Gotharman Gotharman's Tiny LD Manuale tecnico
1
Gotharman’s Tiny LD
Granular Workstation
Update Manual 12.96
2
-Tiny LD only: Now compatible with new dual line SSI2140 filterboard –VCF conn V2 required
Page 4
-Tiny LD only: The LOWR button can now function as a Freeze button Page 11
-Parametric EQ insert effects added Page 12
-All sequencer steps on a subtrack can now be offset adjusted with one knob movement Page 15
-Position Rotation Modulation added to the Sequencer note tracks Page 16
-It is now possible to output one Audio BUS to another Audio BUS. Page 17
-A BUS Follower/Envelope OFF position has been added. Page 18
-Insert effects input gain can now be adjusted Page 19
-When recording an audio track, the BPM of this is now included in the sample name
Page 20
-Audio inputs can now be swapped Page 21
-Quick Edit Knob can now be switched off Page 22
-Some page names on the BUS pages have been changed, to make it look less cryptic. Page 23
A few things, that were missing in the User Manual, has now been added:
-Chop Mode parameter description Page 26
-How to set up (stereo) samplings Page 27
Bug Fixes:
In my eager to make everything run as fast as possible, I unfortunately managed to create a bug, in
an earlier update, which got the audio inputs sample frequency lowered. I sincerely apologize for
this, but now it is back to 44.1 KHz. Thanks a ton to Joakim Gleisner for doing all the necessary
measurements, to detect this.
The 2 Morph knobs would not work in their entire range, when controlled via MIDI. Now they will.
If a part that was set to external, was the selected part, the Morph knobs stopped working. This
has now been fixed.
3
If a knob was set up to modulate the output effects Mix and Pan, the Quick Edit function would
not be switched off. This has now been fixed.
Clear Controller Track were using the track number selected by the Note Tracks. Now it is using
the Controller Track number.
Tiny LD only: When selecting mod sources for parameters, CC4-15 was incorrectly displayed as
CC5-16. This has now been corrected.
Tiny LD only: The green dot and parameter row selection was missing on the WaveBuilder page.
This has now been fixed.
Tiny LD only: When accessing the Random page, and the lower row of parameters were selected,
it would not be possible to adjust the random range. Now it will.
4
SSI2140 Dual Line Filterboard
A new dual line multi-mode filterboard, based on the great new SSI2140 filter chip, are now
compatible with Tiny LD.
Please note that your Tiny LD must have the VCF connector MkII installed, in order for this to
work. All Tiny LD MkII’s, that were ordered with a VCF connector, has this connector installed.
Later MkI’s might also have this installed. Please check on your receipt. The price of the MkII
connector is currently EUR 170, while the MkI connector costed EUR 150. If your Tiny LD has the
MkI VCF connector installed, and you would like to use it with the new dual line filter, it can be
upgraded at Gotharman’s for the price difference.
The Dual SSI2140 filterboard has 2 analog multimode filters. Each of these filters can be assigned
to their own Audio Bus, doubling the Tiny LD analog filter power!
Each of the filters has 4 filter blocks. By combining these blocks, using VCA’s, it is possible to obtain
a number of different filter modes.
It comes with a number of pre-programmed filter types, but it is also possible to adjust these, to
obtain an even wider range of filter types.
If different filter types are selected for morph layer A and B, it will morph between the filter types.
5
After installing the SSI2140 filterboard in your Tiny LD, you must go to MOR>VCF TYPES, to set it
up.
Select VCF number 60-Dual SSI2140.
After you have selected this, turn your Tiny LD off and then on again, to make it set up things right.
6
On the Synth VCF pages, you will now find the Dual SSI2140 parameters.
On the top of the VCF pages, you will find 2 touch buttons, named “1” and “2”. Touch these to
switch between the settings for VCF1 and VCF2.
Since the settings for VCF1 and VCF2 are the same, only the settings for VCF1 will be explained
here.
Cut: 0 to 511. Adjusts the filter cutoff frequency.
Reso: 0 to 511. Adjusts the resonance of the filter.
Inp: 0 to 511. The audio input level for the filter.
Type: Selects a pre-programmed filter type, that can be adjusted using Adj1-4. Different filter
types can be selected for morph layer A and B, to make it morph between the filter types.
The pre-programmed filter types are: LPF4, LPF3, LPF2, LPF1, BPF1, BPF2, BPF3, B3_2, BPF4, B3L1,
B3L2, B4L1, H3L1, HPF3, APF3, A3L1, Not1, Not2, Dst1, Dst2, Dst3, Dst4, Dst5, Dst6, Free (design
your own filter type, by adjusting Adj1-4).
Adj1-4: -128 to +127. Adjusts the level of the filter block 1-4 VCA’s, to obtain different filter types.
7
Touch the RAY touch button, to enter this page.
G-Ray: Adjusts the amount of g-RAY intermodulation. 0: no g-RAY, 3: max g-RAY. Range: 0 to 3.
Mode: G-Ray mode.
-Norm: Normal 1:1 feedback.
-Neg: 1:1 feedback with the signal inverted (a 180 degree phase shift)
-Ultr: Boosted feedback.
-Uneg: Boosted feedback with the signal inverted (a 180 degree phase shift)
Feed: 0 to 511. G-Ray feedback level.
FmBus: 1 to 8. The audio bus, that will apply the audio signal for FM.
Cut3: Has currently no effect on this filter.
Out2: Has currently no effect on this filter.
FM: 0 to 511. The amount of frequency modulation (audio range), that are applied to all of the
filter cutoff frequencies, from the audio Bus selected by the FmBus parameter.
8
Touch the MO1 touch button, to enter this page.
The VU-meter at the right of the screen, shows the filter output activity.
For each parameter, that can be modulated, it is possible to select a modulation source, and to
adjust the modulation amount. Only the positive modulation sources, can be selected by the Edit
Knobs. To make a modulation source negative, touch the modulation source parameter. For a
complete list of modulation sources, see the list in the start of this section.
The upper row of parameters selects the modulation sources, The lower row of parameters
(Labelled Amt) adjusts the modulation amount in the range 0 to 511.
Cut1, Cut2: Will modulate the Cutoff Frequency.
Peak1, Peak2: Has currently no effect on this filter.
9
Touch the MO2 touch button, to enter this page.
The VU-meter at the right of the screen, shows the filter output activity.
For each parameter, that can be modulated, it is possible to select a modulation source, and to
adjust the modulation amount. Only the positive modulation sources, can be selected by the Edit
Knobs. To make a modulation source negative, touch the modulation source parameter. For a
complete list of modulation sources, see the list in the start of this section.
The upper row of parameters selects the modulation sources, The lower row of parameters
(Labelled Amt) adjusts the modulation amount in the range 0 to 511.
Reso: Will modulate the amount of resonance applied to all filters.
Feed: Has currently no effect on this filter.
Out: Has currently no effect on this filter.
Gfeed: Will modulate the amount of G-Ray feedback applied.
10
Touch the Mix touch button, to enter this page.
The VU-meter at the right of the screen, shows the filter output activity.
Bus: 1 to 8. The audio Bus, that the filter will be placed on.
Inp: 0 to 511. The audio input level for the filters.
Outp: -128 to +383. The output level of the filters.
Conn: Ser/Par. (Only on VCF2). Places this filter in either serial or parallel to VCF1, when the filters
are placed on the same Audio Bus.
ModPrt: 1 to 16. The part from which, the filter modulation sources will be added.
Altri manuali Gotharman Strumento musicale
