Guardian G1902 Manuale utente
Safety Stations with Eyewash
FG1902 Safety Station with Eyewash, Stainless Steel Bowl
Application: Combination eyewash and shower safety
station. Two GS-Plus™ spray-type outlet heads deliver a flood
of water for rinsing eyes.
Shower Head: 10" diameter orange ABS plastic.
Shower Valve: 1" IPS chrome plated brass stay-open ball valve.
Valve is US-made with chrome plated brass ball and Teflon®
seals. Furnished with stainless steel actuating arm and 29"
stainless steel pull rod.
Spray Head Assembly: Two GS-Plus™ spray heads. Each head
has a “flip top” dust cover, internal flow control and filter to
remove impurities from water.
Eyewash Bowl: 11-1/2" stainless steel.
Eyewash Valve: 1/2" IPS chrome plated brass stay-open
ball valve. Valve is US-made with chrome plated brass ball and
Teflon® seals.
Pipe and Fittings: Schedule 40 galvanized steel. Furnished
with orange polyethylene covers for vertical piping for high
visibility and corrosion resistance.
Supply: 1-1/4" NPT female top or side inlet.
Waste: 1-1/4" NPT female outlet. Outlet can be positioned at
either 9-1/4" or 19-5/8" above finished floor by reversing lower
pipe nipples.
Sign: Furnished with ANSI-compliant identification sign.
Quality Assurance: Valve and spray head assemblies are
factory assembled and water tested prior to shipment.
Available Options
FGC Powder coated finish on galvanized Pipe and Fittings:.
Available colors include orange, yellow, red and green.
F
FC20 Regulates shower flow rate to 20 GPM.
FGRN Green ABS plastic shower head.
FYEL Yellow ABS plastic shower head.
FSSH Stainless steel shower head.
F
AP275-100 Electric Light and Alarm Horn
Light and alarm horn summon assistance when eyewash
or shower is activated.
FAP250-015 Modesty Curtain
Modesty curtain for mounting on safety station.
FTMV G3800LF thermostatic mixing valve precisely blends
hot and cold water to deliver warm (tepid) water as
required by ANSI Z358.1-2014.
Safety Stations with Eyewash
this space for architect/engineer approval
Due to continuing product improvement, the information contained in this document
is subject to change without notice. All dimensions are ± 1/4" (6mm).
Sign Included
FG1902 Safety Station with Eyewash, Stainless Steel Bowl
(152mm)
(165mm)
(127mm)
OPEN BALL VALVE
(1645mm)
PLATED BRASS STAY-
1/2" IPS CHROME
(235mm)
64 3/4"
BALL VALVE
BRASS STAY-OPEN
1" IPS CHROME PLATED
(610mm)
23 1/2"
(597mm)
24"
6 1/2"
5"
6"
Ø9"
(229mm)
9 1/4"
9 1/4"
(235mm)
NOTES:
1. EACH GS-PLUS SPRAY HEAD
HAS A "FLIP-TOP" DUST
COVER, INTERNAL FLOW
CONTROL AND FILTER TO
REMOVE IMPURITIES FROM
THE WATER FLOW.
2. REVERSING THE TWO LOWEST
PIPE NIPPLES RAISES THE
DRAIN OUTLET TO 19-5/8" A.F.F.
DETAIL "A"
UNIVERSAL FLOOR FLANGE
ON 7-5/8" BOLT CIRCLE
Ø7/16" MOUNTING SLOTS
POWDER COATED
CAST ALUMINUM
FLOOR FLANGE
(SEE DETAIL "A")
STAINLESS STEEL
PULL ROD
29"
(737mm)
89"
(2261mm)
1-1/4" NPT
FEMALE OUTLET
Ø10"
(254mm)
ABS PLASTIC
SHOWER HEAD
AND ELBOW
(2) GS-PLUS
SPRAY HEADS
POWDER-COATED CAST
ALUMINUM FLAG HANDLE
GALVANIZED STEEL
PIPE AND FITTINGS
1-1/4" NPT
FEMALE INLET
1-1/4" NPT
FEMALE INLET
(PLUGGED)
STAINLESS STEEL
ACTUATING ARM
37 1/2"
(953mm)
84"
(2134mm)
STAINLESS
STEEL BOWL
5 3/4"
(146mm)
Ø11 1/8"
(283mm)
Parts List
Safety Stations
Item Part Number Description
Shower Heads
AAP450-032ORG Orange ABS Plastic Shower Head
AP450-032GRN Green ABS Plastic Shower Head
AP450-032YEL Yellow ABS Plastic Shower Head
AP450-048 10” Dia. Stainless Steel Shower Head
Shower Head Elbows
B330-12-08RSE-OR Orange ABS Plastic Elbow
330-12-08RSE-GR Green ABS Plastic Elbow
330-12-08RSE-YE Yellow ABS Plastic Elbow
300-08SE 1” IPS Galvanized Steel Street Elbow
Shower Valve Assembly
CAP600-335H 1” IPS Chrome Plated Brass Stay-Open
Ball Valve, Single Activation. Furnished
with stainless steel actuating arm.
Galvanized Pipe Packs
DAP500-100 Galvanized Steel Pipe Pack for Units with
Eyewash Bowl
AP500-170 Galvanized Steel Pipe Pack for Barrier-
Free Units
AP530-100 Orange Pipe Covers
Eyewash Valve Assemblies
EAP600-101H 1/2” IPS Chrome Plated Brass Ball Valve
with Power Coated Aluminum Flag
Handle
AP600-101H-HFC 1/2” IPS Chrome Plated Brass Ball Valve
with Power Coated Aluminum Flag
Handle for Units with Hand/Foot Control
F150-032 Powder Coated Cast Aluminum Floor
Flange, 1-1/4” NPT Female Connection
GAP050-010 Stainless Steel Foot Treadle and Return
Spring with Aluminum Clevis Pin
HSee Page 2 Eyewash and Eye/Face Wash Assemblies
Shower Pull Rods
IAP050-079 29” Stainless Steel Pull Rod
AP050-080 47 1/2” Stainless Steel Pull Rod
B C
D
I
H
G
A
F
E
Parts List
Eyewash and Eye/Face Wash Assemblies for Safety Stations
C
B
B
B
D
E
Item Part Number Description
Spray Head Dust Covers
AAP470-001 GS-Plus™ Spray Head Assy.
AP470-021 FS-Plus™ Spray Head Assy.
Outlet Assemblies
BAP470-100R (2) GS-Plus™ Spray Heads with Chrome
Plated Brass Fittings
AP470-110R (2) FS-Plus™ Spray Heads with Chrome
Plated Brass Fittings
AP470-120R (4) GS-Plus™ Spray Heads with Chrome
Plated Brass Fittings
AP470-127R (4) GS-Plus™ Spray Heads with Chrome
Plated Brass Fittings for Barrier-Free
Units
BI136-02-04 3/8” IPS X 2-1/4” Brass Shank
Item Part Number Description
Bowls
C100-009ORG-R Orange ABS Plastic Bowl
100-009GRN-R Green ABS Plastic Bowl
100-009YEL-R Yellow ABS Plastic Bowl
100-008R Stainless Steel Bowl
100-014R Stainless Steel Bowl for Barrier-Free
Units
Drain Plate Assemblies
DAP150-012A Drain Plate Assembly for Plastic Bowls
AP150-012B Drain Plate Assembly for Stainless
Bowls
Note: Includes Drain Plate, Cupped Washer, And Gasket
Waste Receptor
E150-066-1R Waste Receptor with Flared Nipple
Coupling and Gasket, 1 1/2” NPT Male
Outlet
AA
A
Assembly Instructions
Safety Stations
A
B
C
O
P
Q
R
D
E
F
G
H
I
JKLMN
32” Nipple
16 5/8” Nipple 22” NIPPLE
10 1/2”
Nipple
8 7/8”
Nipple
Safety stations are designed for easy assembly in the field.
Essentially, these units are assembled from the “bottom up”,
as described below:
1. Assemble floor flange (A), 1 1/4” IPS x 6 1/4” nipple (B),
and plugged outlet tee (C). If unit has a foot treadle, the
floor flange and treadle are pre-assembled. Position foot
treadle for proper access by users, and tee for connection
to drain. IMPORTANT: Plugged tee (C) must be oriented with
plugged end down to assure proper drainage.
2. Assemble 1 1/4” IPS x 16 5/8” nipple (D) and frame
assembly (E). Position frame assembly for proper access by
users.
3. Assemble 1 1/4” IPS x 32” nipple (F) and inlet tee (G).
Position tee for connection to supply. If the top vertical
inlet will be employed, plug tee with supplied 1 1/4” IPS
square head plug.
4. Assemble 1 1/4” IPS x 22” nipple (H) and 1 1/4” x 1” IPS
reducing inlet tee (I). Position tee forward for proper
location of shower. If the back horizontal inlet will be
employed, plug tee with supplied 1 1/4” IPS square head
plug.
5. Assemble 1” IPS x 8 7/8” nipple (J), emergency shower
valve (K), 1” IPS x 10 1/2” nipple (L), elbow (M), and shower
head (N).
6. Place cupped, stainless steel washer (O), rubber gasket (P),
and bowl (Q) onto waste receptor. Center components to
assure a watertight seal.
7. Thread drain plate (R) down onto mounting shank as far
as possible. If neccessary, rotate bowl clockwise to draw
drain plate down onto mounting shank.
8. Thread eye or eye/face wash spray head assembly onto
mounting shank. Position outlet heads for proper access
by user.
9. Secure entire unit to floor and/or wall for stability.
10. If unit has foot treadle, connect foot treadle chain to
valve/handle assembly.
11. Attach orange plastic pipe wrap and sign.
Notes:
1. All threads are tapered pipe and require pipe joint
compound or Teflon tape to assure watertight connection.
2. If unit is furnished with corrosion-resistant powder
coating, care must be taken to avoid damaging finish
during assembly. For best results, a strap wrench should
be used.
3. Test the entire unit for proper operation.
4. The use of dielectric unions is required when connecting
to copper supply to avoid premature corrosion.
Parts List
GS-Plus™ and FS-Plus™ Spray Heads
Each spray head head features:
• Tough polypropylene plastic construction
• Highly visible integrated nylon dust cover
• Easily accessible 1.8 GPM (GS-Plus™) or 3.2 GPM (FS-Plus™)
flow controls.
• Dense (60 pore per inch) polyurethane filter
• Unique design provides a consistently soft, full spray of water
across a range of working pressures from 30 to 100 PSI
A
B
C
D
Item Part Number Description
AAP470-001 GS-Plus™ Spray Head (assembled)
BAP470-002R Dust Cover and Cap Assembly
C470-004R 60 PPI Polyurethane Filter
D470-005R 1.8 GPM Flow Control
EAP470-021 FS-Plus™ Spray Head (assembled)
FAP470-022R Dust Cover and Cap Assembly
G470-024R 60 PPI Polyurethane Filter
H470-025R 3.2 GPM Flow Control
IMPORTANT
In order to operate properly,
the flow control must be
inserted into the body
concave end first.
E
F
G
H
A. SS-1* - Combination eye wash/shower safety station with ABS plastic shower head
(optional stainless steel shower head ”SSH”), stainless steel bowl, powder coated
cast aluminum flag handle and floor flange, 1 ¼” IPS Schedule 40 galvanized pipe
and fittings, 1” IPS and ½” IPS U.S. made chrome plated brass stay open ball valves,
and polished stainless steel pull rod. Unit shall have (2) polypropylene ‘GS Plus’
spray heads with integral “flip-top” dust covers, filters, and 1.8-GPM flow control
orifices mounted on a chrome plated brass eyewash assembly. Unit shall include
ANSI compliant sign.
B. Performance: Unit shall meet or exceed ANSI Z358.1 – 2009, and come with a full 2-
year warranty.
C. Fixture: Guardian Equipment G1902 and G1902SSH
Indice
Altri manuali Guardian Sensore di sicurezza
Guardian
Guardian EyeSafe G1100 Istruzioni per l'installazione e il funzionamento
Guardian
Guardian MK Edge SRL Manuale utente
Guardian
Guardian 01320 Manuale utente
Guardian
Guardian 00235 Manuale utente
Guardian
Guardian Velocity Harness Manuale utente
Guardian
Guardian 04810 Manuale utente
Guardian
Guardian Big Boss HLL Manuale utente
Guardian
Guardian 04630 Manuale utente
Guardian
Guardian 10917 Manuale utente
Guardian
Guardian EyeSafe G1200 Istruzioni per l'installazione e il funzionamento
