Graco ST Max 395 Hopper Manuale
www.graco.be
ST Max™395
ST Max™II 495/595
SETUP
Connect hose to sprayer and gun.
Tighten hose connections with wrench. Unscrew tip & guard from gun.
Fill throat packing nut with TSL™
to prevent premature packing wear.
Make sure power
switch is set to OFF.
Plug electrical cord
into grounded outlet.
Turn prime valve
to Prime position (down).
Place siphon tube in pail
partially filled with water.
Turn pressure control knob
to lowest pressure, and set
power switch to ON.
Increase pressure until
sprayer starts and water
runs out of prime tube.
Let water run out of prime
tube for 15 seconds.
Decrease pressure
until sprayer stops.
Turn prime valve
to Spray position
(horizontal).
Make sure safety
lever of gun is OFF.
Aim gun at inside
wall of water pail
and squeeze trigger.
Increase pressure until
sprayer starts. Keep gun
triggered into water pail for
1 minute. Release trigger.
Turn prime
valve to Prime
position (down).
Place siphon tube in paint
pail, but leave drain tube
in water pail.
Aim gun at inside
wall of water pail,
and squeeze trigger.
Transfer drain
tube to paint pail.
Increase pressure until
sprayer starts and paint
comes out of drain tube.
Keeping gun triggered into water
pail, turn prime valve
to Spray position (horizontal).
When paint comes out of gun,
release trigger and turn safety
lever of gun to ON.
Screw tip & guard onto gun, making sure
arrow-shaped handle of tip is pointing forward.
You can reverse this tip to quickly clear clogs
without taking it apart.
This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing
fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.
* check the Graco operations manual delivered with the unit for more details.
CHOOSE THE RIGHT TIP & FILTER
WARNING
Quick Operator’s Guide
207
307
109
209
309
409
509
609
111
211
311
411
511
611
113
213
313
413
513
613
115
215
315
415
515
615
815
217
317
417
517
617
817
917
119
219
319
419
519
619
819
121
221
321
421
521
621
721
821
223
323
423
523
623
723
225
325
425
525
625
725
327
427
527
627
827
429
529
629
729
331
531
631
831
433
533
633
833
235
435
535
635
735
835
935
439 443
543
645
451
551
455
555
655
5 cm
10 cm
15 cm
20 cm
25 cm
30 cm
35 cm
40 cm
45 cm
3 cm
7 cm
10 cm
15 cm
20 cm
25 cm
30 cm
35 cm
40 cm
pump filter
gun filter
200 mesh
100 mesh
100 mesh
100 mesh
60 mesh
60 mesh
none
none
30 mesh
* at 30 cm spraying distance
Ink
Stains
Lacquers
Enamels
Urethanes
Acrylics
Emulsions
Latex
Block filler
Intumescents
Texture material
for spray applications 1st digit X5
=fan width*
Time to
change!
NEW WORN
SPRAYING
Turn safety lever
of gun to OFF.
Point gun at area to be sprayed about 30 cm from surface, and begin moving gun before triggering. A good spray pattern is evenly
distributed as it hits surface. Set pressure just high enough to spray without heavy edges. Use smaller tip size for thinner material
and a larger tip size for thicker material if pressure adjustment cannot achieve even spray pattern.
SHUTDOWN AND CLEANUP
Set power
switch to OFF.
Trigger gun
until pressure
is relieved.
Turn prime valve
to Prime position (down).
Remove gun
filter assembly.
Unscrew tip & guard from
gun. Clean gun filter, inlet
screen, tip, guard and
manifold filter with water
and brush.
Set power switch to ON,
and increase pressure
until sprayer starts.
As soon as Pump Armor
comes out of drain tube,
set power switch to OFF.
Screw inlet screen onto
siphon tube, replace
manifold filter and spacer,
and assemble gun with
filter, tip and guard.
Wipe outside of sprayer,
hose and gun with rag
soaked in water or
mineral spirits.
Fill throat packing
nut with TSL.™
Place drain tube
and siphon tube
in pail of water.
Turn pressure control knob to
lowest setting, set power switch
to ON, and increase pressure until
sprayer starts. Let sprayer run and
flush itself for 2 minutes.
Keeping gun triggered
into water pail, turn prime
valve to Spray position
(horizontal).
Set power switch to OFF, turn
pressure control knob to lowest
setting, and turn prime valve to
Prime position (down).
Place drain tube in waste
pail and siphon tube in
container of Pump Armor™
Assemble gun
without filter.
Unscrew inlet screen
from siphon tube.
WASTE
Keep gun triggered
into pail for 1 minute,
until water coming out
of gun is clean.
Remove manifold
filter and spacer.
t
GRACO N.V. Industrieterrein Oude Bunders
Slakweidestraat 31 • B-3630 Maasmechelen
Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777
All information, illustrations, and specifications in this document are based on the latest product information
available at the time of publication. The right is reserved to make changes at any time without notice.
© 2002, 2006 Graco N.V. · Form No. 328007 E (rev.C) · 01/08 · Printed in Europe.
Graco is certified ISO 9001.
Altri manuali per ST Max 395 Hopper
1
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Graco Spruzzatore di vernice
Graco
Graco Optimiser 2K Manuale operativo
Graco
Graco 237-418 Manuale operativo
Graco
Graco QuickShot Manuale utente
Graco
Graco ToughTek S340e Manuale per l'uso e la cura
Graco
Graco FinishPro II 295 Manuale per l'uso e la cura
Graco
Graco ULTRA MARK X Manuale
Graco
Graco TrueCoat 360 Project Series Manuale utente
Graco
Graco Contractor 288477 Manuale operativo
Graco
Graco TX 90 Istruzioni operative
Graco
Graco 223963 Manuale utente
Graco
Graco RTX 1500 Manuale utente
Graco
Graco SG2 Manuale utente
Graco
Graco HYDRA-SPRAY EH 333 226-333 Manuale operativo
Graco
Graco REACTOR 246033 Manuale utente
Graco
Graco HVLP TurboForce II 7.0 Manuale
Graco
Graco AirPro 313869B Manuale utente
Graco
Graco 234237 Manuale utente
Graco
Graco 248037 Istruzioni per il montaggio
Graco
Graco Finex 289256 Manuale operativo
Graco
Graco Magnum Pro Plus Guida
