GVS H Series Manuale utente
1 2
H Series Access Control Card Reader User Manual_V1.0
Function Overview
Based on the TCP/IP transmission protocol, Access Control Card Reader is one of the main
device of the digital building intercom system. It supports unlock with both IC and ID card.
Functions and Characteristics
Support 24V non-standard PoE power supply or independent 24V power supply
Support exit button and tamper alarm
Support door status detection and timeout alarm
Support IC and ID card
Adjustable unlock time
Support max 10,000 resident cards
Support disconnection alarm
Product Dimension and Specification Parameters
Product Appearance
Interface Description:
①+24V, GND: power input; NO: normally-open; COM: common, NC: normally-closed;
②UNLOCK, GND: external button unlock; GS IN, GND: door status;
③RJ45 network interface: support 24V non-standard PoE power supply
H-CR02
Working Voltage: DC 24V
Static Current: ≤ 60 mA
Working Current: ≤ 100 mA
Dimension(L×W×D):130×80×26 mm
Environment Temperature: -20℃ ～ +55℃
①
②
③
3 4
Configuration
With the custom order function of GVS Configuration Tool, user can configure the device as
Unit or Network card reader, meanwhile Building No., Unit No., Device No. and unlock time
(1~30S) is adjustable with this tool.
Settings are as below:
1. Set a 10 segment IP address, subnet mask:255.0.0.0, then open the software and select
the current IP address as Local IP.
2. Type “H-GVS” or “ALL” in Check Code, click Search button, and the card reader will be
shown in the device name with prefix “CR”. Choose the card reader and click connect button,
then all the following settings can be done with “custom order” option.
ID configuration
While using as Unit card reader, choose “ID(xx-xx-xx):” and input the Building No., Unit No.
and Device No. behind it. For example: to set as building No.1, unit No.2 and device No.3,
type “1-2-3” behind “ID(xx-xx-xx)”, then click execute.
While using as Network card reader, choose “ID(01-32):” and input the Device No. behind it,
then click execute.
Unlock time setting
Select “Unlock timer(01~30s):”, and input new unlock time behind it, range: 1~30s, then click
execute button.
Card reader type setting
Select “Type(1-Unit 2-Network):”, type “1” for Unit card reader, “2” for Network card reader,
then click execute button.
Elevator control setting
Select “Floor NO.(-8~64):”, type the floor number behind it, range:-8~64, and click execute
button.
Note: After configuring the ID number or device type, the IP address of the device will change,
so it is needed to search and connect the device again for further configuration.
Unlock
1) Unlock By Swiping Card
Swipe the IC or ID card to the card reading area to unlock the door, cards need to be
registered by PC Management Center in advance, and one "BEEP" means door opened
successfully, two "BEEP" means card is not registered.
3) Unlock By External Button
There is an interface for connecting with the external button, and the resident can unlock the
door by pressing the external button
5 6
Unlock Time
The default unlock time is 5S, which can be set by the GVS configuration tool, and the range
is 1-30S.
Door status detection and timeout alarm
When the door is unlocked over 120S, the device will ring the alarm, and the alarm message
will be reported to the guard unit or PC Manager Center; the alarm stops until the door is
closed.
Restore factory settings
Factory reset can be done using the GVS configuration tool.
Note: Restoring the factory settings will clear all the registered cards.
Installation
Caution
1. Please stay away from strong magnetic fields, high temperature and humidity, etc.
2. DO NOT drop the device on the ground or subject it to strong impact.
3. DO NOT wipe the device with a wet cloth or with volatile reagents.
4. DO NOT disassemble the device by yourself.
5. DO NOT expose copper to the terminals to prevent electric shock.
6. The power input and output terminals must not be connected in reverse.
7. Please pay attention to the rain or water.
Step 1:
Take out the card reader from
the box and separate the front
and back covers.
Step 2:
Fix the back cover to the
mounting box, and fasten the
hole in the mounting box with
the KM4 screws. Then
connect the cables and thread
it through the hole in the
middle of the back cover.
Step 3:
Fasten the front cover buckle to the back cover buckle as shown in the
picture to fix the front and back cover, and then tighten the KM3 screw into
the bottom of the front cover.
Altri manuali per H Series
10
Questo manuale è adatto per i seguenti modelli
1
Altri manuali GVS Controllori di accesso IP
