Grotime BACKSAVER Manuale utente
Two adults required to assemble this cot.
!
The manufacturer's assembly instructions must be followed
in detail to ensure the safet
y features to the cot are not compromised.
!
3 in 1 cot with drawer
BACKSAVER
x1
AllenKey
HG
x4
70mm Bolts
HB
x8
50mm Bolts
HA
x10
35mm Bolts
HF
GuidePins
HC
Wood Pins
HE
HARDWARE INVENTORY
COT DRAWER
PRE-INSTALLED HARDWARE
PARTS LIST
2
Locking Bolts WoodScrews
2xEndPanels
PB
1x Fixed Side
PA
1 x Drop Side
PC
1x Cot Base
PD
2xBottom Plates
2xDrawer Sides
1xBottom Plate Holder
DB
2xDrawer Runners
DA
1x FrontEnd
DD
DC
1x Back End
DE DF
x2
Drawer Stop Set
HH
x4 x8x8
Bolts&Cap Nuts
HD
LOW
Toddler level
STEP 1
ASSEMBLE COT DRAWER RUNNERS
IN THE COT ENDS
STEP 2
Screw Driver
3
ASSEMBLE THE TWO OUTER
ENDS TO THE BASE
Do not tighten bolts
at this stage
!
HIGH
Bassinet level
Chose high or low
position for mattress base
!
x2 x2
End Panels
PB
x2 x1
End Panels
PB
Cot Base
PD
Drawer Runners
DA
x8
50mm Bolts
HA
STEP 3
ASSEMBLE FIXED SIDE TO ENDS
SCREW FOUR GUIDE PINS
INTO ENDS FIRMLY
STEP 4
4
Do not tighten bolts at this stage
!
x4
Guide Pins
HC
Screw Driver
x1
Fixed Side
PA
x4
70mm Bolts
HB
STEP 5
ASSEMBLE DROP SIDE
FULLY SCREW IN LOCKING BOLTS
STEP 6
x1
Drop Side
PC
5
Ensure correct side is facing out.
Align two access holes in the built-in
runner with the guide pins on one end.
Now repeat on other end.
!
Lift drop side up until it clicks
into the locking position.
b.
a.
To lower drop side, lift from centre of top rail, hold side in that position while using your leg to push inward on
centre of bottom rail. Then allow to slide gently down.
OPERATION
STEP 7
TIGHTEN ALL BOLTS AND
STEP 8
6
1.
2.
3.
HOW TO OPERATE DROP SIDE OF THIS COT
ϭͿ>ŝŌƐŝĚĞƵƉƵƐŝŶŐƚŽƉƌĂŝů
ϮͿWƵƐŚďŽƩŽŵƌĂŝůŝŶǁĂƌĚƐǁŝƚŚůĞŐ
ϯͿ>ŽǁĞƌƚŚĞƐŝĚĞŐĞŶƚůLJƚŽƚŚĞůŽǁĞƌƉŽƐŝƟŽŶ
dŽƌĂŝƐĞƐŝĚĞ
>ŝŌƐŝĚĞƵŶƟůŝƚĐůŝĐŬƐŝŶƚŽƚŚĞůŽĐŬĞĚƵƉƉĞƌƉŽƐŝƟŽŶ
Remove dropside by reversing to step 4.
Day Bed
DAY BED CONVERSION
COT BED CONVERSION
Remove dropside by reversing to step 4.
a.
b.
7
Cot Bed
Remove dropside guide pins (HC) from the ends to prevent injury.
!
ASSEMBLE THE BACK END TO SIDES
STEP 2
INSERT WOOD PINS INTO THE DRAWER SIDES
STEP 1
DRAWER ASSEMBLY
x4 x2
Wood Pins
HE
Drawer Sides
DB
x4 x1
35mm Bolts
HF
Back End
DE
8
ASSEMBLE THE BOTTOM PLATE HOLDER TO BACK END
STEP 3
INSERT THE BOTTOM PLATES
STEP 4
x1 x1
35mm Bolts
HF
Bottom Plate Holder
DC
x2
Bottom Plates
DF
9
INSERT WOOD PINS INTO THE FRONT END
STEP 5
ASSEMBLE THE FRONT END
STEP 6
x4 x1
Wood Pins
HE
Front End
DD
x5
35mm Bolts
HF
10
Indice
Altri manuali Grotime Mobili per neonati e bambini piccoli
