Grace Company Continuum II Guida rapida alla configurazione
Copyright September 18, 2020
Grace Company
(Reproduction Prohibited)
Version 1.0
Just purchased your frame?
Save time setting it up by following the instructions in this manual!
12 Foot Frame - Assembly & Use
2
Included Parts & Tools....................................................................................3
Extended Frame Assembly..............................................................................4
Step 1 - Setting the Frame Height.........................................................................................................5
Step 2 - Building the Frame Table ........................................................................................................7
Step 3 - Installing the Tracks.............................................................................................................. 12
Step 4 - Assembling the Rail Supports.............................................................................................. 16
Step 5 - Installing the Bottom Carriage ............................................................................................ 17
Step 6 - Installing the Quilting Machine .......................................................................................... 19
Step 7 - Leveling the Frame................................................................................................................ 21
Step 8 - Installing the Rails................................................................................................................. 23
Step 9 - Assembling the Handwheel.................................................................................................. 29
Step 10 - Installing the Bungee Clamps............................................................................................ 30
Step 11 - Adjusting the Rails .............................................................................................................. 31
Step 12 - Installing the Velcro Tape.................................................................................................. 33
Step 13 - Installing Leader Cloth ...................................................................................................... 36
Upgrade Existing Frame................................................................................38
Step 1 - Rail Assembly......................................................................................................................... 39
Step 2 - Track Assembly...................................................................................................................... 42
Step 3 - Extending the Table............................................................................................................... 47
Step 4 - Installing the Tracks.............................................................................................................. 51
Step 5 - Leveling the Frame................................................................................................................ 53
Step 6 - Installing the Rails................................................................................................................. 55
Step 7 - Adjusting the Rails ................................................................................................................ 57
Step 8 - Installing the Velcro Tape.................................................................................................... 59
Step 9 - Installing Leader Cloth ........................................................................................................ 62
Using Your Frame..........................................................................................64
Sizing the Quilt Backing and Batting................................................................................................ 65
Attaching the Fabric ............................................................................................................................ 66
Using the Channel Locks.................................................................................................................... 70
Contents
3
Included Parts & Tools
Please make sure all pieces are included in your kit.
Middle Leg
CII-09-14523
See page 5, 47
Middle Leg
Brace (x2)
CII-04-14504
See page 7, 47
Track Support
Connector (x2)
CNT-04-11041
See page 12, 42
2 ft Table Section
CII-09-14639
See page 7, 42
12 ft Plastic
Track (x4)
CII-05-10561
See page 12, 42
2 ft Rail Sections (x3)
CII-04-11397
See page 23, 39
12 ft Leader
Cloth Set
CII-09-14777
See page 33, 59
Rail Coupler (x3)
CNT-08-11865
See page 23, 39
HDW-03-10951
See page 7, 47
SBHCS Screw
M8 x 16 mm (x16) Set Screw
M6 x 6 mm (x8)
HDW-03-10037
See page 12, 42
4 mm
T-Handle Allen
Wrench 4 mm
14
17
Allen Wrench 5 mm
Allen Wrench 3 mm
HDW-03-13114 HDW-03-10741
HDW-03-10166
4
Extended Frame Assembly
This section describes the steps for setting up the frame if the base frame has not yet been
assembled. For steps on extending a frame that has already been set up, see “Upgrade Existing
Frame” on page 38.
Tip: For additional help, scan the QR code below with the camera on your smart
phone to visit our online support videos!
https://www.graceframe.com/en/resources/support/videos
5
Extended Frame Assembly
Step 1 - Setting the Frame Height
Parts & Tools Needed:
Right Leg
Left Leg Middle Leg (x2)
Open-ended Wrench
10 mm & 13 mm
14
17
14
17
Allen Wrench 5 mm
Instructions
The frame height is most easily adjusted prior to frame assembly. Please take the following steps:
On all legs: Remove the M8 x 55 mm
SBHCS height screws, washer, and nut
with the 10 mm open-end wrench and
5 mm Allen wrench.
Nut (x2)
2
From Base Frame From Base Frame
Height
Screw (x2)
Washer (x2)
Note: Middle legs have only one nut, washer,
and M8 x 55 mm SBHCS height screw.
On all legs: Loosen (do not remove) the
set screws toward the base of each leg
with the 4 mm Allen wrench.
1
Set Screws
Note: Middle legs have only one set screw.
4 mm
T-Handle Allen
Wrench 4 mm
From Base Frame
Extension Box
Extension Box
From Base Frame
& Extension Box
6
On all legs: Raise the top of the leg until
the leg is the desired height. Re-install the
height screws, washer and nut.
3
Important: Set all the legs to the same
height hole.
On all legs: Re-tighten the set screws with
the 4 mm Allen wrench. The middle leg has
only one set screw.
4
Note: Final height may vary slightly after
adjusting the leveling feet (see page 21).
Set Screws
Setting the Frame Height (Continued)
Extended Frame Assembly
7
On all table sections (long and short): Use the 4 mm T-handle Allen wrench to remove the
M6 x 8 mm connector bolts attaching the metal track supports.
1
Step 2 - Building the Frame Table
Parts & Tools Needed:
14
17
Allen Wrench 5 mm
SBHCS Screw
M8 x 16 mm (x40)
Table Section (x2)
Corner Brace (x4)
Middle Leg
Brace (x4)
Extended Frame Assembly
Left Leg
Middle Leg (x2)
4 mm
T-Handle Allen
Wrench 4 mm
From Base Frame
From Base Frame
Instructions
Attach the table tops to the frame legs by taking the following steps:
From Base Frame
& Extension Box
M6 x 8 mm
Connector Bolt
Track
supports
Table Section 2ft
Extension Box
From Base Frame
& Extension Box
8
3
Building the Frame Table (Continued)
Extended Frame Assembly
2
Attach one of the corner braces to the top left corner of the frame with the 5 mm Allen
wrench and four M8 x 16 mm SBHCS screws.
4
Use two M8 x 16 mm SBHCS screws and the 5 mm Allen wrench to attach the left table
section to one of the the middle legs.
M8 x 16 mm
SBHCS (x2)
Use two M8 x 16 mm SBHCS screws to attach the left frame leg to the underside of one of
the long table sections. Tighten with the 5 mm Allen wrench.
M8 x 16 mm
SBHCS (x2)
Left Frame Leg Long Table
Section
Middle Leg
M8 x 16 mm
SBHCS (x4)
Corner Brace
Note: Keep table and leg as square as possible while attaching brace.
9
Use two M8 x 16 mm SBHCS screws to attach the right frame leg to the underside of the
remaining table section. Tighten with the 5 mm Allen wrench.
M8 x 16 mm
SBHCS (x2)
Table Section
Right Frame
Leg
Carefully lift the table to a standing position.
5
6
Building the Frame Table (Continued) Extended Frame Assembly
7Use two M8 x 16 mm SBHCS screws and the 5 mm Allen wrench to attach the right table
section to the free middle leg.
M8 x 16 mm
SBHCS (x2)
10
7Attach one of the corner braces to the top right corner of the frame with the 5 mm Allen
wrench and four M8 x 16 mm SBHCS screws.
M8 x 16 mm
SBHCS (x4)
Corner Brace
Note: Keep table and leg as square as possible while attaching brace.
8Line up the two table sections so there is about 2 feet of space between them.
8Carefully lift the second half of the frame into a standing position.
2 Feet
Building the Frame Table (Continued)
Extended Frame Assembly
Altri manuali per Continuum II
1
Indice
Altri manuali Grace Company Accessori per macchine da cucire
