2
GVI Securit
Safety Warning
Retain and follow all safety and operating instructions. Observe all warnings on products. Unplug the product
from the electrical outlet and discontinue use if the following conditions exist: The power cord or plug is
damaged; the product is exposed to liquid; the product is dropped or an object falls on the product; the
product is noticeably overheated. Read this manual carefully before installing the unit. Please read this manual
first for correct installation and operation.
Never install the device on a ceiling that cannot hold its weight. The product may fall down and cause
damages. Never install or use the device in areas exposed to water, oil, or gas. The water, oil, or gas may
result in operation failure, electric shock, or fire. Do not use this unit near water (e.g., near a bath tub, wash
bowl, kitchen sink, laundry tub, wet basement, swimming pool, unprotected outdoor installation, or any area
which is classified as a wet location). Never face the device toward the sun. Direct sunlight may cause fatal
damage to sensors and internal circuits. Touching a wet power cord with hands or touching the power cord
with wet hands may result in electric shock.
Do not service any product yourself. Opening or removing covers that are marked with warning symbols or
labels may expose you to electric shock. Service needed on components inside these compartments should be
done by an authorized service provider. Replace any batteries with the equivalent battery type. Failure to do
so may cause damage or bodily injury. There is a danger of explosion if batteries are incorrectly replaced.
Dispose of all used batteries according to the manufacturer’s instructions.
Install the system in an environment where the ambient temperature does not exceed the maximum rated
ambient temperature of the rack mount system. Ensure there are no obstructions to the case ventilation.
Blocking any of the built-in airflow may cause overheating. The product must be connected to a circuit with an
adequate rating to prevent an over-current condition on the circuit. Slots in the product are provided for
ventilation and should never be blocked or covered since these protect it from overheating. The openings
should never be blocked by placing the product on a flexible surface. The product should not be placed in a
built-in apparatus unless the apparatus has been designed to accommodate the product, proper ventilation is
provided for the product, and the product instructions have been followed.
Operate the product only from the type of power source indicated on the product’s electrical ratings label. If
you have questions about the type of power source to use, contact your authorized service provider. The
power outlet for the power cord should be easily accessible and located as close to the equipment operator
as possible. When you need to disconnect power to the equipment, unplug the power cord from the electrical
outlet. When disconnecting a power cord/cable from an outlet, pull on the connector. Never pull on the cable
itself to disconnect from the power source. Handle all equipment with care when disconnecting from the
product or the power source. Equipment may be hot. The power cord must be properly rated for the
product and for the voltage/current marked on the product’s electrical ratings label. The voltage/current rating
of the cord should be greater than the voltage/current rating marked on the product. Do not overload an
electrical outlet, power strip, or convenience receptacle. Use care when moving products to other countries
with different voltage standards. Substitution for the power supply may result in destruction of the product or
personal injury.
Unplug the product from the wall outlet prior to cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning. Never insert a foreign object into the product’s openings or ventilation slots. The
product should be placed away from radiators, heat registers, stoves, or other pieces of equipment (including
amplifiers) that produce heat. Allow sufficient air circulation around the product and power supply during use
to ensure adequate cooling of the device. Prevent direct exposure to radiant heat sources. Contact the
provider if replacement parts are required. Use only the parts, upgrades, and options sent or obtained from
the provider.
© 2011 GVI Security
v3.04.11
All rights reserved. GVI Security makes no warranty of any kind with regard to this material, including but not limited to the
documentation, function, and performance of these programs and their suitability for any purpose. This document contains
proprietary information, which is protected by copyright. This product specification and manual is also available in pdf format at
www.gviss.com. This information is subject to change without notice.
