Greenlee Shear 30T Manuale utente

INSTRUCTION MANUAL

Shear 30T

Shearing Station

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Español................17–32

Français...............33–48

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Purpose of this Manual ................................................. 2

Safety ............................................................................ 3

Identication.................................................................. 4

Caster Mounting............................................................ 5

Die Loading/Changeover............................................... 6

Setting the Measurement Stop ..................................... 7

Operation....................................................................8–9

Cutting Strut Channel............................................... 8

Cutting Threaded Rod.............................................. 9

Maintenance................................................................ 10

Cutting Unit Mounting ................................................. 11

Exploded Views and Parts Lists.............................12–15

Cutting Unit........................................................ 12-13

Service Cart ....................................................... 14-15

Description

The Greenlee Shearing Station is used to shear

commonly branded, mild steel strut channel and

threaded rod products. This tool is not designed

to be used with stainless steel, aluminum or

berglass strut or threaded rod workpieces.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

Greenlee Shearing Station.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

All specications are nominal and may change as design

improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Read and understand all of the instruc-

tions and safety information in this

manual before operating or servicing

this tool.

Strut channel and threaded rod

ends can be sharp. Gloves are

recommended when handling

these materials.

Wear eye protection when operating or

servicing this tool. Failure to wear eye

protection could result in serious eye

injury from ying debris or hydraulic oil.

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards or

unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message after

the signal word provides information for preventing

or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in severe

injury or death.

Hazards or unsafe practices which, if not avoided, MAY

result in injury or property damage.

Skin injection hazard. Do not use

hands to check for oil leaks. Oil under

pressure easily punctures skin. If

injured, seek medical attention imme-

diately to remove oil. Failure to observe

this warning could result in serious

injury or death.

If operating the tool continuously for

more than 2 hours hearing protection

is recommended. Longterm exposure

to high noise levels could result in

hearing damage.

IMPORTANT SAFETY INFORMATION

Do not overload cart

Pinch points: Keep hands away from

the cutting unit during the shearing

process. Failure to observe this warning

could result in severe injury or death.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Identiﬁcation

1. Service Cart

2. Cutting Unit

3. Front Material Rest

4. Rear Channel Rest

5. Rear Rod Rest

6. Rear Arm Knob

7. Measurement Stop Knob

8. Extension Arms

9. Measurement Stop

10. Alloy Steel Cassette Frame

11. 30 Ton Hydraulic Ram with

Universal Coupling

12. Die Retaining Rails

13. End Stop

14. Mobile Die

15. Stationary Die

16. Swing Arm

17. Die Spacer

Speciﬁcations

Cutting Unit and Dies

For cutting 18, 16, 14 and 12 gauge mild steel strut channel of various nishes.

For cutting Grade 2 mild or low carbon steel threaded rod of various nishes.

Maximum Force................................................................................................. 30 tons

Hydraulic Pressure ........................................................................................10,000 psi

Service Cart

Dimensions.................................................................................. 19” W x 44” H x50” L

Shelf Size....................................................................................... 2” H x18” W x 36” L

Load Rating ......................................................................... 800 lbs, evenly distributed

12 11

The dies are not designed to cut stainless steel workpieces. Expect reduced die life if cutting this material.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Rotate the Service Cart on its side.

Attach the Rigid and Swivel Casters to the bottom

shelf of the Service Cart with the included caster

mounting hardware. Torque the nuts to 25 ft lbs.

Reposition the Service Cart with casters in its

upright position.

Transporting and Storage

Remove all dies from the Cutting Unit. Lower the Rear

Rod Rest and Measurement Stop. Center both Extension

Arms; lock the arms by tightening the Rear Arm Knob

and Measurement Stop Knob.

Connecting to Power Source

Attach your 10,000 psi rated pump to the Hydraulic

Ram’s universal coupler with a similarly rated hydraulic

hose. The Service Cart has an opening in its upper

shelf for the hose to feed through if the pump is seated

on the lower shelf. Tighten the hydraulic tting and

test cycle the Cutting Unit unloaded to conrm a

proper connection.

Caster Mounting

Cart is heavy, advise having two persons when

turning cart.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Die Loading/Changeover

If a die set is already loaded in the cutting unit, pull the

Swing Arm out of the Mobile Die and rotate it onto the

Die Spacer. Pull back the End Stop and slide out the

Mobile Die within the Cassette Frame, then push the

Stationary Die forward and slide it out also. Load the

new die set in a reverse matter. Be sure to reengage the

Swing Arm before beginning cutting.

Note: if having difculty removing or inserting dies, clear

debris from the Cassette Frame die pockets.

Note: it is recommended to apply a moly-base

spray lubricant to the die and frame working surfaces

whenever changing dies.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Setting the Measurement Stop

The Measurement Stop can be set to repeatedly cut

lengths from 12 to 48 inches. Turn the Measurement

Stop Knob holding down the Extension Arm counter-

clockwise to unlock. Set stop to required cut length by

moving the arm left or right as needed, then retighten the

knob. Raise or Lower the stop such that the workpiece

being cut just makes contact.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Operation

Cutting Strut Channel

When cutting strut channel, the work piece must always

be supported by the Front Material Rest. Do not cut

total channel lengths of less than 7.5” as they cannot be

properly supported and can cause a die to fracture.

Place the workpiece on the Front Material Rest and Rear

Channel Rest (if long enough) and push through the

Stationary and Mobile dies up to the Measurement Stop

(if being used) or to desired nished length. The Rear

Rod Rest should be lowered out of the way. Activate the

hydraulic pump to begin the cut cycle. Wait for the strut

to shear then release the hydraulic pressure. The Mobile

Die will return to its original position to begin another cut.

Lower the Measurement Stop and unload the nished

workpiece, then return the stop for the next cut.

Note: cutting nished lengths of less than 2 inches may

warp the channel prole.

Note: the Rear Channel Rest was designed to support

up to 10ft workpiece lengths. Additional support may be

required when cutting lengths longer than this.

Engage caster brakes before operating unit.

When cutting short pieces of strut channel the

nished workpiece can pop out due to the shock

of the cutting cycle, always wear safety glasses.

Shearing across holes and slots can leave sharp

points on nished workpieces.

Do not cut single box strut workpieces with the

double strut dies, the dies will fail quickly.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Operation (cont’d)

Cutting Threaded Rod

Push the workpiece through the Stationary and Mobile

Dies up to the Measurement Stop (if being used) or

to desired nished length. The Rear Rod Rest can be

raised to support longer workpieces. Firmly seat the

rod against the threads of the Stationary Die and keep

the workpiece perpendicular to the dies. Activate the

hydraulic pump to begin the cut cycle. Wait for the rod

to shear then release the hydraulic pressure. The Mobile

Die will return to its original position to begin another

cut. Lower the Measurement Stop and unload the

nished workpiece, then return the stop for the next cut.

Note: The threaded rod dies have been designed so that

the nut threads onto the cut rod by hand. Thread quality,

surface nish (i.e., galvanized or plated), dirt and scale

could affect the ability of the nut to thread freely onto the

cut rod.

Filing of the rod end or use of a pliers may be necessary

if nut does not easily thread on due to these factors.

Note: The Rear Rod Rest was designed to support

single workpieces up to 10ft lengths. Additional support

may be required when cutting lengths longer than this or

multiple pieces at once.

Tip: If a nut begins to thread and locks up, tapping

it on a surface will often loosen it and allow

continued threading.

Finished workpiece length should not be less than .25”.

Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Maintenance

Lock out power to the Cutting Unit before performing any maintenance.

Change the hydraulic oil annually or after 10,000 cycles. Use ASTM 215 hydraulic uid (or equal).

At least monthly, clean the inner track portions of the Cassette Frame and Die Retaining Rails. Apply a moly based,

spray lubricant to the working surfaces. A dry lm lubricant such as Molykote 557 is recommended.

The material cutting dies are wear parts and will fail over time. Order additional dies through Greenlee distributors.

The unit experiences a shock during each cutting cycle which can loosen bolt connections over time. Periodically

check all fasteners on the Cutting Unit and retighten where needed.

Available Dies

Note: The hot-dipped galvanized nished available from many manufacturers will often leave beads of nish on the

product and can be more difcult to get through dies.

KEY CAT NO. DESCRIPTION COMPATIBILITY

1 1316SSTRT 13/16 X 1-5/8 Single box prole B-Line B52, B54, & B56

Unistrut P4520, P4100, & P4000

Powerstrut PS 520 & PS 500

Superstrut A-1400 & B-1400

2 158STRDSTRT 1-5/8 x 1-5/8 Single box prole B-Line B22, B24, & B26

Unistrut P1000, P1100, & P2000

Powerstrut PS 200 & PS 210

Superstrut A-1200 & B-1200

3 158SSTRT 13/16 x 1-5/8 & 1-5/8 x 1-5/8 Single

box proles B-Line B22, B24, B26 & B52, B54, B56

Unistrut P1000, P1100, P2000 & P4520, P4100, P4000

Powerstrut PS 200, PS 210 & PS 520, PS 500

Superstrut A-1200, A-1400 & B-1200, B-1400

4 158DSTRT 1-5/8 X 1-5/8 Double box back to

back proles B-Line B22A, B24A, B26A

Unistrut P1001, P1101, P2001

Powerstrut PS 200 2T3, PS 210 2T3

Superstrut A-1202 & B-1202

5 4STRT21 1-1/16 x 2-1/8 Single box 4D proles B-Line 4D21

6 4STRT22 2-1/8 x 2-1/8 Single box 4D proles B-Line 4D22

7 1458TROD 1/4-20, 3/8-16, 1/2-13 & 5/8-11 Threaded Rod All mild steel rod

Altri manuali per Shear 30T

Indice

Lingue:

Altri manuali Greenlee Taglierina

Greenlee

Greenlee 645-3/4 Manuale utente

Greenlee

Greenlee GATOR ESR1000LX Manuale utente

Greenlee

Greenlee GATOR ESG85GL Manuale utente

Greenlee

Greenlee ES32FML Manuale utente

Greenlee

Greenlee ES20LXR Manuale utente

Greenlee

Greenlee GATOR ESG45GL Manuale utente

Greenlee

Greenlee GATOR Plus ESG50GL Manuale utente

Greenlee

Greenlee 764 Guida

Greenlee

Greenlee GATOR ETS8 Manuale utente

Greenlee

Greenlee 750 Manuale utente

Greenlee

Greenlee GATOR ETS12 Manuale utente

Greenlee

Greenlee ES750 Manuale utente

Greenlee

Greenlee ESC85 Manuale utente

Greenlee

Greenlee Gator ES20HVX Manuale utente

Greenlee

Greenlee 763 Manuale utente

Greenlee

Greenlee ES750 Manuale utente

Greenlee

Greenlee GATOR ESG45L Manuale utente

Greenlee

Greenlee GATOR EK425LXCJACSR Manuale utente

Greenlee

Greenlee GATOR ES1000 Manuale utente

Greenlee

Greenlee C3 Auto Whip Clad Cable Cutter Manuale utente

Greenlee

Greenlee ESG65LXR Manuale utente

Greenlee

Greenlee GATOR ES32 Manuale utente

Greenlee

Greenlee GATOR CSG85GL Manuale utente

Greenlee

Greenlee ESG65LXR11 Manuale utente

Manuali Taglierina popolari di altre marche

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuale utente

Makita

Makita DCS552 Manuale utente

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuale utente

Makita

Makita 4112HS Manuale utente

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuale utente

Hitachi

Hitachi CM 4SB2 Guida alla risoluzione dei problemi

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuale utente

GCC Technologies

GCC Technologies AFJ-24S Manuale utente

DeWalt

DeWalt XR LI-ION DCS350N Manuale utente

Baudat

Baudat ES1 Manuale utente

Mafell

Mafell ZAF 200 Guida

Makita

Makita 4100NH Manuale utente

Formax

Formax FD 574 Manuale utente

EINHELL

EINHELL TE-MA 1500 Manuale utente

Husqvarna

Husqvarna Cut-n-Break K 760 Manuale utente

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuale utente

TRI tool

TRI tool 301A Manuale utente

Roller

Roller King 1 1/4 Manuale utente