GReddy e-01 Manuale utente
Instruction Manual
e-01英語版03.3.1920:28ページ1
1. Important Information
Warning!
• Installation and tuning of this product should only be
performed by a trained specialist who is very familiar with
the automobile s mechanical, electrical and fuel
management systems. If installed by an untrained person, it
may cause damage to the unit as well as the vehicle.
• When mounting this product in the vehicle, be sure the
unit does not interfere with the driver s view and normal
operation of the vehicle.
• When using soldering iron and other tools for installation,
be sure you read and understand the tool’s user manual first.
Misuse of these tools may cause injuries.
• When working on the electrical wires, make sure to
disconnect the negative terminal side of the battery on the
vehicle.
• When increasing the boost, be sure not to overboost.
Overboosting may cause damage to the engine.
• Be sure to find out what the safe boost pressure is for
your vehicle.
• GReddy Performance Products, Inc. is not responsible for
any engine damage caused by overboosting (increased
boost).
• Never tune the e-manage while the vehicle is moving.
• Never tune the e-Manage on public highway. This may
be dangerous to you as well as others on the road.
• When tuning and operating the vehicle in a garage, be
sure that the garage is equipped with a proper ventilation
system.
• After installation and tuning, be sure to clean up everything
that would interfere with the driver. Wires, tools and/or
communication cable may interfere with the driver and may
cause accidents.
Please read this instruction manual carefully and proceed with
the installation ONLY if you fully understand this manual. Make
sure to pay close attention to all the "Important!", "Warning!" and
"Caution!" messages throughout the manual.
Important!
• This product is legal for sale or use in California only on
vehicles which may never be driven on a public highway.
• This product is only for vehicles with 12V (battery) systems.
1
e-01英語版03.3.1920:28ページ2
1. Important Information
Caution!
•Improper tuning of the e-Manage may cause damage to the
engine.
•GReddy Performance Products, Inc. will not be responsible for
any damage caused by improper installation or tuning.
•Tuning should be performed only by a experienced technician
who fully understands the vehicle’s fuel management and
ignition timing requirement for the engine being tuned.
•Always use a proper air/fuel ratio meter when tuning the e-
Manage.
•Installation of this product requires modification of the vehicle’s
electrical system.
•When making wire connections, be sure to remove the key from
the ignition, and disconnect the negative terminal of the battery.
•Never short out the system. It can damage the unit as well as
the vehicle’s electrical system.
•Read and fully understand the wiring diagram before making any
wire connection.
•When connecting the connector, push it in all the way until you
hear them click in together.
•The communication cable is not a repairable item, so please
take care of it.When disconnecting from the PC (laptop), pull
holding the connector. Never pull on the cord.
2
e-01英語版03.3.1920:28ページ3
2. Parts List
3
Display unit Controller Center unit
Controller holder Display base Display bracket
Power harness 1/4 Cap bolt Double sided tape
Hex wrench (3mm) Hex wrench (5mm) M4 CAP bolt x2
M4 nut x2
SD card Instruction Manual Valve unit
e-01
e-01英語版03.3.1920:28ページ4
2. Parts List
Important!
The Display unit is packaged with the SD card already inserted.
4
Tools required for installation:
•Voltage tester •Wire cutters
•Pliers •Screw drivers (+,-)
•10mm wrench •Solder and Soldering iron
•Electrical tape •Zip ties
Pressure sensor Valve unit harness Pressure harness
(2.5m) (2.5m)
6øHose fitting x2 Hose clamp Three way fitting
Rubber washer 4øHose (1m) 6øHose (1m)
M4 Bolt M6 Bolt x2 Valve bracket
e-01英語版03.3.1920:28ページ5
3. Product Features
5
•The Display unit features a large LCD with EL backlighting.
•Three large easy to read data can be displayed in real time;
such as boost pressure, rpm, etc.
•Air/fuel ratio, throttle position and vehicle speed may be
displayed with the use of an optional Signal harness
(sold separately).
•The GReddy Warning gauge data can be displayed with the
use of an optional data link cable (sold separately).
•Built-in Warning feature for all input signals; such as boost,
rpm, etc.
•Link up to e-Manage to tune and save using Standard A/B
USB cable (available through any computer supply retailer).
•Able to record up to 3 hours of data and play back on the
display.
•Controls boost up to 3kg/cm (Depending on the turbo system).
Select from Auto and Manual boost mode to boost up to a
desired pressure.
•Boost pressure may be adjusted at different rpm points to
achieve consistent boost levels.
•Uses compact high volume solenoid valve.
•Uses high quality pressure sensor.
•Able to lower the boost pressure when the warring feature is
activated.
•Boost pressure may instantly be increased by using the Over
Take Boost feature.This feature can be used with the
Optional Remote Switching System (sold separately).
Important!
Standard A/B USB cable is required in order to link the e-01 to
the e-Manage unit.This is available at any computer supply
retailer.
Pressure sensor
Engine
Turbo Valve unit
Air cleaner
Actuator
Fuel regulator
Intercooler
Center unit
Controller
Display unit
2
e-01英語版03.3.1920:28ページ6
Before Installation
6
•Make sure the engine has cooled down before working under
the hood.
•Take the key out of the ignition switch and disconnect the
negative terminal of the battery.
•Before mounting the Valve unit and the Pressure sensor,
be sure the supplied vacuum hose is long enough to reach
them.
•Locate the actuator/wastegate, factory boost controlling
solenoid valve, and fuel pressure regulator or true vacuum
source before installation.
Installation Diagram
Pressure sensorPressure sensor
EngineEngine
TurboTurbo Valve unitValve unit
Air cleanerAir cleaner
ActuatorActuator
Fuel regulatorFuel regulator
IntercoolerIntercooler
Center unitCenter unit
ControllerController
Display unitDisplay unit
Option (yellow)
Ground (black)
Power 12V (red)
RPM (brown)
e-01英語版03.3.1920:28ページ7
Installation Diagram
7
Diagram 1:Vehicle with factory boost controlling solenoid valve
Dual Port Actuator
Disconnect the connector and the vacuum lines off from the solenoid
valve and plug up the all the vacuum ports.
EngineEngine
TurboTurbo
Air cleanerAir cleaner
IntercoolerIntercooler
solenoid valve
Before
Pressure sensorPressure sensor
EngineEngine
TurboTurbo Valve unitValve unit
Air cleanerAir cleaner
IntercoolerIntercooler
solenoid valve
After
Be sure to plug up
Engine
Turbo
Air cleaner
Intercooler
solenoid valve
Pressure sensor
Engine
Turbo Valve unit
Air cleaner
Intercooler
solenoid valve
e-01英語版03.3.1920:28ページ8
Installation Diagram
8
Engine
Turbo
Air cleaner
Intercooler
solenoid valve
Pressure sensor
Engine
Turbo Valve unit
Air cleaner
Intercooler
solenoid valve
Diagram 2:Vehicle with factory boost controlling solenoid valve
Single port actuator
Disconnect the connector and the vacuum lines off from the solenoid
valve and plug up the all the vacuum ports.
EngineEngine
TurboTurbo
Air cleanerAir cleaner
IntercoolerIntercooler
solenoid valve
Before
Pressure sensorPressure sensor
EngineEngine
TurboTurbo Valve unitValve unit
Air cleanerAir cleaner
IntercoolerIntercooler
solenoid valve
After
Be sure to plug up
e-01英語版03.3.1920:29ページ9
Installation Diagram
9
Pressure Sensor Installation
Connector must
Point Down
Fuel pressure regulator
(1) Mount the Pressure sensor to the body near the fuel regulator
using the supplied bracket and bolt.
(2) Cut the vacuum line on the fuel regulator and install the
supplied three way-fitting.
(3) Place the supplied orifice to the side that will connect the
sensor and connect the 4øHose from the three way fitting to
the sensor.
Important!
•Make sure that the Sensor connector is pointed down as
shown in the diagram above.
•Make sure that the sensor is securely mounted on the body.
•Avoid mounting the sensor in the hot area or where it can get wet.
•Toyota’s JZ engines and Mitsubishi’s 4G63 engine have
fuel pressure controlling solenoid valves.For these vehicles,
make sure to get pressure from the line between the intake
manifold and the solenoid.
•Make sure to secure the 4øHose with zip ties.
Orifice
Intake Manifold
e-01英語版03.3.1920:29ページ10
Altri manuali per e-01
1
Indice
Altri manuali GReddy Controllori
