Godex EZ6000 Plus Series Manuale utente

InstallationGuide

EZ-6000PlusRewinder/Stripper

EZ-6000Plus Rewinder / Stripper Installation Guide

EZ-6000Plus背紙回收器/剝紙器安裝說明

1. Rewinder Installation 背紙回收器安裝

1 Motor Module

馬達模組

2 Rewinder Module

背紙回收模組

3 Rewinder Full Sensor Connector Plate

滿紙偵測器連接插頭遮蓋

4 Paper Clip

背紙回收固定夾

5 Label Rewind Bracket

標籤紙回收導紙架

6 Wire Binder

束線帶

7 Belt

傳送皮帶

8 Screw x 10pcs

螺絲x 10pcs

123

1. Place the printer onto a smooth surface

and open the Top Cover.

將機器置於平面上並掀起上蓋。

2. Unscrew all screws that marked in square

as indicated in figure. Remove Top Cover

and Left Cover of the printer.

移除圖中方框內所有的螺絲，將上蓋及側蓋

一起卸下

【

Note /

注意】

Before the installation, please power off the

printer and unplug the power cord.

安裝背紙回收器裝置時

請先將電源開關關閉並

拔除電源線。

3. Remove connectors on both sides of

Power Module.

拔除電源模組兩端的連接線。

4. Unscrew the two screws on bottom of

Power Module and remove the Power

Module.

鬆開電源模組下方兩端的螺絲以移除電源

模組。

5. Remove the connection wire between

main board and Standard Connection

Plate.

移除標準連接插頭遮蓋與主板之間的連接

線。

6. Unscrew the two screws of Standard

Connection Plate from inside of printer and

remove the Standard Connection Plate.

從機器內側移除鬆開標準連接插頭遮蓋的

固定螺絲後，即可移除標準連接遮蓋。

7. Install the Rewinder Full Sensor Connector

Plate with screws that removed from

Standard Connection Plate.

換上滿紙偵測器連接遮蓋後，將遮蓋以原有

的螺絲鎖合固定。

8. Plug the connector of Rewinder Full

Sensor Connector Plate into the socket of

main board as indicated in figure.

將滿紙偵測器連接插頭遮蓋後的連接線插

上主板。

9. Unscrew the screws to remove the

Rewinder Module Cover Plate.

將機器內部側面的背紙遮蓋使用十字螺絲

起子卸下。

10. Take off the Paper Clip from the Liner

Rewind Shaft.

先將背紙回收軸桿上的 U型固定夾取下。

11. Secure the Rewinder Module onto the

printer.

再將背紙回收模組用螺絲鎖合於機器上。

【

Note /

注意】

Before tightening screws, move the connection

wires of Rewinder Module to inside of printer.

鎖合背紙回收模組前

請先將模組上的連接線組

穿過安裝孔後置於機器內部。

12. After the Rewinder Module is installed,

plug the Rewinder Full Sensor Connector

into the socket on plate.

鎖合背紙回收模組後將背紙回收控制接頭

插於背紙回收控制插座上。

13. Rewinder Module installation is complete.

完成背紙回收模組安裝。

14. Put the Motor Module on rear part of

printer and align it to 4 screw holes.

將馬達模組依圖上所示置於機器後端預留

的四個螺絲孔上。

15. Tighten but don’t fully tighten the screws to

save space for adjustment when installing

the belt.

將馬達模組固定螺絲半鎖於螺絲孔上，保留

可移動調整的空間，以方便裝設皮帶。

16. Adjust the position of Motor Module to

install the belt between Motor Module and

Rewinder Module. Fully tighten the screws

after the belt is installed correctly.

將皮帶依圖所示兩端分別套上馬達模組和

背紙回收模組，確認皮帶安裝無誤後即可將

馬達模組固定螺絲鎖緊。

17. Pull connection wires of Rewinder Module

inside of printer through the hole.

將背紙回收模組上的連接線組穿過孔洞，拉

入機器內部。

18. Plug the 5pin connector into the socket on

main board that marked with “CUTTER”.

Plug the 4pin connector into the socket on

main board that marked with “STRIP”.

Plug the motor connector on top of Motor

Module.

將連接線組中的 5pin 接頭插入主板上標

示”CUTTER”的插座；將連接線組中的 4pin

接頭插入主板上標示”STRIP”的插座；最後

再將馬達連接線插在馬達上方的插座。

19. Tie the Motor wire and Rewinder Full

Sensor wire with binder on Motor Module

bracket.

將馬達連接線與滿紙偵測器連接線以束線

帶穿過馬達支架上預留的孔洞後綁住。

【

Note /

注意】

The Rewinder Full Sensor wire should be put

under the belt to avoid the interference.

滿紙偵測器連接線必須從皮帶下方穿過，以避免

干涉皮帶的運作。

20. Install the Power Module and plug the

connectors on both sides of Power

Module.

將電源模組以螺絲鎖回固定後，再把兩端原

先拆下的連接線接回。

21. Install the Left Cover of printer and secure

it with screws.

將機器側蓋蓋回後鎖上固定螺絲。

22. Unscrew the Bottom Cover Screw and

remove the Bottom Front Cover.

將右側面板下方的螺絲順時鐘鬆開，並將右

側面板往上抬起水平卸下。

23. Mount the Label Rewind Bracket onto the

printer and secure it with screws.

將標籤回收導紙架固定並鎖上兩邊螺絲。

24. Label Rewind Bracket installation is

complete.

完成標籤回收導紙架安裝。

25. Install the ribbon and label on printer.

將碳帶與紙捲安裝於機器中。

26. Feed the label through the Printer

Mechanism and around the Label Feed

Guide.

將標籤穿過機心與導紙桿下方。

27. Wrap the label around the Liner Rewinder

Shaft, and use the Paper Clip to secure the

liner.

將標籤環繞於背紙回收模組上，並使用 U型

固定夾固定。

【

Note /

注意】

Make sure the label rewind is in correct

direction.

請注意標籤固定在背紙回收模組的方向。

28. Close the Top cover to complete Label

Rewind Bracket and Rewinder installation.

蓋回上蓋即完成標籤回收導紙架安裝。

【

Note1 /

注意

】

Before starting to rewind labels, please make

sure the printer’s Label Rewind Bracket is

installed properly as instructed.

在啟用標籤回收功能前，請先確定標籤回收導紙

架是否依安裝步驟正確安裝。

【

Note2 /

注意

】

Before starting to rewind labels, please

send ”^XSET,REWINDER,1” command to

printer through QLabel or Hyper Terminal for

turning on the rewinder function.

在啟用標籤回收功能前，需先透過

QLabel

或超級

終端機輸入

”^XSET,REWINDER,1”

命令至條碼

機，以啟動回收功能。

【

Note3 /

注意

】

When use stripper function, please dismount

the rewind bracket first.

如果要啟用自動剝紙功能，必須先將標籤回收導

紙架拆下。

【

Note4 /

注意

】

The maximum length of rewound label is the

total length of a label roll that with 8" OD and 3"

core.

背紙回收模組的最大回收長度約等於一捲

吋外

徑

吋芯

)

紙捲的長度。

2. Stripper Installation 剝紙器安裝

1 Stripper Module

剝紙器

2 Cable Tie Mount x 2pcs

理線座 x 2pcs

3 Screws x 2pcs

螺絲 x 2pcs

1. Unscrew the Bottom Cover Screw and

remove the Bottom Front Cover.

將右側面板下方的螺絲順時鐘鬆開，並將右

側面板往上抬起水平卸下。

2. Unscrew the two screws to remove the

Tear Off Bar.

使用螺絲起子將撕紙片卸下。

3. Hold the Stripper Module and secure it

onto the printer.

輕扶剝紙器並將其用螺絲鎖合固定於機器

上。

4. Plug the Stripper Connector into the socket

on the bottom of the Rewinder Module.

將剝紙器控制連接頭插上位於背紙回收模

組上的剝紙器控制插座。

5. Tie the cables with the Cable Tie Mounts,

and stick the locks onto the Bottom Plate.

將線材固定於理線座上。

6. Pull the Print Head Lever out and flip it

upward to the right.

將印表頭壓力旋轉臂往外拉起，並由後向上

扳起，使印表頭向上抬起。

7. Loose the lock bar (as shown on the arrow

1) of the stripper.

撥開位於剝紙器上的撥柄(如箭頭 1所示)。

8. Follow the direction of arrow 2 to flip the

stripper downward and open it.

依箭頭 2所示方向，將剝紙器打開。

9. Peel off a few labels from the liner (about

400mm of liner), and then feed the liner

through the stripper.

將標籤紙剝離數張只留其背紙(背紙長度約

400mm)後，再將背紙從已打開的剝紙器中

穿過。

10. Close the stripper and secure the lock bar.

推回剝紙器並以剝紙器上的剝柄固定。

11. Wrap the liner around the Liner Rewinder

Shaft, and use the Paper Clip to secure the

liner.

將背紙環繞於背紙回收模組上，並使用U型

固定夾固定。

12. Flip the Print Head Lever downward and

then push it back to the original position.

將印表頭壓力旋轉臂往下推回原位，以關上

印表頭。

13. Close the Top Cover and complete the

Stripper Module installation.

蓋回上蓋即完成剝紙器安裝。

【

Note /

注意】

Before starting to strip labels, please

send ”^XSET,REWINDER,1” command to

printer through QLabel or Hyper Terminal for

turning on the rewinder function.

在啟用剝紙功能前，需先透過

QLabel

或超級終

端機輸入

”^XSET,REWINDER,1”

命令至條碼

機，以啟動回收功能。

P/N 313-032100-101

Altri manuali per EZ6000 Plus Series

Indice

Altri manuali Godex Etichettatrice

Godex

Godex G E300 Manuale utente

Godex

Godex GE300 Manuale utente

Godex

Godex ZX1000i Series Manuale utente

Godex

Godex BP700 Series Manuale utente

Godex

Godex BZB-2U Manuale utente

Godex

Godex T-10 Manuale utente

Godex

Godex DT200+ Series Manuale utente

Godex

Godex GE300 Manuale utente

Godex

Godex LZX400i Manuale utente

Godex

Godex EZPi-1300 Manuale utente

Godex

Godex EZ-DT-2 Manuale utente

Godex

Godex ZX400+ Series Manuale utente

Godex

Godex DT2L Manuale utente

Godex

Godex ZX1000i+ Series Manuale utente

Godex

Godex MX3 series: MX30 Manuale utente

Godex

Godex EZ-DT Manuale utente

Godex

Godex AG3000T Manuale utente

Godex

Godex EZ-4TT Plus Manuale utente

Godex

Godex DT4C Manuale utente

Godex

Godex Stand Alone Printer Manuale utente

Godex

Godex BP1000i Series Manuale utente

Godex

Godex HD830i Manuale utente

Godex

Godex DT200 Series Manuale utente

Godex

Godex C690LJ Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente

Novexx Solutions

Novexx Solutions XLP 604 Manuale utente