Glow Brand B85 Guida
WARNING If the information in these instructions is not followed exactly, a re or explosion
may result, causing property damage, personal injury or death.
Donotstoreorusegasolineorotherammablevaporsandliquidsinthevicinityof
thisoranyotherappliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbour’s phone.
• Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
Installationandservicemustbeperformedbyaqualiedinstaller,serviceagencyor
thegassupplier.
User Information Manual
Models
V.20190625
B85,B120&B160
Condensing ASME Boiler
ANSIZ21.13-2017CSA4.9-2017
TableofContents
SAFETY CONSIDERATIONS 3
CONTROLS 7
OPERATING AND SERVICE DISPLAY CODE 9
BOILER OPERATION 11
BOILER DOMESTIC HOT WATER MODES 12
LIGHTING & SHUTTING DOWN THE BOILER 13
MAINTENANCE 14
SERVICE RECORDS 16
GlowBrandC95&C140
Glow Brand B85, B120 & B160 General Safety Warnings
3
SAFETYCONSIDERATIONS
Installation, start-up and servicing of GLOW boilers must be done with due care
and attention, and should only be performed by competent, qualied, licensed
and trained heating technicians. Failure to read and comply with all instructions
and applicable National and local codes may result in hazardous conditions that
could result in property damage and injury to occupants which in extreme cases
might result in death.
DANGER
Indicatesanimminentlyhazardoussituation,which,ifnotavoided,
willresultinsevereinjuryordeath.
WARNING
Indicatesapotentiallyhazardoussituation,which,ifnotavoided,
couldresultinsevereinjuryordeath.
CAUTION
Indicatesapotentiallyhazardoussituation,that,ifnotavoided,
couldresultinminorormoderateinjury.
NOTICE
Indicatesapotentiallyhazardoussituation,that,ifnotavoided,
couldresultinpropertydamage.
WARNING
Iftheinformationinthis
manualisnotfollowedexactly,
areorexplosionmayresult
causingpropertydamage,
personalinjury,orlossoflife.
NOTICE
BlockedVent- This unit is provided with an automatic system that will not allow
the unit to operate if the vent is blocked. If you suspect a blocked vent, follow
these instructions
1. Inspect the inlet and outlet venting outside your house and free any
obstruction.
2. Contact a qualied service technician for assistance.
WARNING
CarbonMonoxideDetector:
Foreachoorlevelcontaining
bedroom(s),acarbon
monoxidedetectorandalarm
shallbeplacedintheliving
areaoutsidethebedroom(s)
aswellasintheroomthat
housestheappliance.
Detectorsandalarmsshall
complywithNFPA720(latest
edition).Failuretocomplywith
requirementsfordetectorsand
alarmsmayresultinserious
injuryordeath..
WARNING
ObstructionHazards-Failure to keep the Vent and Combustion Air-inlet clear
of ice, snow, and other debris may result in property damage, serious injury or
death.
UserResponsibilities
This appliance must be installed and serviced by a licensed, certied and
trained service technician or the WarrantyisVoid. This appliance must
be serviced and inspected annually when operating in normal residential
applications. Other applications (e.g. commercial or other more strenuous
conditions) may require more frequent service and inspection. As the User of
this equipment, you are responsible for ensuring maintenance is performed
at the required intervals. It is also the Users responsibility to ensure Vent and
Combustion Air-Inlet terminations are kept clear of obstructions.
WARNING
ServiceRequirements:
Failuretohavetheappliance
properlyservicedand
inspectedonaregular
basismayresultinproperty
damage,seriousinjuryor
death
User Information Manual
User Information Manual
Glow Brand B85, B120 & B160
4
DANGER
The temperature at which injury occurs varies with the person's age and time of exposure.
Water temperature over 125°F/52°C can cause severe burns instantly or death from scalding.
The slower response time of disabled persons increases the hazards to them. Never allow small children
to use a hot water tap, or to draw their own bath water. Never leave a child or disabled person unattend-
ed in a bathtub or shower.
The appliance should be located in an area where the general public does not have access to the
temperature control.
Lower water temperatures should be used to avoid the risk of scalding. It is further recommended, in all
cases, that the domestic water temperature be set for the lowest temperature which satisfies the user’s
hot water needs. This will also provide the most energy efficient operation of the water heater and
minimize scale formation in the heat exchanger, thus prolonging the life of the unit.
Setting the domestic hot water temperature at 120°F/49°C will reduce the risk of scalds. Some
jurisdictions require settings at specific lower temperatures. The table below shows the approximate
time-to-burn relationship for normal adult skin.
Hot water temperatures required for automatic dishwasher and laundry use can cause scalds and burns
resulting in serious personal injury and/or death.
Temperature
Setting
Over 170°F/77°C
160°F/71°C
150°F/66°C
140°F/60°C
130°F/54°C
120°F/49°C or less
Time to Produce 2nd, 3rd
Degree Burns on Adult Skin
Nearly instantaneous
About 1/2 second
About 1-1/2 seconds
Less than 5 seconds
About 30 seconds
More than 5 minutes
To protect against injury, installing a tempering valve in the domestic hot water supply is
recommended. This valve will reduce point of discharge temperature by mixing cold and hot
water in branch supply lines. Such valves are available from the local plumbing supplier.
Table - Risks of Scalds
Glow Brand B85, B120 & B160 General Safety Warnings
5
WARNING
HOTWATERCANSCALD!
Water Temperatures over 125°F / 52°C can cause severe burns instantly or
death from scalds.
Children, disabled, and elderly are at highest risk of being scalded.
• Never leave then unattended in or near the shower, bathtub or sink.
• Never allow small children to use a not water faucet or draw their own bath.
To avoid any potential scald hazard or if codes require specic water
temperatures at the hot water faucet, the installer may
• Install a eld supplied thermostatic mixing valve at this appliance
• Set the thermostatic mixing valve to the lowest temperature which
satises your hot water needs.
TO AVOID INJURY:
• Feel and adjust water temperature before bathing or showering.
• Water drained from the system drain valve may be extremely hot.
• Make sure all connections are tight.
• Direct water ow away from any person.
WARNING
Close ll valve after any addition of water to the system, to reduce risk of water
escapement.
WARNING
Water quality has a signicant impact on the lifetime and performance of a
GLOW Boiler heat exchanger.
Improperly prepared water in a heating circuit may cause damage to the heat
exchanger through corrosion or fouling. Repeated or uncontrolled water lls will
increase the potential for damage.
High levels of dissolved solids or minerals may precipitate out of the uid onto
the hottest part of the heat exchanger, impairing heat transfer and resulting
in overheating and premature failure. The amount of solids that may form
on the heat exchanger will depend on the degree of hardness and the total
water volume in the system. A high water volume system with a low hardness
count may cause as much damage as a system with less volume and higher
hardness, so it is recommended to treat water so as to remove all dissolved
solids. Other water chemistry allowable limits are as follows:
• Acidity pH is to be between 6.5 and 8.5
• Chloride is to be less than 200 mg/l
• Iron is to be less than 0.3 mg/l
• Copper less than 1.0 mg/l
• Conductivity is to be less than 400μS/cm (at 25°C)
• Hardness is to be 7 Grains or less
WARNING
Should overheating occur or the gas supply fail to shut off, close the manual
gas shut-off valve to the appliance. Failure to follow instructions could result in
explosion causing property damage, serious injury or death.
User Information Manual
User Information Manual
Glow Brand B85, B120 & B160
6
WARNING
Should overheating occur or the gas supply fails to shut off, do not turn off or
disconnect the electrical supply to the pump. Instead shut off the gas supply at a
location external to the appliance
WARNING
Keep boiler area free and clear of combustible materials, gasoline, and other
ammable vapours and liquids.
WARNING
Combustion air must not be drawn from areas containing corrosive air from
swimming pools or spas, including air directly next to outdoor pools and spas.
WARNING
The boiler shall not be exposed to water leaks from piping or components
located overhead. This includes condensation dropping from non insulated cold
water lines overhead
WARNING
In areas of high snow fall, users must check side wall exhaust vent and air
intake terminations on a regular basis to ensure blockages do not occur.
WARNING
Do not use this boiler if any part has been under water. Immediately call a
qualied service technician to inspect the boiler and to replace any part of the
control system and any gas control that has been under water.
WARNING
Bacteria growth can develop in domestic hot water tanks and indirect water
heaters if the minimum water temperature is not set high enough to prevent its
growth.
WARNING
CRYSTALLINESILICA: Carefully read the warnings and handling instructions
in the Installation and Operating Instructions for Refractory Ceramic Fibers
before commencing any service work in the combustion chamber.
Glow Brand B85, B120 & B160 Controls
7
CONTROLS
CH
CH
DHW
DHW
RESET
ENTER
VV
V
V
F
BAR
PSI
BAR PSI OUTSIDE
1 2
6
5
4
3
89 10 117
CAUTION
Beforeadjustingthecontrol
settings,readthecontrol
instructionscarefully
No. Icon Description
1Small Digits Displays the actual (CH) pressure and/or outside temperature (when available).
2Large Digits Display section that shows actual status information: CH, DHW temp, error number etc
3Unit(s) Unit for the value that is being displayed on the large digits
Temperature in degrees Celsius or Fahrenheit. Pressure in bar or psi.
4 Selection/Unit Species what is being displayed on the small digit display section.
The bar/psi icon below indicates that the (CH) pressure is shown.
The outside icon indicates that the outside temperature is displayed.
5Radiator Icon Icon is shown when CH is enabled. Icon blinks when appliance is handling CH demand.
6Faucet Icon Icon is shown when DHW is enabled. Icon blinks when appliance is handling DHW demand.
7 Wrench Icon Icon blinks when service is required.
8Flame Burner is ON (and the appliance is heating)
9No Flame Appliance is unable to start. Icon is displayed when the appliance has a lockout or blocking error.
10 Frost Blinking when (anti) frost protection is active.
11 OTC Outdoor Temperature Compensation is active. The control regulates CH supply water temperature based on the
outside temperature.
Function Description
CH ΛIncrease the CH set-point
CH V Decrease the CH set-point
DHW Λ Increase the DHW set-point
DHW V Decrease the DHW set-point
RESET/ENTER Status overview: Enter the main menu or reset a lockout error by pressing the button for at least 2 seconds.
Glow Brand B85, B120 & B160 User Information Manual
8
USERSETTINGSMENU(0.000)
In the User Settings Menu the user can change the basic settings of the appliance
according to their preference. From the Main Screen press the RESET/ENTER
button on the console to gain access to the Main Menu Screen (Fig.1). Pressing
RESET/ENTER again will grant, access to the User Menu. (Fig.2) A parameter
can be edited by selecting it with RESET/ENTER, after which the value will start
blinking. Then use DHW ^ and DHW V to change the value and press RESET/
ENTER again to store the value. Editing can be canceled by pressing CH ^ or CH
V; the value will not be stored.
CH
CH
DHW
DHW
RESET
ENTER
VV
V
V
Exit the
Menu/
Cancel
Up
Down
Menu/
Enter
Sub
Menu
Number
CH
CH
DHW
DHW
RESET
ENTER
VV
V
V
Exit the
Menu/
Cancel
Up
Down
Menu/
Enter
F
Parameter
Value
Unit
Parameter
Number
Figure 1- User Sub Menu Featured Figure 2-Inside User Menu
Param.
#
Description Default
Value
Range
0.003 CH setpoint 140°F 95°F-171°F
0.048 DHW setpoint 140°F 104°F - 140°F
0.200 System Test Menu (visible only after input of Installer code)
0.901 Temperature unit setting °F °F/°C
0.902 Pressure unit setting psi bar / psi
0.997 Display test. All LCD segments light up. Press any button to quit.
User Menu Parameters
RaisingtheCHsetpointtemperaturebeyond140°F(60°C).
The user is not able to increase the water temperature beyond the 140°F(60°C)
setpoint. Should a higher temperature be required, it is best to contact a
competent, qualied, licensed and trained heating technician.
Glow Brand B85, B120 & B160 Controls
9
StatusOverview
On the status overview the user can view actual operational status information.
Normaloperation
The large digit section shows the supply temperature when the appliance is not
handling demand (standby) or when it is handling demand for CH. When the
appliance is handling DHW demand the DHW temperature is displayed.
The small digits section show the CH pressure and/or Outside temperature
when it is available.
BAR
CHandDHWenabledbutnodemand
The Radiator and Faucet icon indicate that
CH and DHW are enabled. The system is in
standby (no demand), therefore the CH and
DHW icons are not blinking and the supply
temperature is displayed.
BAR
CHandDHWenabledandheatingforCH
demand.
The blinking radiator icon indicates that the
appliance is handling CH demand; therefore
the supply temperature is also displayed.
The faucet icon indicates DHW is enabled.
The ame icon indicates that the burner is
active.
When the display powers up it will attempt
to communicate with the main control and
retrieve the required data. During this
process the ‘init’ message is displayed on the
screen.
When all data was successfully retrieved,
the Status overview is displayed.
When no communication can be established
the ‘no comm’ message is displayed on the
screen.
OPERATINGANDSERVICEDISPLAYCODE
Power-up
Glow Brand B85, B120 & B160 User Information Manual
10
Error/Warningpresent
When an error or warning is present, the small digit section will show one of the
following error types:
• Lockout (Loc)
• Blocking (Err)
• Warning (AttE)
The large digit section will show the error number.
Optional, an alternative message is Displayed alternating with the number
(depending on the error/warning). For a detailed description of the errors, also
see the error list in the instruction & installation manual.
Alternativeerror/warningmessages
Error/Warningno. Description Alternative
message
116 Low_Water_Pressure “FILL”
135 Phase_Neutral_Reversed_Error “PHASE Error”
162 Fill_Warning “FILL”
Lockouterror
The text ‘Loc’ is displayed along with the
lockout number. The ‘No ame’ icon indicates
the burner is disabled.
The appliance must be manually reset by
holding the Reset button.
Blockingerror
The text ‘Err’ is displayed along with the
blocking error number. The ‘No ame’ icon
indicates that the burner is disabled.
The blocking error needs to be resolved.
Warnings
The text ‘AttE’ is displayed along with the
warning number.
The appliance is not blocked, but might have
reduced functionality (depending on the
warning).
De-air
When the de-air sequence is active, the text ‘dAir’ is displayed. On every recycle
of power or loss of power the de-air sequence will activate but will not satisfy
any demand for CH or DHW. The de-air sequence can be cancelled by pressing
and holding buttons CH V +DHW V for at least 3 seconds.
Quickset-points
The CH and DHW set point can be quickly edited via the Status overview:
• Press CH Λ and/or CH V to edit the CH set point (the radiator icon will start to
blink)
• Press DHW Λ and/or DHW V to edit the DHW set point (the faucet icon will
start to blink)
WARNING
Thede-airsequenceis
designedtoremoveairfrom
thesystem,itshouldbe
permittedtocompleteatleast
onecycle;eachcyclelasts
approximately14minutes.
Failuretoadequatelyremove
airfromthesystemcan
damagetheheatexchanger
andvoidthewarranty,and
mayleadtopropertydamage
orpersonalinjury.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Glow Brand Caldaia
