Godox X1C Manuale utente

TTL无线引闪器

TTL Wireless Flash Trigger

For Canon

说明手册

Instruction Manual

中英文双语

Chinese English Bilingual

705-X1C000-00 Made In China

地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋

Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong

Town, Baoan District, Shenzhen 518103, China

电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423

邮箱/E-mail: [email protected]

深圳市神牛摄影器材有限公司

GODOX Photo Equipment Co., Ltd

- 19 -

型号

TTL控制

辅助对焦

频闪闪光

后帘同步

造型闪光

无线闪光

无线功能

X1C

手动开启

有

有，使用相机的景深预视按钮进行闪光

TTL模式下，Ratio Off

M模式下，光比闪光(A:B C)

支持GR分组闪光(A~E组可以分别设置闪光模式)

可控从属单元组

传输范围(约)

频道

其他

时延设置

无线快门

ZOOM设置

显示屏

输出接口

固件更新

记忆功能

发射器尺寸/净重

接收器尺寸/净重

GR 分组模式下，最多5组(A/B/C/D/E)

Ratio光比分组模式下，3组(A/B/C)

>100米

32个

有(0~10ms，以100us为单位设置)

接收器端可以通过2.5mm同步接口控制相机拍摄

可以通过发射器调节闪灯焦距值

宽屏液晶显示，背光开启或关闭

发射器：PC 端子输入、输出；接收器：2.5mm同步线输出

通过机身上的 Micro USB进行固件升级

设置2秒后的参数会自动记忆，重新开机自动恢复

72x75x52(mm)/100g

70x65x47(mm)/70g

- 20 -

Foreword

For Your Safety

Names of Parts

Body

LCD Panel

Accessories

Battery

Installing Batteries

Low Battery Level Indication

Using the Flash Trigger

As a Wireless Studio Flash Trigger

As a Wireless Speedlite Trigger

As a Wired Shutter Release

As a Wireless Studio Flash Trigger

or Speedlite

Trigger with PC Sync Socket

Setting the Transmitter

Power Switch

Power Switch of AF Assist Beam

Channel Settings

Mode Settings

Current Group Settings

Multi Flash Settings (Times & Frequency)

Multi Flash Settings (Output Value)

Group Settings

Test Flash

Setting GR Grouping Mode

Automatically Enter Power Saving Mode

C.Fn: Setting Custom Functions

Wireless Shutter Release Mode

Setting the Camera

Setting the Receiver

Channel Settings

Group Settings

Automatically Enter Power Saving Mode

Attentions

Caring for Flash Trigger

Technical Data

Contents

Foreword

Thanks for your purchase of this X1C TTL wireless flash trigger.

This TTL wireless flash trigger can be used with a transmitter and one or more receivers for

studio flash, speedlite, and camera shutter. Featuring multi-channel triggering, stable signal

transmission, and sensitive reaction, it gives photographers unparalleled flexibility and

control over their strobist setups. The flash trigger applies to hotshoe-mounted Canon EOS

series cameras, as well as the cameras which have PC sync sockets.

With X1C wireless flash trigger, high speed synchronization is available for most of camera

flashes in the market which support E-TTL II. The max flash synchronization speed is up to

1/8000s *.

*: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s. 1/8000s is not

achievable because some models of Canon EOS cameras have a max camera shutter speed of only 1/4000s.

- 21 -

For Your Safety

- 22 -

To prevent damage to your product or injury to you or to others, read the following safety

precautions in their entirety before using this device. Keep these safety instructions where

all those who use this device will read them.

Failure to observe the precautions listed in this section could result in damage to the

product.

The following icon indicates warnings that should be read before using this device in case

of possible damage or injury.

Do not disassemble or modify

Failure to observe this precaution could result in electric shock or product malfunction.

Should the product break open as the result of a fall or other accident, remove the

batteries and take the product to an authorized maintenance center for inspection.

Keep dry

Do not handle with wet hands or immerse in or expose to water or rain. Failure to

observe this precaution could result in fire or electric shock.

Do not use in the presence of flammable gas

Failure to observe this precaution could result in explosion or fire.

Keep out of reach of children

This device contains small parts which may pose a choking hazard. Consult a

physician immediately if a child swallows any part of this device.

Turn off the transceiver immediately in the event of malfunction

Should smoke or an unusual smell comes from this device, remove the batteries

immediately in case of burning and take the device to an authorized maintenance

center for inspection. Injuries could occur if it is further used.

Do not expose to high temperature

Do not leave the device in a closed vehicle in the sun or in other areas subject to

For Your Safety

- 23 -

extremely high temperature. Failure to observe this precaution could result in fire or

damage to the casing or internal parts.

Observe precautions when handling batteries

Batteries may leak or explode if improperly handled. Observe the following precautions

when handling batteries for use in this device:

Use only batteries listed in this manual. Do not use old and new batteries or

batteries of different types at the same time.

Read and follow all warnings and instructions provided by the manufacturer.

Batteries cannot be short-circuited or disassembled.

Do not put batteries into a fire or apply direct heat to them.

Do not attempt to insert batteries upside down or backwards.

Batteries are prone to leakage when fully discharged. To avoid damage to the

product, be sure to remove batteries when the product is not used for a long time or

when batteries run out of charge.

Should liquid from the batteries come into contact with skin or clothing, rinse

immediately with fresh water.

MODE Mode Selection Button

CH Channel Setting Button

GR Group Setting Button

Select Dial

Hot Shoe Camera

Connection

LCD Panel

Names of Parts

- 24 -

Transmitter

Power Switch

--ON (Power On)

--OFF (Power Off)

AF Assist Beam Switch

--ON(AF Assist Beam outputs)

--OFF(AF Assist Beam do

not output)

Status Indicator Lamp

--LED Red Color Lamp

TEST Trigger Button

--Half Press

--Fully Press

Micro USB Port

PC Sync Socket

Battery

Compartment

Hot Shoe Speedlite

Connection

Body

GRCH

Names of Parts

2.5mm Shutter

Release Port

Receiver

TEST Trigger Button

Power Switch

--ON (Power On)

--OFF (Power Off)

Status Indicator Lamp

--LED Red Color Lamp

CH Channel Setting Button

GR Group Setting Button

LCD Panel

Hot Shoe Speedlite

Connection

Micro USB Port

Battery

Compartment

- 25 -

Names of Parts

(A) Group Setting (B) Channel Setting (C) Low Battery Indicator

Receiver Panel

- 26 -

(A) Output Settings per Group in the M Mode; FEC Settings per Group in the TTL Mode

(B) Mode Settings (C) Group (D) Currently Selected Group (E) Channel Settings

(F) GR Grouping Icon (G) Synchronization Delay Setting Icon (H) Low Battery Indicator

(I) Single Contact Icon

Transmitter Panel

Installing Batteries

As shown in the illustration, slide the battery compartment lid of the transmitter and

receiver and insert two AA batteries (sold separately)separately.

Low Battery Indication

When the battery power (2 AA

batteries <2.0V) gets low,

Status Indicator Lamp blinks

quickly (blink cycle=0.5s).

Please replace new batteries,

as low power leads to no flash

or flash missing in case of

long distance.

Battery

- 27 -

Names of Parts

1. Remote Cable(C1, C3) 2. Sync Cable 3.Sync Adapter

Accessories

1. As a Wireless Studio Flash Trigger

1.1 Mount the transmitter on camera hotshoe and turn it

on before turning on the camera.

1.2 Connect the receiver to studio flash by Sync Cable

(one end in 2.5mm Shutter Release Port of the

receiver, the other end in sync port of studio flash)

before turning on the studio flash.

1.3 Set the transmitter and the receiver to the same

channel.

1.4 Press the camera shutter button, and the studio

flash will be triggered simultaneously. Status

Indicator Lamp of both transmitter and receiver

units turn red.

The flash trigger features the following functions:

Using the Flash Trigger

2. As a Wireless Speedlite Trigger

2.1 Mount the transmitter on camera hotshoe and turn it

on before turning on the camera.

2.2 Mount the speedlite to Hot Shoe Speedlite

Connection of receiver unit. Set the speedlite to M

mode.

2.3 Set the transmitter and the receiver units to the

same channel.

2.4 Press the camera shutter button, and the speedlite

will be triggered simultaneously. Status Indicator

Lamp of both transmitter and receiver units turn red.

- 28 -

3. As a Wired Shutter Release

3.1 Connect the receiver and the camera by Remote

Cable (one end in receiver’s Shutter Release

Port, the other end in camera’s shutter port)

before turning on the camera.

3.2 Half press the <TEST> Trigger Button to focus.

When fully press the <TEST> Trigger Button to

shoot, the Status Indicator Lamp will turn red until

releasing the button.

Using the Flash Trigger

4. As a Wireless Studio Flash Trigger or Speedlite

Trigger with PC Sync Socket

4.1 The connection method of the receiver can be

found in As a Wireless Studio Flash Trigger and As

a Wireless Speedlite Trigger section.

4.2 The transmitter will control the flash on the

receiver end to fire via using PC Sync Socket as

input by default.

4.3 Press the camera shutter and use the PC Sync

Socket’s signal to control the flash.

4.4 PC Sync Socket can also be set as output. Long

press the <CH> Button of the transmitter until

<Fn> is displayed on the panel. Then, set the

value of Fn 03 to 1, and the PC Sync Socket is

under output mode.

- 29 -

Setting the Transmitter

Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink.

Note: In order to avoid power consumption, turn off the transmitter when not in use.

Power Switch

Slide the power switch to ON, and the AF lighting is allowed to output.

Power Switch of AF Assist Beam

Channel Setting

1. Short press the <CH> Button until the

channel amount blinks.

2. Turn the Select Dial to choose the

appropriate channel. Press the <CH> Button

again to confirm the setting.

3. This flash trigger contains 32 channels

which can be changed from 1 to 32. Set the

transmitter and the receiver to the same

channel before usage.

- 30 -

Setting the Transmitter

Mode Setting

1. Short press the <MODE> Button, and the

mode of the current group will change.

2. To NON-GR grouping mode, all the groups’

modes will be changed simultaneously by

the order of TTL/M/Multi, in accordance

with Ratio flash mode. To GR grouping

mode, only the current group’s mode will

be changed by the order of TTL/M/--.

Current Group Settings

1. Short press the <GR> Button to set the

current group.

2. The current group settings will blink and

turn the Select Dial to change the settings.

3. When the current group is in the M mode,

the power output value is changeable from

1/1 full power to Min.[Note 1] power in 0.3

stop increments. When the current group

is in the TTL mode, the FEC amount is changeable

from -3 to 3 in 0.3 stop increments. When the current group is in the -- mode (flash

off), the amounts will not change.

4. Short press the <GR> Button again to confirm the setting.

- 31 -

Multi Flash Settings (Times & Frequency)

1. In the multi flash (TTL and M icon are not

displayed), long press the <MODE> Button to

enter multi flash setting submenu.

2. The two lines are separately displayed as T

(flash times) and H (flash frequency).

3. Short press the <GR> Button to choose the

related setting amounts. Turn the Select Dial

to change the blinking settings.

4. Continue to short press the <GR> Button, and the blinking settings on the next line can

be changed.

5. Until all the amounts are set. Short press the <MODE> Button to exit the setting status.

6. In the multi flash setting submenu, short press the <MODE> Button to return to main

menu.

Multi Flash Settings (Output Value)

1. In the multi flash (TTL and M icon are not

displayed), short press the <GR> Button to

set the current group.

2. In multi flash mode, the power output will be

changed from Min. to 1/4.

Setting the Transmitter

- 32 -

[Note 1]

Min. refers to the minimum power output value that can be set in M/Multi mode.

X1C's minimum power output value is 1/128 for most of camera flashes. However, the value can

change to 1/256 when using in combination with Godox strong power flashes e.g. AD600, AD360II, etc.

Note: As flash times are restricted by flash output value and flash frequency, the flash times

cannot surpass the upper value that permitted by the system.

The times that transported to the receiver end are a real flash time, which is also related to the

camera's shutter setting.

Setting the Transmitter

Group Settings

1. Long press the <GR> Button to set all the groups that in the same modes

simultaneously.

2. The settings of the groups which are in the same mode with the current group will

blink. Turn the Select Dial to change the settings.

3. If the current group is in the M mode, all the other groups which are in the M mode will

change their power output value simultaneously. The power output value is

changeable from 1/1 full power to Min. power in 0.3 stop increments, until one of the

group’s setting turns to the maximum(1/1) or the minimum(Min.). If the current group

is in the TTL mode, all the other groups which are in the M mode will change their

FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop

increments, until one of the group’s setting turns to the maximum(3) or the minimum(-

3). If the current group is in the -- mode (flash off), the amounts will not change.

4. Short press the <GR> Button again to confirm the setting.

- 33 -

Setting the Transmitter

Test Flash

5. The settings on the transmitter end will synchronize to the receiver end at the same

time.

1. Press the <TEST> Trigger Button to see the

whether flash will fire normally or not.

2. Fully press the <TEST> Trigger Button, and

the Status Indicator Lamp turns red and the

flash on the receive end can be triggered.

3. Use the transmitter to control camera to

focus or shoot, and the transmitter is

connecting to the camera (do not connect to

the flash) now.

4. In the standby mode, press the TEST

Button can wake up the receiver.

- 34 -

Setting GR Grouping Mode

Note: GR mode can only be used normally when attaching to the CANON EOS cameras that

issued after 2012. In the GR mode, multi flash cannot be set.

1. Press the <MODE> Mode Button until Gr

icon is displayed, which shows that GR

grouping mode has been set.

2. To cancel GR grouping mode, press the

<MODE> Button again until the Gr icon

disappeared.

Setting the Transmitter

Automatically Enter Power Saving Mode

1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and

the displays on the LCD panel will disappear.

2. Press any of the button (<TEST> fully pressed/<CH>/<GR>/<MODE>) can wake up

the flash trigger. If the transmitter is attached to the CANON EOS camera, half press

the shutter can also wake up the system.

3. If the transmitter is set to single contact mode( isdisplayed), the system will not

enter power saving mode.

The following table lists the available and unavailable custom functions of this flash. The

icon“√”indicates the flash custom function is supported but “0”indicates the custom

function is not supported.

Settings and Description

OFF

Master flash synchronization delay N*100 us

(synchronization delay icon is displayed.)

OFF

ON(The single contact mode set icon

is displayed.)

Setting Signs

1~100

Functions

Synchronization

delay setting

Single contact

mode

Custom

Functions No.

C.Fn-00

C.Fn-01

Application

√

- 35 -

C.Fn: Setting Custom Functions

Setting the Transmitter

- 36 -

Settings and Description

It is advisable to set the transmitter to single

contact mode when using it to trigger the flash

by PC cord or through camera’s single contact.

Do not change the zoom value.

Changing with camera's zoom value.

Zoom(20/24/28/35/50/70/80/105/135/

200mm)

PC sync socket connects with camera

PC sync socket connects with flash

Second curtain sync off

Second curtain sync on

1/128

1/256(displayed as 1/128-)

Setting Signs

20,24,28,35,50,70,

80,105,135,135+

Functions

Single contact

mode

Zoom setting

PC sync socket

connects with

camera/flash

Second curtain

sync [Note 2]

Minimum power

output value in

M/Multi mode

Custom

Functions No.

C.Fn-01

C.Fn-02

C.Fn-03

C.Fn-04

C.Fn-05

Application

√

[Note 2]:

Second curtain sync cannot be set through the camera's external flash functions setting.

When using second curtain sync, the effective shutter speed range is from 1/30s to 30s. When shutter speed

is set as buLb or is quicker than 1/30s, the settings are invalid.

After being turned on, second curtain sync is effective even though HSS has been set and the shutter speed

range is from 30s to 1/30s.

After second curtain sync is turned on, synchronization delay settings are invalid.

√

Altri manuali per X1C

Indice

Manuali Accessori per fotocamere popolari di altre marche

Viltrox

Viltrox EF-NEX Istruzioni per l'installazione

Calumet

Calumet 7100 Series CK7114 Manuale utente

Ropox

Ropox 4Single Series Manuale utente

Cambo

Cambo Wide DS Digital Series Istruzioni operative

Samsung

Samsung SHG-120 Manuale utente

Ryobi

Ryobi BPL-1820 Manuale operativo

Aegis

Aegis ABL-36020P Manuale utente

Pentax

Pentax Data Back Fc Manuale utente

Fantasea

Fantasea EyeGrabber F Series Manuale utente

Honeywell

Honeywell HDZ20HD Manuale utente

EGO

EGO BA1400T Manuale utente

Sima

Sima SRW-62 Manuale utente

Shape

Shape A7SSMKIT Manuale utente

Slide Kamera

Slide Kamera HST-2 Manuale utente

Power works

Power works 2902613 Manuale utente

SES

SES SE-2047-2 Manuale utente

Olympus

Olympus PT-EP05L Manuale utente

Starlite

Starlite OctoDome nxt Manuale utente