SW1
P1
Add user cards (Master):/ key tags set DIP switch 2 to ON, the LED on the front will blink (red). Then
wave the new NFC/US cards (Golmar) that you wish to add over the proximity reader one by/ key tags
one, the module will emit 2 tones and the LED will light up (green) for one second every time a Master
proximity card is memorised or the LED will blink rapidly (red) if the card has already/ key tag / key tag
been memorised.
Up to 30 Master cards can be memorised. Assigning a group of cards/ key tags residents / key tags and
(one-access visiting and multi-access visiting) to each Master card is for advancedcards / key tag
configuration and management of the access control (mobile with NFC and AC Manager app
required, Android only), TAC Manager manual (code 50124945).see the
To exit 'Add Master cards ' mode, set DIP switch 2 to OFF, the LED on the front (red) will turn/ key tags
off.
Basic configuration of the access control with the Master card ./ key tag
It enables the adding/removing of Master (one-accessand residents' access cards/ key tags and
and multi-access) and Installation cards.
Important: First of all, the Master card(s) need to be added with the SW1 DIP switch./ key tag(s)
Once the Master cards have been added, the rest of the cards will be added./ key tags / key tags
Add access ( one-access and multi-access) and Installation cards:residents' cards/ key tags and
-Step 1: Wave a Master card over the proximity reader, the LED on the front will light up (red)./ key tag
-Step 2: Wave the new NFC/US cards (Golmar) that you wish to add over the proximity reader one by one,/ key tags
the module will emit 2 tones and the LED will light up (green) for one second every time a Residents' access card/
key tag / key tagis memorised or the LED will blink rapidly (red) if the card has already been memorised.
-Step 3: Wave the Golmar NFC/1U one-access Visiting cards that you wish to add over the proximity reader one by
one, the module will emit 2 tones and the LED will light up (green) for one second every time a one-access Visiting
card is memorised or the LED will blink rapidly (red) if the card has already been memorised.
-Step 4: Wave the Golmar NFC/MU multi-access Visiting cards that you wish to add over the proximity reader one by
one, the module will emit 2 tones and the LED will light up (green) for one second every time a multi-access Visiting
card is memorised or the LED will blink rapidly (red) if the card has already been memorised.
-Step 5: Wave the Golmar NFC/IN Installation cards that you wish to add over the proximity reader one by one
(maximum 5 installation cards), the module will emit 2 tones and the LED will light up (green) for one second every
time an Installation card is memorised or the LED will blink rapidly (red) if the card has already been memorised.
-Step 6: To exit “Add access and Installation cards” mode, wave the same Master card usedcards/ key tags / key tag
in Step 1 over the proximity reader again, the LED on the front (red) will turn off.
Not s:e
-The installation card is for advanced configuration and management of the access control (mobile with NFC and
AC Manager app required, Android only), TAC Manager manual (code 50124945).see the
-A maximum of 2,000 cards can be added in steps 2, 3 and 4. The module will emit an error tone and the/ key tags
green LED will light up to warn of when the memory is full.
Remove access (one-access and multi-access) and Installation cards:residents ' cards/ key tags and
-Step 1: Wave a Master card over the proximity reader, the LED on the front will light up (red)./ key tag
-Step 2: Wave the NFC/US Residents' card that you wish to remove over the proximity reader, the LED on the/ key tag
front will blink (red) for a few seconds, the module will emit 2 tones and the LED will light up (green) for one second
confirming that the Residents' card has been removed. Repeat Step 2 if you wish to remove more/ key tag
Residents' cards ./ key tags
-Step 3: Wave the NFC/1U one-access Visiting card that you wish to remove over the proximity reader, the LED on the
front will blink (red) for a few seconds, the module will emit 2 tones and the LED will light up (green) for one second
confirming that the one-access Visiting card has been removed. Repeat Step 3 if you wish to remove more one-
access Visiting cards.
-Step 4: Wave the NFC/MU multi-access Visiting card that you wish to remove over the proximity reader, the LED on
the front will blink (red) for a few seconds, the module will emit 2 tones and the LED will light up (green) for one
second confirming that the multi-access Visiting card has been removed. Repeat Step 4 if you wish to remove more
multi-access Visiting cards.
-Step 5: Wave the NFC/IN Installation card that you wish to remove over the proximity reader, the LED on the front will
blink (red) for a few seconds, the module will emit 2 tones and the LED will light up (green) for one second confirming
that the Installation card has been removed. Repeat Step 5 if you wish to remove more Installation cards.
-Step 6: To exit “Remove access and Installation cards” mode, wave the same Master cardcards/ key tags / key tag
used in Step 1 over the proximity reader again, the LED on the front (red) will turn off.
23
ON DIP
4 51
