Godox V1S Manuale utente
INSTRUCTION MANUAL
说明手册
在使用本产品之前：
请先仔细阅读本手册，以确保您能安全使用。请保存好本手册以备将
来查询参考。
Before using this product:
Please read this user manual carefully in order to ensure your safety
and the proper operation of this product. Keep for future reference.
705-V1S000-00
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
Made In China
TTL锂电圆头机顶闪光灯
TTL Li-ion Round Head Camera Flash
01. Flash Head
08. Hotshoe
06. Type-C USB Port
03. Wireless Sensor
10. Hotshoe Fixing Buckle
07. Battery Remove Button
02. LED Modeling Lamp(01~10)
04. Focus Assist Beam
05. Sync Cord Jack
09. LCD Panel
11. Lithium Battery
● Body
● Control Panel
● LCD Panel
Name of Parts
(1)TTL Autoflash
Zoom : zoom display (Page 51)
: Automatic
: Manual(Page 41)
TTL : TTL autoflash
Focus length (Page 1)5
: High-speed sync
(Page 40)
Distance indicator
display
Flash exposure
compensation amount
(2)M Manual Flash
● When a button or dial is operated, the LCD panel illuminated.
● The display will only show the settings currently applied.
● The functions displayed above function buttons 1 to 4, such
as and <M/A/B/C/D> , change according to settings’
status.
M : Manual flash
Manual flash output
(3)Multi Flash
Multi : Stroboscopic flash
Number of flashes
Flash frequency
17. < > Test Button / Flash
Ready Indicator
13. < >Wireless Selection
Button
24. Function Button 3
22. Function Button 1
23. Function Button 216. ON/OFF Power Switch
20. < >Modeling Lamp Setting
14. Select Dial
15. Set Button
25. Function Button 4
12. <MENU>Flash Menu
Button/Locking Button
18. <ZOOM> Focus Length
Setting
21. <+/->Power Output
19. <MODE>Mode Selection
Button
SYNC
09
05
07
08
04
01
06
02
11
17
23 24
15
13
12
25
16
22
14 18
19
21 20
03
- 33 - - 34 -
10
Firing group
Flash mode
Channel
: Radio transmission
wireless shooting
(4) Radio Transmission Shooting
● Master Unit
● Slave Unit
: Slave
: Slave icon
● LCD Panel in Three Modes
● Attached to the Camera
● 2.4G Radio Transmission: As a Master Unit
● 2.4G Radio Transmission: As a Slave Unit
● What’s in the Box of V1S Kit?
1. Flash Unit 2. Lithium Battery 3. USB Battery Charger
4. USB Cable 5. Charger 6. Mini Stand
7. Protection Case 8. Instruction Manual
● Separately Sold Accessories
The product can be used in combination with the following accessories
sold separately, so as to achieve best photography effects:
XProS & X1S TTL wireless flash trigger, AK-R1 accessory kit for
round flash head, etc.
1 2 34
67
5
- 35 - - 36 -
● Features
1. This flash unit uses Li-ion battery which has long runtime. The
available charge-and-discharge times are 500.
3. Take only 3.5 hours to fully charge the battery by using the
standard battery charger.
2. It is reliably safe. The inner circuit is against overcharge,
overdischarge, overcurrent, and short circuit.
● Cautions
8. If the battery had ceased using for over 3 months, please make a
full recharge.
2. Do not expose to rain or immerse into water. This battery is not
water proof.
1. Do not short circuit.
3. Keep out of reach of children.
4. No over 24 hours’ continuous charging.
5. Store in dry, cool, ventilated places.
6. Do not put aside or into fire.
7. Dead batteries should be disposed according to local regulations.
● Loading and Unloading the Battery
Battery
To unload the battery, hold
1down the battery remove
button and push the battery
downwardly to take it out.
According to the triangle sign
2on the battery pack, insert it
into the compartment until a
white knob locks the battery
with a click sound.
● Battery Level Indication
Make sure the battery pack is securely loaded in the flash. Check
the battery level indication on the LCD panel to see the remaining
battery level.
Battery Level Indication
3 grids
2 grids
1 grid
Blank grid
Blinking
Attaching to a Camera
Attach the Camera Flash.
1● Rotate the hotshoe fixing
buckle to the left and insert
the camera flash into the
camera's hotshoe.
Secure the Camera Flash.
2● Rotate the hotshoe fixing
buckle to the right until it
locks up.
Detach the Camera Flash.
3● Press the button and
rotate the hotshoe fixing
buckle to the left until it is
loosened.
Power Management
Use ON/OFF Power Switch to power the flash unit on or off. Turn
off if it will not be used for an extended period of time. Setting as a
master flash, it will turn the power off automatically after a certain
period (approx. 90 seconds) of idle use. Pressing the camera
shutter halfway or pressing any flash button will wake up the flash
unit. Setting as a slave flash, it will enter sleep mode after a certain
period (adjustable, 60 minutes by default) of idle use. Pressing any
flash button will wake it up.
The battery level is going to be used out
immediately. And the flash will auto power off
in 1 minute.
Note: Please recharge the battery as soon as
possible (within 10 days). Then, the battery can be
used or be placed for long period.
Meaning
Full
Middle
Low
Lower battery, please recharge it.
LED Modeling Lamp
Press the Modeling Lamp Setting button to set the modeling
lamp. Short press the Set Button to turn on or off the modeling
lamp. When turning the modeling lamp on, turn the select dial
to set its brightness. There are 10 levels(01~10) for choice.
- 37 - - 38 -
Flash Mode—TTL Autoflash
This flash has three flash modes: TTL, Manual (M), and Multi
(Stroboscopic). In TTL mode, the camera and the flash will work
together to calculate the correct exposure for the subject and the
background. In this mode, multiple TTL functions are available:
FEC, HSS, second curtain sync, modeling flash, control with the
camera’s menu screen.
* Press < MODE > Mode Selection Button and three flash modes
will display on the LCD panel one by one with each pressing.
TTL Mode
Press < MODE > Mode Selection Button to enter TTL mode. The
LCD panel will display.
● Press the camera release button halfway to focus. The aperture
and effective flash range will be displayed in the viewfinder.
● When the shutter button is fully pressed, the flash will fire a pre-
flash that the camera will use to calculate exposure and flash
output the instant before the photo is taken.
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.
It is useful in situations where minor adjusting of the TTL system is
needed based on the environment.
FEC: Flash Exposure Compensation
Setting FEC:
Set the flash exposure
2compensation amount.
● Turn the Select Dial to set
the amount.
● To cancel the flash
exposure compensation,
set the amount to “+0”.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
Press Set Button again to
3confirm the setting.
Press Function Button 2
1Press the <+/-> button. The
icon < > and flash
exposure compensation
amount will be highlighted on
the LCD panel.
C.Fn
C.Fn
Disabling Auto Power Off function is recommended when
the flash is used off camera. (C.Fn-STBY, Page 52)
Slave Auto Power Off Timer is set to 60 minutes by
default. Another option “30 minutes” is available. (C.Fn-
Sv STBY, Page 52)
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● If you set a shutter speed that is the same as or slower than
the camera’s maximum flash sync speed, < > will not be
displayed in the viewfinder.
● To return to normal flash, press < > button again. Then
< > will disappear.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all
camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
Choose REAR flash mode in Sony camera setting.
Press Function Button 2
1< > so that < > is
displayed.
Check that < > is
2displayed in the viewfinder.
SYNC
SYNC
- 39 - - 40 -
The flash output is adjustable from 1/1 full power to 1/256th power
in 1/10th stop increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
M: Manual Flash
Press < MODE > button so
1that < M > is displayed.
Press the <+/-> button and turn
2the Select Dial to choose a
desired flash output amount.
Press Set Button again to
3confirm the setting.
Optic S1 Secondary Unit Setting
In M manual flash mode, press <S1/S2> button so that this flash can
function as an optic S1 secondary flash with optic sensor. With this
function, the flash will fire synchronously when the main flash fires,
the same effect as that by the use of radio triggers. This helps create
multiple lighting effects.
Optic S2 Secondary Unit Setting
Press <S1/S2> button so that this flash can also function as an optic
S2 secondary flash with optic sensor in M manual flash mode. This
is useful when cameras have pre-flash function. With this function,
the flash will ignore a single “preflash” from the main flash and will
only fire in response to the second, actual flash from the main unit.
● S1 and S2 optic triggering is only available in M manual
flash mode.
● After you finish the setting,
press Set Button and all the
settings will be displayed.
Turn the Select Dial to
3choose a desired flash
output.
Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1that < > is displayed.
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
Calculating the Shutter Speed
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
● If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
● Stroboscopic flash can be used with“buLb”.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● A flash output of 1/1 and 1/2 cannot be set for stroboscopic
flash.
MULTI
Set the flash frequency and
2flash times.
● Press the Function Button
3 <Hz> to select the flash
frequency. Turn the Select
Dial to set the number.
● Press the Function Button
2 <Times> to select the
flash times. Turn the Select
Dial to set the number.
- 41 - - 42 -
Hz
Maximum Stroboscopic Flashes:
Flash
output
Hz
Flash
output
Wireless Flash Shooting: Radio (2.4G) Transmission
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
● The V1S attach to the camera is called the master unit, and
a V1S that is wirelessly controlled is called the slave unit.
● You can also wirelessly control the V1S set as the slave unit
with the transmitter X1T-S or XProS (sold separately). For
details on setting the master unit functions, see the
transmitter’s instructions.
1/4
1/8
1/16
1/32
1/64
1/128
1/256
1
8
14
30
60
90
90
90
2
6
14
30
60
90
90
90
3
4
12
30
60
90
90
90
4
3
10
20
50
80
90
90
5
3
8
20
50
80
90
90
6-7
2
6
20
40
70
90
90
8-9
2
5
10
30
60
80
80
1/4
1/8
1/16
1/32
1/64
1/128
1/256
10
2
4
8
20
50
70
70
20-50
2
4
8
16
30
40
40
60-100
2
4
8
12
20
40
40
Positioning and Operation Range (Example of wireless flash
shooting)
● Autoflash Shooting with One Slave Unit
● Before shooting, perform a test flash and test shooting.
● Use the supplied mini stand to position the slave unit.
● The transmission distance might be shorter depending on
the conditions such as positioning of slave units, the
surrounding environment and whether conditions.
Transmission distance is about 100m.
● Auto Shooting with Two Slave Groups
● Auto Shooting with Three Slave Groups
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 4 groups.
Wireless Multiple Flash Shooting
A
B
A
B
C
- 43 - - 44 -
Slave Unit Setting
Master Unit Setting
Press < > button so that < >
is displayed on the LCD panel.
Press < > button so that < >
or < > are displayed on
the LCD panel.
2. Group Mode Selection
The function button 1/2/3/4
1can can control the group
M/A/B/C. Short press
function button can select
TTL/M/OFF. Choose one of
them as the flash mode of
the master unit.
Press <MODE> button to
2switch to Multi mode.
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
1. Wireless Settings
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Press <MENU> Button to
1enter C.Fn CH setting.
In C.Fn CH, turn the Select
2Dial to choose channel ID
from 1 to 32.
Press the Set Button to
3confirm.
4. Wireless ID Settings
Change the wireless channels and wireless ID to avoid interference
for it can only be triggered after the wireless IDs and channels of the
master unit and the slave unit are set to the same.Press the <MENU>
button to enter C.Fn ID. Press the Set Button to choose OFF channel
expansion shutdown, and choose any figure from 01 to 99.
C.Fn Ver 0.5
CLEAR
CH
ID
BEEP
STBY
07
SCAN
5. Scan the Spare Channel
To avoid the interference of using the same channel by others, this
function can be used: enter the C.Fn settings and find the SCAN
option. When setting it to START, it will scan from 1% to 100%. And
the 8 spare channels will be displayed after the scan is completed.
6. TTL：Fully Automatic Wireless Flash Shooting
Using Automatic Wireless Flash with a Single Slave Unit
● M/A/B/C can be set to TTL
separately.
Master Unit Setting
1● Attach a camera V1S
flash on the camera and
set it as the master unit.
- 45 - - 46 -
C.Fn Ver 0.5
CLEAR
CH
ID
BEEP
STBY
99
SCAN
C.Fn Ver 0.5
CLEAR
CH
ID
BEEP
SCAN
22 08 32 23
30 21 07 06
as the wireless slave Unit.
Slave Unit Setting
2● Set the other camera flash
● If the master unit and slave
unit(s) are set to a different
channel, set them to the
same channel. (Page 46)
Check the communication
3channel.
● Check that the master flash
ready indicator is lightened.
Check that the flash is
5ready.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
Test Button < >.
Check the flash operation.
6● Press the master unit’s
Position the camera and
4flashes.
● Position the camera and
flashes as the picture
shows. (Page 44)
Using Automatic Wireless Flash with Multiple Slave Units
When the number of slave units is
increased and the master unit
flash firing is ON, automatic
control is implemented to make all
groups of flashes fire the same
flash output and ensure the total
flash output up is to standard
exposure.
When stronger flash output or
more convenient lighting operation
is needed, increase the number of
slave units and set it as a single
slave unit.
To add slave units, use the same
steps as setting “automatic
wireless flash with a single slave
unit”. Any flash group can be set
(A/B/C/D/E).
● If the slave unit’s auto power off function is workable, press the master
unit’s test button to power it on. Please note that test firing is unavailable
during the camera’s regular metering time.
● The effective time of slave auto power off is changeable. (C.Fn-Sv STBY
Page 55)
Using Fully Automatic Wireless Flash
The FEC and other settings that set on the master unit will also be
appeared on the slave unit automatically. The slave unit does not
need any operation. Use the following settings to make wireless
flashes according to the same methods with normal flash shooting.
● Flash Exposure Compensation ( Page 39)
About Master Unit
Use two or more master units. By preparing several cameras that
with master units flash attached, cameras can be changed in
shooting while keeping the same lighting source (slave unit).
- 47 - - 48 -
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
7. M: Wireless Flash Shooting with Manual Flash
Setting the flash mode to
1<M>.
Taking the picture.
3
Setting <M> Flash Mode
You can directly operate the slave unit to manually set the manual
flash or stroboscopic flash.
Setting the slave unit.
1
that <M> is displayed.
Setting flash mode to <M>.
2● Press <MODE> button so
● Set the manual flash
output. (Page 41)
< >. Turn the Select
Dial to set the flash output
of the groups. Press Set
Button to confirm.
Setting flash
2output.1/2/3/4<M/A/B/C>
● Press Function Button 3
Gr
● Each group fires at the set
flash ratio.
8. Multi: Wireless Flash Shooting with Manual Flash
Setting <MULTI> stroboscopic
flash.
● Setting the stroboscopic flash.
(Page 42)
● Press <MODE> button so that
<MULTI> is displayed.
SONY
CH 21
Other Applications
Sync Triggering
The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here
and the flash will be fired synchronously with the camera shutter.
Auto Focus Assist Beam
In poorly-lit or low-contrast shooting environments, the built-in auto
focus assist beam will automatically light on to make it easier for
autofocus. The beam will light up only when autofocus is difficult
and get out as soon as the autofocus becomes correct.
If you want to turn off the auto focus assist beam, set the “AF” to
“OFF” on the C.Fn settings.
● Camera models that support auto focus assist beam:
α7M3/α7R3/α7II/α7/α6000/α9
● If you find the auto focus assist beam does not light up, this
is because the camera has got a correct autofocus.
Position
Center
Periphery
Effective Range
0.6~10m / 2.0~32.8 feet
0.6~5m / 2.0~16.4 feet
- 49 - - 50 -
Altri manuali per V1S
2
Indice
Altri manuali Godox Accessori per fotocamere
Godox
Godox X1C Manuale utente
Godox
Godox PT-16 Manuale utente
Godox
Godox X1 Manuale utente
Godox
Godox XProF Manuale utente
Godox
Godox X1N Manuale utente
Godox
Godox QE Series Manuale utente
Godox
Godox LR150 Manuale utente
Godox
Godox SL100Bi Manuale utente
Godox
Godox RING 48 Manuale utente
Godox
Godox LED500L Manuale utente
Godox
Godox UTR Manuale utente
Godox
Godox V860IIIN Manuale utente
Godox
Godox X1R-N Manuale utente
Godox
Godox V1C Manuale utente
Godox
Godox K-150A Manuale utente
Godox
Godox X1 Manuale utente
Godox
Godox Parabolic 66 Manuale utente
Godox
Godox SEII Manuale utente
Godox
Godox XProO Manuale utente
Godox
Godox SL Series Manuale utente
