Grizzly H8093 Manuale utente
Model H8093
21⁄2 Ton Low Profile
Garage Jack
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8824 PRINTED IN CHINA
Specifications
Maximum Lifting Capacity ................... 5000 Lbs.
Lifting Range ......................................33⁄8"–151⁄16"
Weight ................................................... 108 Lbs.
If you need help with the Model H8093, call our
Technical Support line at: (570) 546-9663.
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle with appro-
priately rated support stands before
working under it.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Operation
To raise the jack, rotate the pump valve knob
clockwise completely, then move the pump han-
dle or foot pump up and down. To lower the jack,
slowly rotate the pump valve knob counterclock-
wise.
Figure 1. Jack controls.
Pump
Handle
Pump Valve
Knob
Foot
Pump
Maintenance
Keep the hydraulic rams clean and free of any
dust, dirt, or foreign debris. Abrasive material
stuck to the ram can damage the hydraulic seal
when the ram is retracted back into the jack.
Regularly wipe the hydraulic rams clean with a
lightly oiled rag.
The Model H8093 will require hydraulic fluid after
long-term use. This will be noticeable if the jack
will not reach its maximum height when pumped.
Only use a high quality hydraulic fluid.
To add hydraulic fluid:
1. Completely lower the jack.
2. Remove the top cover plate from the jack and
remove the fill plug shown in Figure 2.
Bleeding the Air
If the jack becomes spongy or will not rise when
pumped, then air bubbles may be in the hydraulic
system.
To remove the air bubbles:
1. Remove the fill plug.
2. Rotate the pump valve knob counterclock-
wise one full turn.
3. Pump the jack quickly ten times to purge the
air from the system.
4. Replace the fill plug and test the operation of
the jack.
—If the jack did not perform properly, then air
may need to be bled from the pump system
again.
3. Add fluid until it reaches the top of the fill plug
hole.
4. Replace the fill plug.
5. Test the operation of the jack by pumping
it up to the maximum height and applying a
load. The jack should hold the weight of the
load without a sinking or spongy feeling.
—If the jack did not perform properly, then
air may need to be bled from the pump
system.
Figure 2. Fill plug.
Fill Plug
H8093 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH8093001 COVER 27 PH8093027 SUPPORT ROD
2 PN09M HEX NUT M12-1.75 28 PH8093028 TORSION SPRING
3 PH8093003 FENDER WASHER 12MM 29 PH8093029 EXTENSION SPRING
4 PH8093004 FRONT WHEEL SLEEVE 30 PH8093030 PUMP ASSEMBLY
5 PH8093005 FRONT WHEEL 31 PH8093031 FOOT PEDAL
6 PH8093006 LEFT FRAME 32 PS14M PHLP HD SCR M6-1 X 12
7 PH8093007 RUBBER PAD 33 PH8093033 PEDAL BASE
8 PH8093008 SADDLE 34 PH8093034 IDLER WHEEL
9 PH8093009 LIFTING ARM ASSEMBLY 35 PH8093035 IDLER WHEEL SHAFT
10 PH8093010 FRONT WHEEL AXIS 36 PH8093036 TORSION SPRING
11 PH8093011 CONNECTING ROD AXIS 37 PH8093037 HANDLE SOCKET
12 PH8093012 LONG CONNECTING ROD 38 PB35M HEX BOLT M12-1.75 X 40
13 PR06M EXT RETAINING RING 16MM 39 PW06M FLAT WASHER 12MM
14 PH8093014 RIGHT FRAME 40 PH8093040 OPERATION HEAD
15 PH8093015 CONNECTING ROD 41 PH8093041 OPERATION ROD 2
16 PLW06M LOCK WASHER 10MM 42 PH8093042 COTTER PIN 4 X 26MM
17 PN02M HEX NUT M10-1.5 43 PH8093043 COTTER PIN 3 X 16MM
18 PS26M PHLP HD SCR M6-1 X 20 44 PH8093044 OPERATION ROD 1
19 PH8093019 AXIS FOR PUMP 45 PH8093045 COTTER PIN 3 X 28MM
20 PB20M HEX BOLT M8-1.25 X 35 46 PH8093046 PUMP VALVE KNOB
21 PR11M EXT RETAINING RING 25MM 47 PH8093047 LOWER HANDLE
22 PLW05M LOCK WASHER 12MM 48 PS03M PHLP HD SCR M6-1 X 8
23 PLW12M LOCK WASHER 18MM 49 PH8093049 UPPER HANDLE
24 PH8093024 CONNECTING BOLT 50 PH8093050 MACHINE ID LABEL
25 PH8093025 REAR CASTER ASSEMBLY 51 PH8093051 FILL PLUG
26 PS29M PHLP HD SCR M12-1.75 X 25
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
unreadable, contact Grizzly at (800) 523-4777 or www.grizzly.com to order a new label.
Indice
Altri manuali Grizzly Utensili elettrici
Grizzly
Grizzly G8621 Manuale utente
Grizzly
Grizzly G0452 Manuale utente
Grizzly
Grizzly G0768 Manuale utente
Grizzly
Grizzly G0779 Manuale utente
Grizzly
Grizzly G5912Z Manuale utente
Grizzly
Grizzly G8622 Manuale utente
Grizzly
Grizzly G0490 Guida rapida
Grizzly
Grizzly G1035 Manuale utente
Grizzly
Grizzly H6136 Manuale utente
Grizzly
Grizzly G8689 Guida rapida
Grizzly
Grizzly G0452 Manuale utente
Grizzly
Grizzly G0656 Manuale utente
Grizzly
Grizzly G4179 Manuale utente
Grizzly
Grizzly G0480 Guida rapida
Grizzly
Grizzly G1182HW Manuale utente
Grizzly
Grizzly G5912Z Guida rapida
Grizzly
Grizzly Power Feeder G4176 Manuale utente
Grizzly
Grizzly AGS 720 Lion-Set Istruzioni per l'uso e l'installazione
Grizzly
Grizzly G0796 Manuale utente
Grizzly
Grizzly G0678 Manuale utente
