GRAPHTEC CE6000-120AP Guida utente

4&561."/6"-

MANUAL NO.CE60AP-UM-8M2

$&"1

$655*/(1-055&3

Preface

Thank you for choosing this product. Carefully keep this manual in a handy location for quick reference as necessity

prior to use to ensure safe and correct use and also to thoroughly understand the functions and operate them

effectively.

Prior to use

Be sure to read the attached "TO ENSURE SAFE AND CORRECT USE" prior to use. Otherwise, it may cause an

unexpected accident or re.

Notes on this Manual

(1) No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,

without the prior written permission of Graphtec Corporation.

(2) The product specications and other information in this manual are subject to change without notice.

(3)While every effort has been made to provide complete and accurate information, please contact your sales

representative or nearest Graphtec vendor if you nd any unclear or erroneous information or wish to make other

comments or suggestions.

(4) Notwithstanding the stipulations in the preceding paragraph, Graphtec Corporation assumes no liability for damages

resulting from either the use of the information contained herein or the use of the product.

Registered Trademarks

All names of companies, brands, logotypes, and products appearing in this manual are the trademarks or registered

trademarks of their respective companies.

This User's Manual is copyrighted by Graphtec Corporation.

Roles of each manual

•Setup Manual (this manual).......Read it to understand Displaying method for CE6000-120AP User's Manual, Method for

connecting this Cutting Plotter with the PC, Installing method for driver software, and to

prepare for the operation.

•User's Manual (PDF data) .........Read it to thoroughly understand the functions of CE6000-120AP.

* P.000 describes the reference pages of User's Manual.

* P.00 indicates the reference page in this Setup Manual.

621609912

Before starting the Setup

Make the following preparations before starting Setup.

•Check that all of the items included in the package. (Please see P.1-2 in the CE6000-120AP User's Manual (PDF).)

For the Parts Names, please see P.1-3 in the CE6000-120AP User's Manual (PDF).

•Assemble the CE6000-120AP, and set up it. For the assembling procedures, see either Manual attached to the Stand or

CE6000-120AP User's Manual (PDF). P.1-5

•When there are virus detection program or system resident program, terminate them beforehand.

•Upon installation, be sure to log on Windows using an account with administrator privileges on your computer.

Flow of setup

Setting up the Plotter main unit

1. Attaching a Tool The cutter blade can replaced depending on the material or thickness of the

media. P.03

2. Loading Media (Paper)

Fix the media to the Plotter. P.05

3. Aligning the Push Rollers Adjust the position of the push roller. P.09

4. About the Initial Setup screen Select "Display Language" and "Length Unit". P.10

5. Set the media type into the Plotter Set the media type to the Cutting Plotter, depending on the set media. P.11

6 Tool adjustment and test cutting

Adjust the protruded cutter edge length and the cutting force depending on the material

and thickness of the media. Make test cutting for the set media to adjust the best condition.

P.11

P.16

Launching the Start menu For each software of CE6000-120AP install them using the Installer housed in

the attached CD-ROM. P.14

Installing the Software

A. Install CE6000-120AP Software

Installing the CE6000-120AP Driver

(Graphtec Plotter Driver)

The CE6000-120AP Driver controls the Plotter and makes plotting according

to the data created by the PC. P.15

• Connecting the USB cable

Turn on the power source of Plotter in the middle of installing, and connect the USB cable.

• Connect the RS-232C Connect the RS-232C cable after installing is nished. P.15

B. Install the User's Manual Installs the CE6000-120AP User's Manual. P.17

The procedures vary depending on the Interface.

1. Attaching a Tool

Attach a tool (cutter plunger, plotter pen) to the plotter.

Attaching a Tool

When mounting the tool in the tool holder, please note the following.

• Push the tool all the way into the holder until its ange contacts the upper part of the holder and then tighten the screw

rmly.

• To prevent injury, avoid absolutely touching the tool immediately after the cutting plotter is turned on or whenever the tool

is moving.

For details, see “Attaching a Tool” on P.2-4 in CE6000-120AP User’s Manual.

The cutter holder is suitable only for use with the cutter plunger. Please refrain from attaching the plotting pen to it.

CAUTION

When pushing the tool holder with your ngers, the blade tip may be protruding. Take care not to cut your ngers.

Supplement

Please make certain to set the cutter plunger of the cutter holder (forward).

1Loosen the tool holder screw.

Tool holder

Bracket to hold tool

Tool holder

Top

Supplement

Set the tool in the cutter holder (forward).

2 While pushing up the tool holder, push until its ange completely touches

the upper part of the holder.

FlangeBracket to hold tool

This cutter holder is

not set backward.

Cutter holder

(Forward)

Flange

Setting up the Plotter main unit

3 Make sure that the tool bracket is engaged on the tool's ange, and then tighten the screw.

Flange

Bracket to hold tool

Removing the tool

When removing the tool, turn it counterclockwise to remove the tool.

Attaching a pen

Attach a pen to the pen station.

• Please make sure to attach the pen to the pen station when setting up a pen.

• To prevent injury, avoid touching the pen immediately after the cutting plotter is turned on or whenever the pen is moving.

1 You can attach the pen by opening up the holder on the pen station with your nger.

Holder

Supplement

Make sure to check that the top part of any

tools mounted on the pen station is set in the

grooves above the pen.

2. Once the pen is attached, releasing the holder xes the pen in place.

Always t into grooves on the pen.

Removing a pen

You can remove the pen by lifting up the holder.

2. Loading Media (Paper)

Both roll media and sheet media can be used with the CE6000-120AP. (For more information about loading a sheet media, please see the

User's Manual (PDF). Load the media according to the instructions given for each type. Use the grit roller on the right side of the media (looking

from the front) as a guide when setting it in the media sensor. Afterwards, adjust the push roller so that it's lined up with the side of the media.

For details, see CE6000-120AP User's Manual (PDF).

CAUTION

Notes when using roll media

•Make sure to reduce the maximum feed rate if there is any trouble with paper feed not using the basket.

•Take all cut/plotted paper out of the basket; paper left in the basket may cause deviations and affect performance for

subsequent jobs.

Loading Roll Media

Supplement

The following gure shows the direction of the

roll media when loading it.

1Set the media ange and paper to the stock shaft and insert in the direction of

the paper.

Stock shaft

Flange screw

Media ange

Determine the desired position, and then tighten the ange screw.

Set the position measurement for the media ange as per the following guidelines

in when using paper with a width of 1200 mm.

If using paper of a different width loosens the ange screw, adjust the position of

the grit roller, then re-tighten the ange screw.

Groove

Flange

screw

Media ange

Media

Approx. 100mm

Grooved portion of the

components should be set so

that the grooves contact the

receiving end of the roller.

Stock shaft

2 Lowering the lever releases the stopper lock.

Lever

3Set the stock shaft in from the front.

CAUTION

•

During a plotting or cutting operation, be

sure to keep your hands, hair, and so forth

away from the media stocker, gears and

rollers.

•

When you are installing media, be careful for

gear, a roller, etc. not pinch you nger.

•Deviations and errors may result if the stock

shaft is misaligned when plotting begins.

Align the receiving end of the media shaft with the grooves on the roller and push

down rmly to set it in place.

Stock shaft

Lever

Roller

Groove

Please make sure to set in the direction of the paper.

4 The left and right media anges feed in the paper roll media. Please tighten the

ange screw and fasten the paper roll into the desired position.

5Lower the media set lever to raise the push rollers.

Push roller

Media set lever

Supplement

•The media must always be positioned over

the media sensor.

•See "Aligning the Push Rollers" P.09

about the position of the push rollers.

6 Put the roll media on the roll media tray and then push the tip of the roll media

forward from the back of the machine. Make sure to pull it so that there is no

slackening across the roll media's route.

Media guide

Media sensor

The paper roll media’s route goes over the center bar and behind the media

guide bar.

Media guide bar

Supplement

•The media must always be positioned over

the media sensor.

•See "Aligning the Push Rollers" P.09

about the position of the push rollers.

•See "Aligning the Push Rollers" P.09 for

information about center 3 push roller hold-

down force.

7Position the media and the push rollers to correspond with the width of the media.

Use the 5 push rollers to push down the sides and center of the media.

Use the grit roller position guide and make sure the push rollers are on top of the

grit rollers.

You can adjust the center push roller's hold-down force.

Grit roller position guide

Media sensor

Push roller

Grit roller

Push roller

(The center push roller is near the edge.)

(The push roller is on top of the grit roller.)(The push roller is on top of the grit roller.)

CAUTION

When setting on inside more than 30 mm, cut

cross is not available.

When Feeding Long-axis Media (at exceeds 2 meters)

Position the push rollers at least 15 mm inside the edges of the media.

Push roller

Media

15mm 15mm

CAUTION

When setting on inside more than 30 mm, cut

cross is not available.

When Feeding Long-axis Media (at least 2 meters)

Position the push rollers at least 5 mm inside the edges of the media.

Push roller

Media

5mm

To use a paper wider than 1,119 mm

Carefully set the position of the left edge of the push roller.

Set the right edge of the grit roller between 2 mm and 8 mm.

It's not possible to set the right edge of the grit roller to a size greater than 8 mm. (There is a stopper.)

CAUTION

Notes on the left grit roller

• The left grit roller is not available in all locations.

• It’s not possible to set the right edge of the grit roller to a size greater than 8 mm. (There is a stopper.)

• Please set the push roller to the position between 2 mm and 8 mm from the right edge of the grit roller.



Push roller

Grit roller

Media

Push roller

Grit roller

Media

8 mm or more

OK NG

CAUTION

During a plotting or cutting operation, be sure

to keep your hands, hair, and so forth away

from the media stocker, gears and rollers.

8 Raise the lever to lock.

Lever

9 When removing the paper, please stand to the side of the main assembly and

pull horizontally from the middle of the paper.

10 Pull from the front of the machine to even the tension of both A and B

sides of the paper, as shown in the gure below.

2 mm to 8 mm

5mm

11 Raise the set lever after conrming that the route the roll paper passes through

is taut and not slackening. The push roller position and the roll paper will stay in

place.

Media set lever

CAUTION

During a plotting or cutting operation, be sure

to keep your hands, hair, and so forth away

from the media stocker and collar.

12 Lowering the lever releases the stopper lock.

3. Aligning the Push Rollers

This section describes how to alignment of the push rollers.

Aligning the Push Roller

Position the left and right push rollers to correspond with the width of the media. Adjust the push rollers so that they are positioned above both

the media and the grit rollers.

Position the push rollers within the grit roller position guides ensures that they are above the grit rollers.

Push roller

Grit roller

Grit roller position guide

(It isn't on the grit roller.) (It isn't on the grit roller.)

CAUTION

To move the push rollers, the media set lever must be in the lowered position.

Supplement

If a [conrming push roller point] message appears after setting the media and raising the media set lever, it means the right push

roller is not on the right grit roller, or that the left or center 3 push rollers are not on the proper grit roller. Make sure everything is

set correctly.

CAUTION

•The media must be at least 125 mm in length

in media feed direction.

•The media must always be positioned over

the media sensor.

For minimum width media

The CE6000-120AP can take media of 594 mm (A1 size) or more.

Changing the Hold-down Force

The down force applied by the middle 3 push rollers can be changed depending on the width and type of media used.

When using the genuine Graphtec paper, please set the force of the middle push roller to "Normal" and the remaining 2 rollers to "Low" (OFF).

Media sensor

Grit roller

Push roller

Left-hand push roller

Right-hand push roller

Normal

Low (OFF)

CAUTION

Hold-down force can not be switched for side

push rollers.

Supplement

Switch the hold-down force as necessary for

different types of media.

Switching

(1) Lower the media set lever to raise the push rollers.

(2) Use the push roller hold-down force switching lever on the back of the push roller to

adjust the center push roller's hold-down force. It can be set to Normal or Low (OFF).

(3) When the push roller hold-down force switching lever is up, it is in Normal menu.

When it is down, it's Low (OFF).

Hold-down force:

Normal

Hold-down force:

Low (OFF)

Lever Lever

4. About the Initial Setup screen

The Initial Setup screen appears only when powering up the Cutting Plotter for the rst time after purchase. Here, you can set "Display

Language" and "Length Unit".

After the initial setup is completed, you can also select the menu from the READY status.

See "2.6 Connecting to the Power" P.2-20 for turning on the power.

1 Once the machine is powered on (with the " | " switch) a message will be displayed after the version is displayed.

DISPLAY LANGUAGE setting screen is displayed.

2 Use the POSITION ( ) keys to select the language.

(This manual assumes you chose the English language setting.)

Altri manuali per CE6000-120AP

Indice

Altri manuali GRAPHTEC Plotter

GRAPHTEC

GRAPHTEC MP303-04 Manuale utente

GRAPHTEC

GRAPHTEC FC2250 Series Manuale utente

GRAPHTEC

GRAPHTEC Craft ROBO CC100 Manuale utente

GRAPHTEC

GRAPHTEC OPS675 Manuale utente

GRAPHTEC

GRAPHTEC CELITE-50 Manuale utente

GRAPHTEC

GRAPHTEC Craft ROBO CC100 Guida utente

GRAPHTEC

GRAPHTEC CE6000-120AP Manuale utente

GRAPHTEC

GRAPHTEC CE5000-120AP Manuale utente

GRAPHTEC

GRAPHTEC FC9000-75 Manuale utente

GRAPHTEC

GRAPHTEC CE6000 SERIES Manuale utente

GRAPHTEC

GRAPHTEC Craft ROBO CC100-20 Manuale di programmazione

GRAPHTEC

GRAPHTEC Cutting PRO FC2230 Series Manuale utente

GRAPHTEC

GRAPHTEC FC8600 SERIES Manuale utente

GRAPHTEC

GRAPHTEC CE3000-120 Manuale utente

GRAPHTEC

GRAPHTEC FC8000 Series Manuale utente

GRAPHTEC

GRAPHTEC FC4200-50 Manuale utente

GRAPHTEC

GRAPHTEC FC4100 series Manuale utente

GRAPHTEC

GRAPHTEC Craft ROBO CC200 Guida utente

GRAPHTEC

GRAPHTEC FC9000 Series Manuale utente

GRAPHTEC

GRAPHTEC CE7000-130AP Guida utente

GRAPHTEC

GRAPHTEC Craft ROBO CC200 Manuale utente

GRAPHTEC

GRAPHTEC CC300-20 Craft ROBO Manuale utente

GRAPHTEC

GRAPHTEC CE6000 SERIES Manuale utente

GRAPHTEC

GRAPHTEC FC8600 SERIES Guida utente

Manuali Plotter popolari di altre marche

MUTOH

MUTOH Kona 760 Manuale utente

HP 7475a Manuale utente

Vulcan-Hart

Vulcan-Hart FC-500VC Manuale utente

Roland

Roland TrueVIS VG-640 Manuale del proprietario

Furuno

Furuno RP-180 Manuale utente

Roland

Roland VersaCamm SP-540V Manuale utente

MIMAKI

MIMAKI CF2 Series Manuale utente

Ioline

Ioline Summit Manuale utente

Summa

Summa S CLASS Manuale utente

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuale utente

Furuno

Furuno RP-17 Manuale utente

HP 7470A Manuale utente

SII

SII LP-1010 Manuale utente

Great Computer

Great Computer JII-61 Manuale utente

Roland

Roland VersaUv LEF - 12i Manuale utente

Lectra

Lectra Alys 120 Manuale utente

MUTOH

MUTOH Ultima SC-850D Manuale utente

Skycut

Skycut D Series Manuale utente