Goldmund SR2.3 Manuale utente

GOLDMUND SR2.3

2 CHANNEL POWER AMPLIFIER

GOLDMUND SR2.3

2 CHANNEL AMPLIFIER

USER MANUAL

ATTENTION :

No connection or manipulation must be done before reading those instructions. Damage to the

amplifier may result if the following instructions are not consciously understood and applied.

1 - UNPACKING

You will find in the GOLDMUND SR2 box :

- The amplifier.

- The power cord.

- This manual and the warranty card.

- Accessories and spare fuses.

Please keep the packaging in case you need to transport the amplifier at a later date or if you have to

send it for maintenance.

2 - CHOICE OF AMPLIFIER LOCATION AND COOLING

The GOLDMUND SR2.3 amplifier, as all the high quality amplifiers may generate a large amount of

heat if driven into high power.

It is mandatory to allow a proper cooling of the heat sink. Avoid any location which is not properly

ventilated and avoid putting other equipment on top of the amplifier.

3 - LINE VOLTAGE ADJUSTMENT

An AC line voltage selection is possible inside the chassis. Please ask your dealer for assistance if the

line voltage provided is not appropriate.

ATTENTION : On the 220V position, the GOLDMUND SR2.3 amplifier will function properly for AC

voltages in between 200V and 245V. On the 110V position, the AC line must deliver between 95V and

125V. If your AC line is usually out of these tolerances, please consult your GOLDMUND dealer.

Please check the value of the mains line fuse. This fuse is located in the power cord receptacle. The

lid can be removed with a small screwdriver when the cord is removed.

Use a 5A slow-blow fuse for 220V and a 8A slow-blow fuse for 110V.

4 - CONNECTIONS

Check if volume control is down to zero on the preamplifier or the 5 channel processor.

First, connect the interconnects between the preamp/processor and each of the power amps inputs.

Connect the speaker cables to the red and black terminals accessible at the back of the amplifiers.

You may notice that the ground of the input and the black speaker terminal are of the same polarity.

The amplifier is non-inverting in phase.

Then, connect the power cords to the back of the amplifier and plug it in the nearest wall plug. Use a 3

lugs grounded plug, for safety reasons. To get the best sound of the amplifier, avoid any multiple plug

or extension cord.

The switch marked inputs link is connecting the 2 inputs together if the amp is to be used with a

monaural source or for bi-amping.

5 – AMPLIFIER CONTROLS

On the front plate of the GOLDMUND SR2.3 amplifier you will find only one switch : The POWER key,

used to power the amp on and one power led.

When turned ON the 2 channels are immediately connected and the front panel POWER led lights up.

The amp may be powered off by turning off the POWER switch at any time. The led will fade very

slowly, indicating discharge of the filter capacitors. The speakers will be disconnected after a few

seconds.

It is absolutely normal that a slight sound is heard from the speakers when the amplifiers are turned

ON or OFF. The SR2.3 is self-protected and the sound heard is corresponding to the charging and

discharging of the capacitors.

6 - SOUND QUALITY OPTIMIZATION

- Warm-up sonic effect.

If the power amplifier has not been powered on for a few days, the optimum sound quality is reached

after 15 minutes. This delay has been optimized to be minimal and the sonic quality when just

powered on is much higher than other quality power amplifiers.

- Speaker polarity.

Even if you have an absolute phase inverter on your preamplifier (as on the Goldmund SR2.3,

Mimesis 27+ or Mimesis 22M), and even if you have carefully selected the proper line phase (see in

next paragraph), there is a possibility to again increase the sonic quality of your speakers by reverting

the polarity of each speaker cable at amp termination. But since the line phase and the speaker

polarity interfere to each other, you have to experiment carefully all the combinations before picking

the right one.

If your preamplifier has an absolute phase inverter, this will interfere too. If it has not, don't forget the

result will depend of the source, most of the record and CD being recorded without care for the

absolute phase. Be patient…

- Mains line phase inversion.

The sonic quality of your GOLDMUND SR2.3 can be greatly improved if the mains AC line is properly

connected. Try to invert the AC plugs of both your amplifiers, using special adapters.

We recommend that you proceed carefully to try this. You must do it in combination with the speaker

polarity and/or with absolute phase switching to be sure of the best result.

7 - SAFETY AND PRECAUTIONS

Attention :

The GOLDMUND SR2 is an extremely high speed amplifier.

Any bad ground connection can generate high frequency oscillation which is dangerous for tweeters.

It is also generally dangerous to run input cable and speaker cables in parallel for a long distance. If

these cables are not of high quality or badly shielded, an “Antenna-Effect” can generate dangerous

high-frequency oscillations.

- Protection against DC.

The GOLDMUND SR2.3 is a DC-coupled amplifier. Without protection and if the associated

preamplifier is badly designed or defective (often true for tube preamps and some 5 channel

processors), the speakers could easily be damaged by the amplified DC.

The SR2.3 protects itself from such an accident by a feedback DC control that limits the DC amplified

by the circuit.

This protection circuit is totally transparent and has no sonic effect.

- Protection against short-circuits.

If one output is short-circuited by accident the amplifier is self-limiting its output so the current doesn’t

become too high.

However, such accident should be limited in time to avoid excessive heat-up to occur. In extreme

cases, such mishandling could destroy the amplifier, which is not covered by the warranty.

There is no risk to leave the speaker terminals unconnected when the amps are on.

8 - MAINTENANCE

The GOLDMUND SR2.3 amplifier usually requires no maintenance. For the audio purists who want to

keep their amp sounding as new, we only recommend that after a year or two, you have a technician

or an official GOLDMUND representative readjust the DC offset. This very simple operation takes only

two minutes and will give you the safety of long years of unmatched sound quality.

To clean your SR2.3 use only a soft cloth slightly damp. Always turn the power off before cleaning

your amplifier.

TECHNICAL DATA

POWER

- Nominal power before clipping: 2x200 W RMS (2 - 8 Ohms). 150 W RMS (1 - 16 Ohms).

- Maximum power : > 400 W RMS (3 Ohms).

- Maximum voltage : 55 V peak. - Maximum current : > 15 A peak.

These values for all channel driven

FREQUENCY RESPONSE

These figures are valid for the circuit alone, at any level between 0 and nominal power.

- +/- 0.1 dB, 10 Hz - 1 MHz.

- +/- 1 dB, 6 Hz - 1.2 MHz.

- +/- 3 dB, 3 Hz - 1.4 MHz.

INPUT SENSITIVITY

- Nominal level : 0.75 V.

- Input impedance : 50 kOhms.

GROUP DELAY

Propagation delay < 100 ns stable with frequency from DC to 200 kHz.

DISTORTION

Figures valid for all levels from 0 to 20 V / 8 Ohms.

- Dynamic : TID < 0.01 % (- 80 dB).

- Static : THD < 0.01 % (- 80 dB).

SPEED

- Slew rate : > 240 V/us

- Rise time : < 260 ns.

NOISE

- Weighted ASA A : > 100 dB.

OPERATING TEMPERATURE

- Room temperature : -30 to +40 degrees Celsius ( -22 to +104 degrees Fahrenheit).

- Internal temperature : +45 to +65 degrees Celsius ( +113 to +149 degrees Fahrenheit).

POWER SUPPLY

- Nominal line voltage : 117 or 234 V.

- Input voltage range : +/- 15 %.

- Maximum power consumption : 450 W.

SIZE AND WEIGHT

- 44 cm W x 33 cm D x 9 cm H. - Weight : 13 kg net.

WARRANTY

- 3 years parts and labor.

Indice

Altri manuali Goldmund Amplificatore

Goldmund

Goldmund METIS 2 Manuale utente

Goldmund

Goldmund MIMESIS 27.3 Manuale utente

Goldmund

Goldmund TELOS 3500 Manuale utente

Goldmund

Goldmund TELOS 280 Manuale utente

Goldmund

Goldmund SRM250 Manuale utente

Goldmund

Goldmund TELOS 390.5 Manuale utente

Goldmund

Goldmund TELOS 390 Manuale utente

Goldmund

Goldmund TELOS 350 Manuale utente

Goldmund

Goldmund Amplifiers Manuale utente

Goldmund

Goldmund MIMESIS 16 Manuale utente

Goldmund

Goldmund GOLDCUBE Manuale utente

Goldmund

Goldmund TELOS 590 NextGen Manuale utente

Goldmund

Goldmund MIMESIS 22 HISTORY Manuale utente

Goldmund

Goldmund TELOS 400 Manuale utente

Goldmund

Goldmund SRP2.3 Manuale utente

Goldmund

Goldmund MIMESIS SRM2.3 Manuale utente

Goldmund

Goldmund PH7.3 Manuale utente

Goldmund

Goldmund SRI2 Manuale utente

Goldmund

Goldmund SR8 Manuale utente

Goldmund

Goldmund MIMESIS 18.4 Manuale utente

Goldmund

Goldmund Mimesis PH2 Manuale utente

Goldmund

Goldmund TELOS 200 Manuale utente

Goldmund

Goldmund PH3 Manuale utente

Goldmund

Goldmund MIMESIS 22 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente