GRAPHTEC FCX4000 SERIES Manuale utente
USER’S MANUAL
MANUAL NO.FCX4000-UM-151
FCX4000 SERIES
CUTTING PLOTTER
i
TO ENSURE SAFE AND CORRECT USE
•To ensure the safe and correct use of your machine, read this manual thoroughly prior to use.
•After reading this manual, keep it in a handy location for quick reference as necessary.
•Do not allow small children to touch the machine.
•The following describes important points for safe operation. Be sure to observe them strictly.
Conventions Used in This Manual
To ensure the safe and accurate use of the machine as well as to prevent human injury and property
damage, the safety precautions provided in this manual are ranked in the three categories described below.
Their display and meaning is as following. Be sure to gain a full understanding of the meaning of them before
reading the Manual.
DANGER
This category provides information that, if ignored,
is highly likely to cause fatal or serious injury to the
operator.
WARNING
This category provides information that, if ignored, is
likely to cause fatal or serious injury to the operator.
CAUTION
This category provides information that, if ignored,
could cause injury to the operator or damage to the
machine.
Description of Safety Symbols
The symbol indicates information that requires careful
attention (including warnings). The specic point requiring
attention is described by an illustration or text within or next
to the symbol.
The symbol indicates an action that is prohibited. Such
prohibited action is described by an illustration or text within
or next to the symbol.
The symbol indicates an action that must be performed.
Such imperative action is described by an illustration or text
within or next to the symbol.
I
Preface
Thank you for choosing a Graphtec FCX4000 Series cutting plotter.
The FCX4000 Series cutting plotters employ a digital servo drive system to achieve high-speed and high-
precision cutting.
To ensure high cutting quality and optimal productivity, be sure to read this User's Manual thoroughly prior to use.
Notes on this Manual
(1) No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, without the prior written permission of Graphtec Corporation.
(2) The product specications and other information in this manual are subject to change without notice.
(3) While every effort has been made to provide complete and accurate information, please contact your sales
representative or nearest Graphtec vendor if you nd any unclear or erroneous information or wish to make
other comments or suggestions.
(4) Not with standing the stipulations in the preceding paragraph, Graphtec Corporation assumes no liability for
damages resulting from either the use of the information contained herein or the use of the product.
Registered Trademarks
All names of companies, brands, logotypes, and products appearing in this manual are the trademarks or
registered trademarks of their respective companies.
Copyright
This User's Manual is copyrighted by Graphtec Corporation.
II
Special Precautions on Handling Blades
Sharp cutter blades are used with this plotter. Handle the cutter blades and plungers with care to prevent bodily
injury.
The cutter blade must be discarded correctly according to local regulations/laws.
Cutter Blades
Cutter blades are very sharp. While handling a cutter blade or cutter pen, be careful to avoid cutting your ngers
or other parts of your body. Promptly return used blades to the cutter case provided.
Blade tip
When the case is completely lled, discard the used blades together with the case.
Cutter Plungers
The tip consists of a sharp blade. Be sure not to extend it too far. Moreover, when you are not using the cutter
plunger, make sure that the blade is fully retracted.
Cutter blade
After Mounting the Cutter Pen
After the power has been turned on, and during operation, do not touch the pen tip. It is dangerous.
III
After Turning on the Cutting Plotter
During operations, immediately after completion of operations, and when setting the cutting plotter functions,
the pen carriage, Y bar, and other parts which are not xed, may move suddenly. Do not let your hands, hair, or
clothing get too close to the moving parts or within their range of movement. Do not place any foreign objects in
or near these areas either. If your hands, hair, clothing, or the like get caught in, or wrapped around moving parts,
you may be injured and the machine may be damaged.
Machine Caution Label
The following Warning Label is located on this cutting plotter. Please observe all the warning on the label.
Precautions for electrostatic panel
If you accidentally cut the electrostatic panel surface, you may get an electric shock.
In this case, contact your sales representative or nearest Graphtec vendor.
Although you may feel rubber smell, it is not a malfunction of the product. As you use it, the smell gradually
reduces.
There may be the bloom on the surface of the electrostatic panel. In this case, wipe the panel surface gently with
a dry, soft cloth.
Be careful not to adhere the neutral detergent to the panel surface. If it adheres, electrostatic adsorption is
decreased or lost.
IV
About the words and phrases in this text
• In this instruction manual, the word "plot" refers to operating the machine and using either the plotting pen or the
cutter plunger to cut.
• In this instruction manual, the word "media" refers to paper, roll media, sheet media, or marking lm.
Prior to use
Be sure to read the attached TO ENSURE SAFE AND CORRECT USE prior to use. Otherwise, it may cause an
unexpected accident or re.
Precautions when using the curled media
If the media oats, secure the four corners using a drafting tape.
When the media is oating, if the plunger tip (cutter blade or ballpoint pen) has contact with it, it can affect the
nish quality.
Or, the cutting plotter body might be damaged.
Please x the warping of the media, or do not use the warped media.
V
Installation Space
Please secure a space for installation as according to the below illustration.
CAUTION
• Leavesufcientspaceforoperationsinfrontofandbehindthecuttingplotter.
• Wheninstallingonadeskorthelike,pleaseuseadeskwithsufcientstrength.Shakeofthedeskatthetimeofoperation
canaffectthenishquality.
100mm
500mm
600mm 600mm
VI
WARNING
The United States Federal Communications Commission has specied that the following notice must be
brought to the attention of users of this product.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USE SHIELDED CABLES
To comply with FCC Class A requirements, all external data interface cables and connectors must be
properly shielded and grounded. Proper cables and connectors are available from GRAPHTEC’s authorized
dealers or manufacturers of computers or peripherals. GRAPHTEC is not responsible for any interference
caused by using cables and connectors other than those recommended or by unauthorized changes or
modications to this equipment. Unauthorized changes or modications could void the user’s authority to
operate the equipment.
Altri manuali per FCX4000 SERIES
3
Indice
Altri manuali GRAPHTEC Plotter
GRAPHTEC
GRAPHTEC CE5000-120AP Manuale utente
GRAPHTEC
GRAPHTEC CE2000-60 Manuale utente
GRAPHTEC
GRAPHTEC FC8600 SERIES Manuale utente
GRAPHTEC
GRAPHTEC FC7000-75 Manuale utente
GRAPHTEC
GRAPHTEC FC8000 Series Manuale utente
GRAPHTEC
GRAPHTEC FC3100-120 Manuale utente
GRAPHTEC
GRAPHTEC CC300-20 Craft ROBO Manuale utente
GRAPHTEC
GRAPHTEC Craft ROBO CC100 Manuale utente
GRAPHTEC
GRAPHTEC CE6000 SERIES Manuale utente
GRAPHTEC
GRAPHTEC CE7000-130AP Guida utente
GRAPHTEC
GRAPHTEC Craft ROBO CC100 Guida utente
GRAPHTEC
GRAPHTEC FC4200-50 Manuale utente
GRAPHTEC
GRAPHTEC FC9000 Series Guida utente
GRAPHTEC
GRAPHTEC CE LITE-50 Manuale utente
GRAPHTEC
GRAPHTEC OPS675 Manuale utente
GRAPHTEC
GRAPHTEC CE5000-40CRP Manuale utente
GRAPHTEC
GRAPHTEC Craft ROBO CC200 Guida utente
GRAPHTEC
GRAPHTEC FC8600 SERIES Guida utente
GRAPHTEC
GRAPHTEC CE7000-130AP Manuale utente
GRAPHTEC
GRAPHTEC FCX4000 SERIES Guida utente
