GOVCOMM GC-IL-Series Manuale utente

External Positioner (Fixed) Camera

Quick Installation Guide

[email protected] | 305-937-2000 | 3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312

GC-IL-Series

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

Thank you for purchasing GovComm’s network ITS Camera product. If there are any technical or

general questions, concerns or requests, please contact us through our website www.GovComm.us, by

email Sales@ GovComm.us or by telephone 1+305-937-2000.

This manual may contain several technical or printing errors, and the content is subject to change

without notice. We regularly improve and update our products and procedures described in the manual.

Updates will be added to new versions of this manual and posted onto the GovComm website.

DISCLAIMER STATEMENT

“Underwriters Laboratories, Inc. (“UL”) has not tested the performance or reliability of the

security or signaling aspects of this product. UL has only tested for re, shock or casualty

hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certication does not cover

the performance or reliability of the security or signaling aspects of this product. UL MAKES NO

REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING

THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED

FUNCTIONS OF THIS PRODUCT.”

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or

property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings are neglected.

Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

Warnings Follow these safeguards to prevent

serious injury or death.

Cautions Follow these precautions to prevent

potential injury or material damage.

• Proper conguration of all passwords and other security settings is the responsibility of the installer

and/or end-user.

• In the use of the product, you must be in strict compliance with the electrical safety regulations of the

region and nation. Please refer to technical specications for detailed information.

• Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source

with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specications

for detailed information.

• Do not connect several devices to one power adapter as adapter overload may cause over-heating

or a re hazard.

Warnings

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

Cautions

• Please make sure that the plug is rmly connected to the power socket. When the product is mounted

on wall or ceiling, the device should be rmly xed.

• If smoke, odor or noise rises from the device, turn off the power at once and unplug the power cable,

and contact the service center.

• Make sure the power supply voltage is correct before using the camera.

• Do not drop the camera or subject it to physical shock.

• Do not touch sensor modules with ngers. If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the

lens cap to protect the sensor from dirt.

• Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur otherwise

(which is not a malfunction), and affect the endurance of sensor at the same time.

• The sensor may be burned out by a laser beam, so when any laser equipment is used, make sure

that the surface of sensor will not be exposed to the laser beam.

• Do not place the camera in extremely hot, cold (the operating temperature shall be -40°F – 175°F,

dusty or damp locations, and do not expose it to high electromagnetic radiation.

• To avoid heat accumulation, good ventilation is required for operating environment.

• Keep the camera away from liquid while in use.

• While in delivery, the camera shall be packed in its original packing, or packing of the same texture.

• If the product does not work properly, please contact us. Never attempt to disassemble the camera

yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or

maintenance.)

Table of Contents

1 Appearance Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Micro SD Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Initializing the Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Ceiling Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Wall Mounting with a Junction Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Wall Mounting with a Gang Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Setting the Network Camera over the LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3.2 Activating the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3.2.1 Activation via Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3.2.2 Activation via SADP Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.3 Modifying the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 Accessing via Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

[email protected] | 305-937-2000 | 3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

1 Appearance Description

1.1 Overview

The overview of the network bullet camera is shown below.

No. Description

1 Photoresistor

2 Lens

3Sun Shield

4 3-axis Bracket

5Network Cable Interface

6Power Cable Interface

7Alarm Cable Interface

8Video Cable Interface

9Audio Out

10 Audio In

11 Reset Button

12 Micro SD Card Slot

13 Serial Port

NOTE:

• The standard power supply is 12V DC or 24V AC, please make sure your power supply matches

with your camera.

• Press RESET about 10s when the camera is powering on or rebooting to restore the default

settings, including the user name, password, IP address, port No., etc.

Figure 1-1 Overview

Table 1-1 Description

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

1.2 Micro SD Card Installation

This series of camera supports micro SD card installation. Please follow the steps below to install the

micro SD card.

1. Loosen the two lock screws at the bottom of the bullet camera, and then remove the slot cover.

1.3 Initializing the Memory Card

Steps:

Check the memory card status by tapping on the Storage Status in the Device Settings interface.

If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to

Normal. You can then start recording any event triggered video in the camera such as motion detection.

2. Insert the SD card into the SD card slot.

3. (Optional) Push the inserted micro SD card inside to remove the micro SD card.

Re-install the card cover and fasten the two screws to complete the installation.

Figure 1-2 Remove Card Cover

Figure 1-3 Insert the Card

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

2 Installation

Before you start:

• Make sure the device in the package is in good condition and all the assembly parts are included.

• The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with

your camera.

• Make sure all the related equipment is power-off during the installation.

• Check the specication of the products for the installation environment.

• Make sure that the wall is strong enough to withstand four times the weight of the camera and the

bracket.

For the camera that supports IR, you are required to pay attention to the following precautions to

prevent IR reection:

• Dust or grease on the dome cover will cause IR reection. Please do not remove the dome cover lm

until the installation is nished. If there is dust or grease on the dome cover, clean the dome cover

with clean soft cloth and isopropyl alcohol.

• Make sure that there is no reective surface too close to the camera lens. The IR light from the

camera may reect back into the lens causing reection.

• The foam ring around the lens must be seated ush against the inner surface of the bubble to isolate

the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the

dome cover are attached seamlessly.

2.1 Ceiling Mounting

Steps:

1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template.

2. Fix the camera to the wall with the supplied screws.

Figure 2-1 Drill Template

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

NOTE: Please insert the expansion screws rst if the camera is mounted to the cement ceiling. And you

can use the self-tapping screws directly if camera is mounted to the wooden ceiling.

3. Adjust the surveillance angle.

»1). Loosen No.1 lock screw to adjust the tilt angle [0 °~100°].

»2). Loosen No.2 lock screw to adjust the pan angle [0°~360°].

»3). Loosen No.3 lock screw to rotate the camera [0°~360°].

»4). Tighten the lock screws.

NOTE: A wrench is supplied to loosen and tighten the screws.

Figure 2-2 Install the Camera

Figure 2-3 Adjust the Surveillance Angle

Figure 2-4 Supplied Wrench

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

4. (Optional) Install the water-proof jacket for network interface.

NOTE: It is recommended to adopt the water-proof jacket (supplied) for the network interface when the

camera is installed outdoor.

»1). If the network cable has been settled down, cut off the plug of the network cable rst.

»2). Route the network cable through the following components in sequence: x nut, water-proof

ring, and the main body of the water-proof jacket, as shown in the gure.

»3). Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing

ability of the components.

»4). Wire the plug and network cables up.

»5). Fix the O-ring to the network interface of the camera, and then connect the network cables.

»6). Wrap the network interface with the main body of the water-proof jacket, and then rotate the

x nut clockwise to assemble it to the main body of the water-proof jacket.

2.2 Wall Mounting with a Junction Box

Steps:

1. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-1).

2. Align the screw holes of the junction box to the drill template, and x the junction box to the wall

with screws.

3. Route the cables.

4. Fix the camera to the junction box with screws.

5. Adjust the surveillance angle according to step 3 in Chapter 2.1.

6. Install the water-proof jacket according to step 4 in Chapter 2.1.

Figure 2-5 Install the Water-proof Jacket

Figure 2-6 Installation with a Junction Box

External Postioner (Fixed) Camera - Quick Start Guide

3830 SW 30 Avenue, Ft. Lauderdale, Florida 33312 | 305-937-2000 | www.GovComm.us | [email protected]

2.3 Wall Mounting with a Gang Box

NOTE: An adapter plate should be purchased separately if you mount the camera to a gang box.

Steps:

1. Install the adapter plate to the gang box.

2. Route the cables.

3. Fix the camera to the adapter plate with screws.

4. Adjust the surveillance angle according to step 3 in Chapter 2.1.

5. Install the water-proof jacket according to step 4 in Chapter 2.1.

Figure 2-7 Installation with a Gang Box

Indice

Altri manuali GOVCOMM Telecamera di sicurezza

GOVCOMM

GOVCOMM GC-IMPO-FIZDE Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente