Graco Manzel MVB 563565 Manuale utente

3A2334A

Instructions

MVB Pump

Provides a predetermined, proportional amount of lubricant to lubrication points. For use

with Graco MVB gearboxes. For professional use only.

Model 563565

1/4 inch diameter piston

8000 psi (552 bar, 55.2 MPa) Maximum Working

Pressure

Model 563566

3/8 inch diameter piston

3000 psi (207 bar, 20.7 MPa) Maximum Working

Pressure

Important Safety Instructions

Read all warnings and instructions in this

manual and in the related system component

manuals before using the equipment. Save all

instructions.

Warnings

23A2334A

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this

manual where applicable.

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical

treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Warnings

3A2334A 3

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See

Technical Specifications in all equipment manuals. Read fluid and solvent manufacturer’s

warnings. For complete information about your material, request Safety Data Sheet (SDS) from

distributor or retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not

limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Installation

43A2334A

Installation

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever

you see this symbol.

1. Disconnect power source.

2. Loosen outlet fitting or alternate outlet until no more

lubricant or air leaks from the fitting. (FIG. 1)

Pump Adjustment

The pump output is adjustable using the 1-1/2 inch

(28.58 mm) hex nut (a) on the top of the pump. Adjusting

the hex nut changes the inlet port position in relation to

the piston top, which regulates g the discharge

volume.

To adjust the pump output:

1. Follow Pressure Relief Procedure, page 4.

2. Loosen screw (8k) (FIG. 2).

3. Turn hex nut (a) (FIG. 2):

• Clockwise to increase output

• Counterclockwise to decrease output

NOTE: Do NOT exceed 0.484 inch (12.24 mm) to pre-

vent insufficient thread engagement of the cylinder and

piston assembly.

4. When the desired output volume is attained,

re-tighten the screw (8k), and torque the screw (8k)

to 20 in/lbs.

5. Re tighten the outlet fitting or the alternate outlet

plug.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop dispensing and before

cleaning, checking, or servicing the equipment.

FIG. 1

Lube Outlet

Alternate

Outlet

(Plugged) or

Gauge Port

FIG. 2

0.484 in. (12.24 mm) MIN OUTPUT

0.250 in. (6.35 mm) MAX OUTPUT

Installation

3A2334A 5

Table 1 provides output changes in relation to the

number of turns the hex nut is adjusted.

Note that full stroke is when the hex nut is flush with body.

Table 1: Output Adjustments

Stroke 1/4 in. (6.35 mm) Diameter Piston 3/8 in. (9.53 mm) Diameter Piston

cubic inch cubic cm cubic inch cubic cm

Full stroke* 0.012 0.197 0.030 0.492

1/4 0.011 0.187 0.028 0.466

1/2 0.011 0.175 0.027 0.439

3/4 0.010 0.164 0.025 0.413

1 0.010 0.156 0.024 0.387

1-1/4 0.009 0.146 0.022 0.361

1-1/2 0.008 0.134 0.020 0.334

1-3/4 0.008 0.124 0.019 0.308

2 0.007 0.115 0.017 0.282

2-1/4 0.006 0.103 0.016 0.256

2-1/2 0.006 0.093 0.014 0.230

2-3/4 0.005 0.084 0.012 0.203

3 0.004 0.072 0.011 0.177

3-1/4 0.004 0.062 0.009 0.151

3-1/2 0.003 0.051 0.008 0.125

3-3/4 0.003 0.041 0.006 0.098

*hex nut turns counterclockwise from full stroke

Disassembly Procedure

63A2334A

Disassembly Procedure

All reference numbers in parenthesis refer to FIG. 3 on

page 8.

1. Disconnect the power source.

2. Follow Pressure Relief Procedure, page 4.

3. Place the pump upside down in a vise with the

pump body in a soft-jaw vise for protection.

4. Depress the piston guide (6) and remove the

self-locking ring (8e) and piston guide (6).

5. Withdraw the piston assembly and piston return

spring (4).

6. With the bottom of the piston visible remove the

retainer ring (8c or 8f), retainer spring (1), and pis-

ton return spring (4).

7. Remove the pump from the vise and turn over. Put

the pump in soft-jaw vise with the adjustment nut

facing upward.

8. Loosen set screw (8k) to relieve locking force on the

piston valves (5). Removal is not necessary.

9. Remove pipe plug (8h or 8j). Unthread and remove

the piston valve (5), being careful not to cut the

o-rings.

10. Replace o-ring and backup rings, if damaged or

worn.

11. Remove the pump from the vise.

12. Place the piston valve (5) in the vise and remove the

indicator port adapter (9).

13. Remove the piston valve (5) from the vise and

remove the ball (8a) and spring (3).

Assembly Procedure

3A2334A 7

Assembly Procedure

1. Place the piston valve (5) in a soft jaw vise and

return the ball (8a) and spring (3). Thread in indica-

tor port adapter (9) and torque to 12 ft-lbs (16 N•m).

2. Remove the piston valve (5) from vise.

3. Place the pump body (10) in a soft jaw vise with

flange end facing down.

4. Thread in piston valve (5), being careful not to cut

the o-rings.

5. Apply a small amount of pipe sealant to pipe plug

(8h or 8j) and, while holding indicator port adapter

(9) with a wrench, tighten the pipe plug (8h).

6. Remove pump body (10) from the vise and turn so

that the flange end faces up.

7. Replace piston return spring (4).

8. Assemble the retainer ring (8c or 8f) and retainer

spring (1) on the piston.

9. Lightly oil piston and insert into piston valve (5).

10. Insert the piston guide (6) and depress slightly to

allow the self-locking ring (8e) to be installed.

Parts

83A2334A

Parts

California Proposition 65

FIG. 3

Ref Part Description Qty

1†556495 RETAINER, spring (model 563565) 1

† 556496 RETAINER, spring (model 563566) 1

2† 556726 GASKET, pump (not shown) 1

3† 556960 SPRING, piston 1

4† 557012 SPRING, return piston 1

5563115 VALVE, piston, 1/4 cylinder (model

563565)

563119 VALVE, piston, 3/8 cylinder (model

563566)

6 560469 GUIDE, piston 1

7† 558015 KIT, MVB pump seal 1

7a 556338 BALL, 0.188 diameter (not shown) 1

7b 556558 O-RING, backup, -015 flurocarbon 1

7c 555683 O-RING, backup, -017 flurocarbon 1

7d C38312 O-RING, -019 flurocarabon 1

7e 555687 O-RING, -012 flurocarbon 1

7f 126066 RING, backup, -19, PTFE 2

7g 126067 RING, backup, -17, PTFE 2

7h 556588 RING, backup, -015 PTFE 2

8† 558016 KIT, MVB Pump Hardware 1

8a 124923 BALL, chrome, .500 1

8b 123977 TAG, direction (not shown) 1

8c 124925 RING, retainer, -25 E-ring 1

8e 558666 RING, retainer, 1-1/2”

8f 126751 RING, retainer, 3/8” 1

8g 100133 WASHER, lock, 3/8” (not shown) 2

8h 557349 PLUG, pipe, 1/8” nptf model

563565

8j 557391 PLUG, pipe, 1/4” nptf model

563566

8k 131775 SCREW, HHCS 1/4 x 0.37 1

8l 558674 SCREW, SHCS, 3/16 x 1.00 (not

shown)

9 560458 Indicator Port Adapter 1

10 560472 BODY, pump, MVB 1

11 260085 SCREW, drive, #2 x 0.125 (not

shown)

Parts are included in Piston Kit 1/4 MVB Pump:

563918

Parts are included in Piston Kit 3/8 MVB Pump:

563919

† Parts are included in Seal Kit 563920.

WARNING: This product can expose you to chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm. For more information, go to

www.P65warnings.ca.gov.

Technical Specifications

3A2334A 9

Technical Specifications

Pump Output in Pints (Liters) per day

MVB Pump

US Metric

Model 563565, 1/4 in. (6.35 mm) Piston

Maximum Output per Stroke 0.012 cubic inches 0.917 cubic cm

Minimum Output per Stroke 0.0025 cubic inches 0.041 cubic cm

Pressure Rating with Single-lobe Cam 8000 psi 552 bar, 55.2 MPa

Pressure Rating with Double-lobe Cam 5000 psi 345 bar, 34.5 MPa

Pressure Rating with Triple-lobe Cam 4000 psi 276 bar, 27.6 MPa

Model 563566, 3/8 in. (9.53 mm) Piston

Maximum Output per Stroke 0.030 cubic inches 0.492 cubic cm

Minimum Output per Stroke 0.006 cubic inches 0.098 cubic cm

Pressure Rating with Single-lobe Cam 3000 psi 207 bar, 20.7 MPa

Pressure Rating with Double-lobe Cam 2000 psi 138 bar, 13.8 MPa

Pressure Rating with Triple-lobe Cam 1500 psi 103 bar, 10.3 MPa

Both Models 563565 and 563566

Outlet Port 1/4 - 18 NPSF

Inlet Port 3/8 - 18 NPSF

Minimum Strokes Per Minute* 5

Maximum Strokes Per Minute* 250

* Make sure that, taking into account selection of gear ratio and choice of cam, the actual number of pump strokes is between 5

and 250.

Single Camshaft

rpm

(Pump Strokes/Min)

Model 563565, 1/4 in. (6.35 mm) Piston Model 56366, 3/4 in. (9.53 mm) Piston

Minimum Output

Adjustment

Maximum Output

Adjustment

Minimum Output

Adjustment

Maximum Output

Adjustment

0.12456 (Constant*) 0.59832 0.29909 (Constant*) 1.4902

Pints Liters Pints Liters Pints Liters Pints Liters

20 2.49 1.18 11.97 5.66 5.98 2.83 29.92 14.15

30 3.74 1.77 17.95 8.49 8.97 4.24 44.88 21.23

40 4.98 2.36 23.93 11.32 11.96 5.66 59.84 28.30

50 6.23 2.95 29.92 14.15 14.95 7.07 74.80 35.38

60 7.47 3.53 35.90 16.98 17.95 8.49 89.76 42.46

70 8.72 4.12 41.88 19.81 20.94 9.90 104.72 49.53

* Constant X strokes per minute = Output in pints per day. For 2 or 3 lobe cams, multiply camshaft RPM X 2 or 3.

Technical Specifications

10 3A2334A

Dimensions

Ref Inch mm Ref Inch mm

A 1.188 30.18 K 5.875 149.23

B 3.544 90.02 L 0.5 12.7

C 1.77 44.98 M 4.0 101.60

D 4.375 111.13 N 2.75 69.85

E 2.188 55.58 P 1.125 28.58

F 2.375 60.33 Q 4.281 108.74

G 2.00 50.8 R 2.875 73.03

H 0.625 15.88 S 6.375 161.93

J 0.250 6.35 T 5.50 139.7

Ref Description

AA 1/4-18 NPSF

BB 0.484 - 0.250 in. (12.29 - 6.35 mm) Max Output

CC Mounting Surface

DD 3/8-18 NPSF Lube Inlet

EE 1/4-8 NPSF Lube Outlet

FF 1/4-18 NPSF Return to Crankcase

GG Filter Primer Option

HH Pressure Indicator

JJ System Fill Option

KK 1/4 NPSF Inlet (Near) 1/4 NPSF Drain (Far)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Graco Pompa dell'acqua

Graco

Graco 3A1339 Manuale utente

Graco

Graco Husky 1050 Series Manuale di istruzioni

Graco

Graco C Series Manuale utente

Graco

Graco E-Flo DC Series Manuale utente

Graco

Graco Check-Mate L100CM Manuale elenco delle parti

Graco

Graco SaniForce FW1111 Manuale utente

Graco

Graco President 218747 Manuale operativo

Graco

Graco 258906 Istruzioni per il montaggio

Graco

Graco G3 Series Manuale utente

Graco

Graco E-Flo Manuale utente

Graco

Graco ToughTek MP-Series Manuale utente

Graco

Graco Wolverine A261 Series Manuale operativo

Graco

Graco Hydra-Clean 1040 Manuale elenco delle parti

Graco

Graco Husky 1040 Manuale operativo

Graco

Graco Check-Mate 450 Manuale utente

Graco

Graco GlasCraft Guardian A Series Manuale per l'uso e la cura

Graco

Graco 232-105 Manuale operativo

Graco

Graco EcoQuip 2 EQm Manuale utente

Graco

Graco ChemSafe 205 Manuale elenco delle parti

Graco

Graco ChemSafe 1590 Manuale operativo

Graco

Graco 224-630 A Series Manuale operativo

Graco

Graco 970185 Manuale operativo

Graco

Graco Series B Manuale operativo

Graco

Graco Husky 3300e Manuale di istruzioni

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente

STA-RITE

STA-RITE ST33APP Manuale utente