents inlet and

outlet side.

2. Clean the machine.

3. Check motor fan is ok.

4. Check cooling channel

Replace the main controller PCBA.

check the connectors in the

tool are fully inserted to their

7. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

8. Replace the main controller PCBA.

Low Input

voltage

is below the minimum

requirement for tool

voltage depends on the nominal

discharged below 55V. The tool

will indicate an error if the

measured voltage is too low. The

tool will respond normally when a

check the connectors in the tool

halves.

3. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

Replace the main controller PCBA.

3 Trouble shooting

Flashes Error name

Diagnosis

Over tem-

perature

Motor

Over tem-

perature

of the motor exceeds the

The temperature of the motor is

monitored constantly. In order to

be stopped when this temperature

threshold is reached. Allow the

tool to cool down before using

slots and holes are clear.

1. Ensure the tool is used in an

environemnt where the

ambient temperature is below

the recommended maximum.

the motor. Check that the fan

not broken

check the connectors in the

tool are fully inserted to their

4. Check for wire damage.

Check the ribbon cables,

coloured high current wires.

5. Replac

e main controller PCBA.

6. Replace motor.

temperature measurement.

When this temperature reaches

its maximum threshold, the

too hot. The tool then stops the

motor and shows this error.

touch then replace it with a

use again.

Check that a recommended

operators manual.

use water.

error message, it may need

the main controller PCBA to

be changed.

abnormality

An internal error may be generated

integrity. The failure may occur

due to environmental factors such

as the ambient temperature being

higher than the maximum allowed

for the tool.

1. If the tool is being operated

in an environment where the

ambient temperature exceeds

that recommended for the

tool, allow the tool to cool

again.

2. Replace the main controller

PCBA.

Guard disassembly

Remove the 3 screws (C) and plate (D).

Remove the spring washer (E) and washer (F).

4) Remove the guard (G).

4 First step disassembly

Cutting disc disassembly ؍CAUTION!: SHARP OBJECTS. GLOVES

REQUIRED.

1) Push the button to stop the disc to rotate.

Loosen the screw (A) and washer (B).

3) Remove the cutting disc (C) and inner clamp washer (D).

1) Remove the 2 nuts (A) and 4 screws (B).

4 First step disassembly

Foot and front handle 1) Remove the 2 screws (A).

Remove the water outlet hose assy.(C).

Remove the 3 screws (A) and cover (B).

Remove the water inlet hose assy.(D).

4) Remove the water adjuster (E).

2) Remove the foot (B).

4) Remove the front handle (D).

Water hose

3) Remove the 2 screws (C).

5 First step assembly

Foot and front handle 1) Fit the front handle (D).

2) Fit the foot (B).

3) Fit the screws (A).

Fit the water outlet hose assy.(C).

2) Fit the water inlet hose assy.(D).

Fit the cover (B) and 3 screws (A).

Fit the water adjuster (E).

Water hose

5 First step assembly

Cutting disc assembly ؍CAUTION!: SHARP OBJECTS. GLOVES

REQUIRED.

1) Fit the inner clamp washer (D) and cutting disc (C).

2) Fit the washer (B) and screw (A).

3) Tighten the screw (A): 25 Nm

1) Fit the guard (G).

2) Fit the washer (F) and spring washer (E).

3) Fit the plate (D) and 3 screws (C).

4) Fit the 2 nuts (A) and 4 screws (B).

Guard assembly

Indice

Altri manuali Globe Taglierina

Globe

Globe GFP500 Manuale utente

Manuali Taglierina popolari di altre marche

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuale utente

Makita

Makita DCS552 Manuale utente

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuale utente

Makita

Makita 4112HS Manuale utente

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuale utente

Hitachi

Hitachi CM 4SB2 Guida alla risoluzione dei problemi

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuale utente

GCC Technologies

GCC Technologies AFJ-24S Manuale utente

DeWalt

DeWalt XR LI-ION DCS350N Manuale utente

Baudat

Baudat ES1 Manuale utente

Mafell

Mafell ZAF 200 Guida

Makita

Makita 4100NH Manuale utente

Formax

Formax FD 574 Manuale utente

EINHELL

EINHELL TE-MA 1500 Manuale utente

Husqvarna

Husqvarna Cut-n-Break K 760 Manuale utente

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuale utente

TRI tool

TRI tool 301A Manuale utente

Roller

Roller King 1 1/4 Manuale utente