Gude Expert net control 2101/2151 Manuale utente

expert net control 2101/2151

21.04.2011

3Table of content

expert net control 2101/2151

Table of content

Chapter 1 Security Advise 5

Chapter 2 Description 5

Chapter 3 Hardware 5

3.1 Content of delivery

3.2 Connections

3.3 Installation

3.4 Status LED

Chapter 4 Configuration 6

4.1 DHCP

4.2 Network settings with GBL_Conf

4.3 Configuration via webinterface

4.3.1 Configuration - Output Ports 8

4.3.2 Configuration - IP address 10

4.3.3 Configuration - IP ACL 11

4.3.4 Configuration - HTTP 11

4.3.5 Configuration - Messages 12

4.3.6 Configuration - SNMP 13

4.3.7 Configuration - SNMP Trap Receiver List 14

4.3.8 Configuration - Syslog 15

4.3.9 Configuration - E-Mail 15

Chapter 5 Operation 16

5.1 Switching at the device

5.2 Switching by Webinterface

5.2.1 Switching 17

5.2.2 Batchmode 17

5.2.3 Control Panel 18

5.3 Sensor

Chapter 6 Features 19

6.1 Bootloader mode

6.2 Firmware update

4Table of content

expert net control 2101/2151

6.3 Technical information

6.4 Fabrique settings

Chapter 7 Support 20

Chapter 8 Declarations of conformity 21

expert net control 2101/2151 Security Advise

1 Security Advise

The device must be installed only by qualified personnel according to the following installation and operating instructions.

The manufacturer does not accept responsibility in case of improper use of the device and particularly any use of equipment

that may cause personal injury or material damage.

Check if the power cord, the plug and the socket are in proper condition.

The device can be connected only to 230V AC (50 or 60 Hz) sockets.

Always connect the device to properly grounded power sockets.To connect a Power-over-Ethernet device, use only certified

and CE marked hardware.

The device is intended for indoor use only. Do NOT install them in an area where excessive moisture or heat is present.

Because of safety and approval issues it is not allowed to modify the device without our permission.

Please note the safety advises and manuals of connected devices, too.

The device is NOT a toy. It has to be used or stored out or range of children.

Packaging material is NOT a toy. Plastics has to be stored out of range of children. Please recycle the packaging materials.

In case of further questions, about installation, operation or usage of the device, which are not clear after reading the manual,

please do not hesitate to ask our support team.

2 Description

expert net control 2101/2151 is a handy little device suitable for different kinds of telecontrolling. In- and output ports on the

device allow to monitor upt to two sensors and switch a contact through a TCP/IP network. expert net control 2101/2151

makes it possible to monitor and switch from any computer in the same LAN and from the Internet.

For installation just connect the power and network cables to expert net control 2101/2151.

After the device has received an IP address every client in the same network is able to switch the output and control the

sensors via webinterface. expert net control 2101/2151 offers also features like SNMP and Syslog.

expert net control 2101/2151 comprises of two sensor interfaces and one switching output.

A watchdog function for the output is implemented.

3 Hardware

3.1 Content of delivery

Included in delivery are:

expert net control 2101/2151

3.2 Connections

1) Status LED

expert net control 2101/2151 Hardware

2) LED Output Port

3) Button "select"

4) Button "ok"

5) Ethernet jack (RJ45)

6) Connector for power supply unit

7) Connector for Sensor 2 (RJ45)

8) Connector for Sensor 1 (RJ45)

9) Terminal clamp Output

3.3 Installation

1.) Connect the power supply cable to the of expert net control 2101/2151 and a socket. expert net control 2101/2151

now is booting and shortly after ready for usage.

2.) Plug the Ethernet cable into the ethernet connector (RJ45) of expert net control 2101/2151 and connect it to your

Ethernet.

3.) Connect the clients to the Power Ports of the device.1.) Connect the power supply unit to the power connector at expert

net control 2101/2151 (6) and a power socket. in case you are using the Power over Ethernet device, there is no need to

connect the power supply unit. expert net control 2101/2151 now is booting and shortly after ready for usage.

2.) Plug the Ethernet cable into the ethernet connector (RJ45) of expert net control 2101/2151 and connect it to your

Ethernet.

3.) Connect the terminal clamp of the output to your device, and plug the sensors into the sensor connectors (RJ45).

3.4 Status LED

The Status LED shows different states of the device:

Status LED red: Device is not connected to the ethernet

Status LED orange: Device is connected to the ethernet, TCP/IP settings are not allocated

Status LED green: Device is connected to the ethernet, TCP/IP settings allocated, device is ready to use

Status LED blinks alternately red and green: Device is in Bootloader mode.

4 Configuration

4.1 DHCP

After switch-on expert net control 2101/2151 looks for a DHCP server and requests an available IP address .

Please check the IP address allocated to expert net control 2101/2151 in the DHCP server settings to make sure that the

same address is used at every reboot.

expert net control 2101/2151 Configuration

4.2 Network settings with GBL_Conf

For changing the network properties manually, the program GBL_Conf.exe is required. This tool is available for free on our

website www.gude.info.

Furthermore GBL_Conf.exe enables you to install firmware updates and to reset expert net control 2101/2151 to its factory

settings.

Activate bootloader mode of expert net control 2101/2151 and run GBL_Conf.exe. The program will look automatically for

connected devices and will display their network configuration.

If the displayed IP address accords with the factory settings (192.168.0.2), there is either no DHCP server available in the

network or no free IP address could be allocated.

Enter a free IP address and the according netmask in the entry mask, then save these changes by clicking on Program

Device SaveConfig.

Restart the firmware of expert net control 2101/2151, so that the changes will take effect. Now click on Search in order to

have the new network configuration displayed.

expert net control 2101/2151 Configuration

4.3 Configuration via webinterface

Go to the website of expert net control 2101/2151. Enter the IP address of expert net control 2101/2151 into the address

line of your internet browser:

http://”IP address of expert net control 2101/2151”/

and press LOGIN.

To enter the configuration menu, click on „Configuration“ on the upper left side of the screen.

4.3.1 Configuration - Output Ports

4.3.1.1 Label

A name with a maximum of 15 characters can be entered here for each output.

4.3.1.2 Initialization status

The output’s switching state after a power-on of the device can be defined here (on, off, remember last state).

4.3.1.3 Initialization delay

While this function is enabled, the output will reactive after the stated time, when it got switched off.

4.3.1.4 Repower delay

While this function is enabled, the output will reactive after the stated time, when it got switched off.

4.3.1.5 Watchdog Funktion

While using the watchdog, electrical devices can be observed. The watchdog sends ICMP-pings or TCP-pings to the device.

If these pings were not answered, during a defined delay (time or pings), the power port will reset. The watchdog function

allows to restart e.g. crashed servers or NAS systems.

You can check the watchdog function and other imformation inside of the switching menu. There are different colors:

expert net control 2101/2151 Configuration

Green text: Watchdog is active and receives ping replies

Orange text: Watchdog is activating at the moment, waiting for first ping reply

Red text: Watchdog is active and does not receive ping replies any longer

When watchdog is activating it waits of a first ping reply. During this time, the information is written as an orange text. After

the receive of the first ping reply, it switches to active, written in green letters.

When a watchdog reset a power port, the watchdog again waits for a first ping reply, as stated above.

4.3.1.5.1 Enable Watchdog

Here you can activate the watchdog for this output.

4.3.1.5.2 Watchdog type

Here you can switch between ICMP ping or TCP ping.

4.3.1.5.3 Host IP

Here you can enter the IP address this watchdog should observe.

4.3.1.5.4 TCP Port

If TCP pings are used, here you can enter the TCP port. A TCP port is not needed, when ICMP pings are choosen.

4.3.1.5.5 Ping interval

Here you can enter the time between two pings.

4.3.1.5.6 Ping retry

Here you can enter how often the ping should be repeated, before a power port reset will be done.

expert net control 2101/2151 Configuration

4.3.2 Configuration - IP address

4.3.2.1 Hostname

Enter the host name of expert net control 2101/2151. expert net control 2101/2151 uses this name to connect with DHCP

server.

Special signs may destabilize your network.