Goosky S2 Manuale utente

Flight Control Setting

Binding

with in-built Receiver:

Goosky T8:

Turn on the GOOSKY T8 transmitter,2.4Ghz

press the BIND button 3 times after the helicopter is powered on. The blue

light will flash quickly. Keep the transmitter less than one meter away from the

flight controller. Once the flight control passes self-detection and the blue light

is solid on, the binding is done.

built in Receiver:

Goosky s2 flight control box

built in Receiver

(Spread Spectrum Mode (S-FHSS )

(Frequency 2.4Ghz (2.404GHz--2.4475 )

s-bus

Futaba Tx:

Turn on the Futaba transmitter, adjust the communication protocol to (S-FHSS).

Long press and hold the BIND button as the aircraft is powered on, the blue

light then flashes quickly. Keep the transmitter less than one meter away from

the flight control. Once the flight control passes self-detection and the blue

light is solid on, the binding is done.

Diagram of flight control

SET - Setting menu button

S1 - On/Off Attitude Mode button

LEDs:

SERVO - Servo midpoint settings (swash levelling)

PITCH - Pitch setting (Positive and negative pitch)

SPEED - Speed indicator (Rotation rate)

AGILE - Sensitivity indicator (Feed forward)

GYRO - Sensitivity indicator (Gyro gain)

RUD - Yaw parameter adjustment mode

ELE –Elevator cyclic parameter adjustment mode

AIL –Aileron cyclic parameter adjustment mode

Note1: Bind the remote controller to the aircraft and wait for the flight controller to initialize

before making flight control settings adjustments.

Note2: Parameters can be adjusted manually or via BT adaptor and App on iOS or Android.

To enter the menu, long press and hold SET for 3 seconds →RUD light is solid-on →

SPEED light flashes

Yaw speed setting (rotation rate)

With the RUD light solid-on in white and the SPEED blue light flashing, you are

reading the yaw speed setting. The factory default yaw speed is 5, you will see

the BLUE light flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (faster rotation rate) and back stick to give

a lower setting. The number of consecutive flashes represents the setting level.

The highest setting is 9 and the lowest setting is 1 flash (slowest rotation rate).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

RUD light is solid-on →click SET →GYRO light flashes

Yaw gyro gain setting

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light RUD is solid-on and the GYRO light

flashes. The factory default yaw gain is 5 and you will see the BLUE light

flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (higher gain) and back stick to give a lower

setting. The number of consecutive flashes represents the setting level. The

highest setting is 9 and the lowest setting is 1 flash (lowest gain).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

ELE light is solid-on →click SET →SPEED light flashes

Elevator speed setting (rotation rate)

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light ELE is solid-on and the SPEED light

flashes. The factory default elevator speed is 5 and you will see the BLUE light

flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (faster rotation rate) and back stick to give

a lower setting. The number of consecutive flashes represents the setting level.

The highest setting is 9 and the lowest setting is 1 flash (slowest rotation rate).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

ELE light is solid-on →click SET →AGILE light flashes

Elevator agility setting (feed forward)

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light ELE is solid-on and the AGILITY

light flashes. The factory default elevator agility is 5 and you will see the BLUE

light flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (higher agility) and back stick to give a

lower setting. The number of consecutive flashes represents the setting level.

The highest setting is 9 and the lowest setting is 1 flash (lower agility).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

ELE light is solid-on →click SET →GYRO light flashes

Elevator gain setting

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light ELE is solid-on and the GYRO light

flashes. The factory default elevator gain is 5 and you will see the BLUE light

flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (higher gain) and back stick to give a lower

setting. The number of consecutive flashes represents the setting level. The

highest setting is 9 and the lowest setting is 1 flash (lowest gain).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

AIL light is solid-on →click SET →SPEED light flashes

Aileron speed setting (rotation rate)

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light AIL is solid-on and the SPEED light

flashes. The factory default aileron speed is 5 and you will see the BLUE light

flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (faster rotation rate) and back stick to give

a lower setting. The number of consecutive flashes represents the setting level.

The highest setting is 9 and the lowest setting is 1 flash (slowest rotation rate).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

AIL light is solid on →click SET →AGILE light flashes

Aileron agility setting (feed forward)

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light AIL is solid-on and the AGILITY

light flashes. The factory default aileron agility is 5 and you will see the BLUE

light flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (higher agility) and back stick to give a

lower setting. The number of consecutive flashes represents the setting level.

The highest setting is 9 and the lowest setting is 1 flash (lower agility).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

AIL light is solid-on →click SET →GYRO light flashes

Aileron gain setting

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the indicator light AIL is solid-on and the GYRO light

flashes. The factory default aileron gain is 5 and you will see the BLUE light

flashing 5 times followed by a pause.

You can use the Elevator stick of the transmitter to raise and lower the setting,

forward stick giving a higher setting (higher gain) and back stick to give a lower

setting. The number of consecutive flashes represents the setting level. The

highest setting is 9 and the lowest setting is 1 flash (lowest gain).

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

click SET →SERVO light flashes

Servo center setting

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the SERVO light is solid-on. Use the yaw, elevator

and aileron sticks on the transmitter to set the servo centers. The yaw stick

corresponds to CH1, the elevator stick corresponds to CH2 and aileron stick

corresponds to CH3.

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

Click SET→PITCH light is solid-on

Collective pitch setting

Press and hold the SET button for 3 seconds to enter the tuning mode, short

press the SET button until the SERVO light is solid-on. Confirm throttle hold is

enabled on the transmitter. Move the throttle/collective stick to the middle

position (50%) and zero your pitch gauge. Push the collective stick up to the

maximum pitch setting and use the elevator stick to change the maximum

pitch, move the collective back to the minimum pitch and use the elevator stick

to change the minimum pitch. The factory setting is plus or minus 11.5

degrees.

After completing setting changes, press and hold the SET button for 3 seconds

to exit and save, then the indicator light turns off and you are ready to fly. Or to

move to the next setting, click the SET button.

Restore factory settings

Click SET 10 times

Altri manuali per S2

Altri manuali Goosky Giocattolo

Goosky

Goosky S2 Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente