Gorilla Concrete Tools GP-2 Manuale utente
Product Manual
GP-2: Slim-Line Dual Component Pump
GP-2: Slim-Line Dual Component Pump
GorillaConcreteTools
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 1
Parts Diagram
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 2
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 3
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 4
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 5
Power Switches: Every unit is equipped
with two on/off switches. Ensure both
switches are off prior to connecting to
power.
The Main Power Switch (fig. 1) is
located on the main power line
coming from the power source and
will turn on electronic controls.
The Dispensing Wand Switch (fig. 2
red arrow) is located on the handle of
the dispensing wand and turns on the
motor and speed control.
Speed Control: (fig. 2. yellow arrow)
This unit is programmed for soft
starting to ensure smooth operation
and dispensing of material, which
means it will take several seconds to
achieve maximum speed.
We recommend turning the speed
control knob all the way counter
clockwise to the 0 throttle position prior
to first use.
To increase dispensing rate, turn
speed control knob clockwise.
Pump Control Features:
Familiarize yourself with the pump prior to use
Pump Features
Pump Features
Warnings!
These instructions are only intended to show you the
set-up of our pump. Do not use until you have been
trained on how to properly operate a polyurea pump.
Wear appropriate safety gear when operating this pump
Always use the same tanks with similar chemicals. Mixing
materials will cause curing inside of the tanks, pumps, and
hoses
Store pump properly according to guidelines
GP-2 Features, Set Up, and Cleaning
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 6
Read the manufacturer's safety data
sheet and instructions for the material
you will be using.
Mix components according to the
manufacturer's instructions.
After mixing components, pour Part A
into Part A tank, and then, pour Part B
into Part B tank. (Fig. 1)
Filling Pump:
1.
2.
3.
Never cross contaminant tanks.
Clean off the manifold with the static
mixing tip removed. (Fig. 2)
Dispense material into a waste container
to check for a smooth, air-free flow of
both components. Make sure that there
are two smooth, consistent streams.
If the streams of material are not
consistent, check for blockages and
clean the manifold accordingly and
repeat the previous steps.
Attach a new static mixing tip onto the
manifold.
If dispensing a cure sample, follow long-
term interruptions directions below.
Preparing for Use:
1.
2.
a.
3.
a.
____________________________
Short Term (5 or so minutes): periodically
trigger applicator wand to dispense material
into a waste container every 30-45 seconds to
ensure the material in static mixing tip does not
set.
Long Term (lunch break or cure sample):
remove static mixing tip and discard. Pump
grease into fittings on the manifold. Upon
returning to work, re-install a new static mixing
tip.
Work Interruptions:
1.
2.
Figure 1
Figure 2
____________________________
Figure 2
Pump Set Up
Pump Set Up
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 7
Pump Cleaning
Pump Cleaning
Always clean in a well-ventilated area
Do NOT clean the pump near open flames or
welders
Wear protective gear
Dispose of all waste correct and according to
local guidelines
Warnings
8 cups of manufacturer's recommender
cleaner
4 cups of oil (we recommend vegetable)
Solvent proof gloves and splash-proof goggles
Waste buckets
Rags or Paper towels
Proper storage container for leftover material
Materials Needed:
Dispose of all remaining material by purging it straight through the manifold without a
static mixer attached into a waste container. Follow manufacturer's guidelines for material
disposal.
After emptying, pour 4 cups of cleaner into each tank.
Purge through the system, including the manifold to clean it out.
Repeat steps 2 and 3 as needed until lines are clean.
Verify that all cleaner has been purged from the system.
Wipe tanks clean with the manufacturer's recommended cleaner.
Tank Cleaning:
1.
2.
3.
4.
5.
6.
________________________________________________________
After cleaning, pour at least 2 cups of oil (we recommend vegetable) into each tank.
Purge any remaining cleaner from the system using the oil. Leave some oil in the lines,
manifold, valves, and pumps for proper storage.
Using manifold grease fittings, pump grease into manifold until it comes out of the
dispensing ports.
Proper Storage:
1.
2.
3.
________________________________________________________
Call (+1(440)-236-5112) or visit our website (www.gorillaconcretetools.com) for our terms and conditions
Page 8
Optional GP-2-24 Battery Configuration
Optional GP-2-24 Battery Configuration
2 Batteries Required (not included):
Group 24 Deep Cycle Lead Acid (Flooded Type)
This is a 24-volt circuit. Failure to properly connect terminals will void the product warranty.
Plug in the bottom two terminals using the black jumper cable, with the red plug
attaching to the positive terminal of battery 1 and the black plug attaching to the
negative terminal of battery 2. (yellow arrows)
Plug in the red positive wire to the positive terminal of battery 2. (blue arrow)
Plug in the black positive wire to the negative terminal of battery 1. (green arrow)
Battery Installation:
1.
2.
3.
THIS STEP MUST BE DONE LAST.
Indice
Altri manuali Gorilla Concrete Tools Pompa dell'acqua
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente