Graco T-MAX 506 Manuale

T-MAX™506/657

www.graco.com

STARTUP

STARTUP Spray with Air <= 1.5 mm

Fill material hopper

with pre-mixed texture

material.

Turn pressure control

knop until a steady

stream flows from

material hose. Turn pump OFF.

Turn applicator OFF,

Turn ON/OFF switch

to ON

Lossen nut on bottom

of pump

two to three turns to

relieve pressure

Turn pressure control

to maximum. To spray,

aim applicator with a

distance of 0,5 m to the

wall and open applictor.

To clean a tip clog, turn

applicator OFF, turn Tip 180°

to Clean position, aim in waste

area, turn applicator ON, when

clog clears, turn applictor OFF

and tip in spray postion.

Turn pressure

control off (0).

Point applicator

into hopper.

Turn applicator ON.

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure Relief

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure

Relief

Use different tip size

for different flow

Install filter and tip

extension.

Connect applicator

to material hose.

Add water if thinning is

required. Mix thoroughly.

HDA531

HDA535

HDA541

HDA545

HDA651

HDA661

HDA671

mc03 m

Spray without Air < .25 mm

Srew tip assembley

onto applicator

Fill material hopper with

mixed texture material.

Place material hose in Hopper turn ON/OFF switch to ON Turn

control in the “green” segment, allow material to circulate 30 sec.

Turn pump control to

shut pump off

Screw air hose and valve to applicator.

Connect material hose to gun kit

Turn applicator valve OFF.

Install air nozzle.

Hold applicator over

material hopper and turn

applicator ON.

Turn air compressor ON. Turn pump

control in the “green” area, until

desired material rate is achieved.

Regulate the air valve to

get a good atomization.

To stop spraying,

turn applicator OFF

Quick Operator’s Guide

SETUP

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

WARNING

Turn pump control off (0).

Connect power cord.Connect pump module to hopper cart.

Remove pump plug.

Connect material hose to pump outlet.

PRESSURE RELIEF PROCESS

Turn pump control counter clockwise,

to shut pump off.

Close applictor after pressure release,

close air valve

Scrape material remaining in

hopper into pump to be pumped

from sprayer.

Rotate pump control to

(0) to shut pump off.

Shut OFF air compressor if spraying with air.

Remove applicator from material hose.

Clean applicator.

Rotate pump control

clockwise to start pump.

Rotate pump control to (0) to

shut pump off.

Clean applicator, spray tips and

guard with brush.ON/OFF switch to OFF

Turn pump control

clockwise and pump

unused texture material

from material hopper

and hose.

Run pump until

cleaning ball exits

material hose.Save

cleaning ball. Repeat

it till the water that

comes out is clear.

Insert wet cleaning ball into pump.

Connect material hose to pump outlet.

Clean hardened material

from applicator nozzles

with air nozzle cleaner.

Remove drain plug from Hopper

Clean hopper with water, brush

and sponge, install drain plug. fill

hopper 1/3 with clear water.

GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

www.graco.com

Graco is certified ISO 9001.

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

CHOOSE THE RIGHT TIP (HDA-XXX)

CLEANUP

XTRA LIGHT LIGHT MEDIUM HEAVY

HDA531 HDA541 HDA651 HDA671

HDA535 HDA545 HDA661 -

VERY FINE - 3MM FINE - 4MM MEDIUM - 6MM MEDIUM HEAVY - 8MM HEAVY - 10MM

248888 248524 248525 248526 248527

Altri manuali per T-MAX 506

Questo manuale è adatto per i seguenti modelli

Altri manuali Graco Spruzzatore di vernice

Graco

Graco EH 333 HYDRA-SPRAY A Series Manuale operativo

Graco

Graco 25T804 Manuale utente

Graco

Graco 18H269 Manuale utente

Graco

Graco Reactor 3 E-XP1 Standard Manuale di istruzioni

Graco

Graco Pro/Delta Spray 240367 Manuale operativo

Graco

Graco Reactor A-25 Manuale di istruzioni

Graco

Graco IronMan 256790 Guida

Graco

Graco 238338 Manuale operativo

Graco

Graco Magnum Pro Plus Series Guida

Graco

Graco XP Guida

Graco

Graco FieldLazer 248942 Manuale utente

Graco

Graco RTX 1500 Manuale di istruzioni

Graco

Graco Optimiser 02017 Manuale utente

Graco

Graco 238-258 Manuale operativo

Graco

Graco 231-353 Manuale operativo

Graco

Graco magnum pro plus a45 Manuale utente

Graco

Graco field lazer s100 Manuale utente

Graco

Graco 16N657 Manuale di istruzioni

Graco

Graco Alpha Plus AA Manuale operativo

Graco

Graco 455st Pro Manuale di istruzioni

Graco

Graco Reactor 2 H-30 Manuale di istruzioni

Graco

Graco 308640 Manuale operativo

Graco

Graco 245095 Istruzioni per il montaggio

Graco

Graco Pro Xp 3A2494D Manuale utente

Manuali Spruzzatore di vernice popolari di altre marche

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuale utente

Binks

Binks SV100 Manuale utente

Fimco

Fimco LG-4-3-1 Manuale utente

AG SPRAY

AG SPRAY FS-ATV-25BL Manuale utente

Nordson

Nordson MicroMax 2 Manuale utente

Bonide

Bonide 051 Manuale operativo

zogics

zogics Z-DAS Manuale utente

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuale utente

Matrix

Matrix SG 650 Manuale utente

Anest Iwata

Anest Iwata SGA-3 Guida rapida

paasche

paasche VV Scheda tecnica

Carlisle

Carlisle DeVilbiss JGA-510 Manuale utente

Gardena

Gardena 11120 Manuale utente

Conrad

Conrad Hobby Airbrush K3 Manuale utente

wiwa

wiwa 14025 R/F Manuale utente

DeVilbiss

DeVilbiss LUNA2i Manuale utente

WAGNER

WAGNER W 125 Manuale utente

My Clean Buddy

My Clean Buddy PW018 Manuale utente