GW Instek ASR-002 Manuale utente

Three Phase Power Controller

ASR-002

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS .................................................. 4

GETTING STARTED.......................................................... 7

ASR-002 Overview ...................................................7

Front Panel ..............................................................8

Rear Panel ............................................................. 10

OPERATION .................................................................. 12

Basic Operation..................................................... 13

Advance Setting..................................................... 15

Phase Angle Setting............................................... 17

Voltage Ramp Setting ............................................ 18

Frequency Sweep Setting ....................................... 19

Unit Setting Value Display ..................................... 20

Wire Connection & Accessories ............................. 23

APPENDIX ..................................................................... 25

ASR-002 Dimension ............................................... 25

Using the Rack Mount Kit ...................................... 26

Command List ....................................................... 28

ASR-002 Error Messages........................................ 29

ASR-002 Series User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to ensure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the ASR-002 or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

SAFETY INSTRUCTIONS

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the ASR-002.

Avoid severe impact or rough handling that leads to

damaging the ASR-002.

Do not discharge static electricity to the ASR-002.

Use only mating connectors, not bare wires, for the

terminals.

Do not block the cooling fan opening.

Do not disassemble the ASR-002 unless you are qualified.

If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment

may be impaired.

Power

Supply

WARNING

AC Input voltage range:

230 ~ 240 Vac

Frequency: 50/60 Hz

To avoid electrical shock connect the protective grounding

conductor of the AC power cord to an earth ground.

Cleaning the

ASR-002

Disconnect permanently connected power input before

cleaning.

Use a soft cloth dampened in a solution of mild detergent

and water. Do not spray any liquid.

Do not use chemicals containing harsh material such as

benzene, toluene, xylene, and acetone.

ASR-002 Series User Manual

Operation

Environment

Location: Indoor, no direct sunlight, dust free, almost non-

conductive pollution (Note below)

Relative Humidity: 20%~ 80%, no condensation

Altitude: < 2000m

Temperature: 0°C to 40°C

Storage

environment

Location: Indoor

Temperature: -10°C to 70°C

Relative Humidity: ≤90%, no condensation

Disposal

Do not dispose this instrument as unsorted municipal waste.

Please use a separate collection facility or contact the supplier

from which this instrument was purchased. Please make sure

discarded electrical waste is properly recycled to reduce

environmental impact.

Certification of Compliance

----------------------------------------------------------------------------------

The product is in conformity with the directive: EN 61010-1 /

EN 61326-1 / WEEE / RoHS

GETTING STARTED

This chapter describes the ASR-002 power

controller in a nutshell, including its main

features and front/rear panel introduction.

ASR-002 Overview ..............................................................7

Front Panel .........................................................................8

Rear Panel ........................................................................ 10

ASR-002 Overview

ASR-002, which is a three-phase power controller, is able to controll

up to 3 single phase power supply units (ASR series only).

It effectively makes AC output conformed to 1P3W/3P4W that

generally unit requires, and also turns output into 3P3W via

designated wire method.

When the select single phase power is greater than the capacity of

2kVA, it is suggested that output should be connected to external

terminal for safety consideration.

ASR-002 Series User Manual

Front Panel

Section

Figure

Description

Header Displays

FREQUENCY: It displays frequency.

VOLTAGE: It displays voltage.

MULTIMETER: It displays A current /

W power / PF power factor.

Function Keys

It changes header display A W 

PF.

ON: Output on.

OFF: Output off.

Note

It can be operated when connected to ASR series only.

GETTING STARTED

V Set: It configures voltage.

Range: It toggles between 100V and 200V.

Auto: It enters Auto range by long press.

F Set: It configures frequency.

P Set: It configures L2 / L3 phase.

L1 / L2/ L3: It changes among L1 

L2 L3.

Mode: It toggles between 1P3W3P4W.

Func: It configures advance setting by

long press.

Local: It cancels connection and

enters the local opeation mode.

Knob Key: It adjusts value by scroll.

Also, it switches input adjustion

position by press.

Display Icons

It indicates remote control mode.

It indicates that error of control occurs.

It indicates output phase.

It indicates output mode.

It indicates output range.

It indicates measurement unit display.

ASR-002 Series User Manual

Rear Panel

Section

Figure

Description

USB Port

USB B-type port for remote control.

RS232C Port

RS232C port for remote control.

SIG OUT

SIG OUT for phase control signal

output.

Phase Terminal

The phase terminals for L1/L2/L3.

Warning: Input Voltage 400VAC Max.

Altri manuali per ASR-002

Indice

Altri manuali GW Instek Controllori

GW Instek

GW Instek ASR-002 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente