H-KING FLYCAT Manuale utente
H-KING
FLYCAT
1042mm PARKJET with pre-installed 70mm fan,
motor, ESC and servos
FLYCAT
MANUAL CONTENTS
Description and Specifications -------------------- 2
Using and charging Lipoly batteries ----------- 3
Safety Notes ------------------------------------------------ 4
Assembly ----------------------------------------------- 5 to 16
Center of Gravity ------------------------------------------- 17
Set-Up ---------------------------------------------------------- 18
Flying Tips ---------------------------------------------------- 19
Recommended Accessories -------------------- 20 to 22
Optional Retract Fitting --------------------------- 23 to 24
1
2
The brief was to design a low cost 70mm Parkjet to replace
the popular Flycat, it was to have no frills, look similar and
to have no landing gear. The result is a similar outline to
the original Flycat but it is bigger 1042mm as opposed to
640mm and it has an internal 70mm fan unit rather than an
EDF unit sitting on top. With the addition of fan inlet ducts
and all round streamlining and updated color scheme the
new Flycat looks stunning and it flies as good as it looks.
This version of the Flycat is PNF and comes with a 12
blade 70mm fan unit, high power 3040/2000Kv brushless
motor, 80amp ESC with BEC and 3 9g metal geared
servos. All these items are pre-installed at the factory as
are the colorful decals so time from starting the build to
having it ready to fly is minimal. All you will require is a 4ch
or greater transmitter and receiver and a 6S 30~60C
4000mah lipoly battery with suitable charger.
:Specs:
Wingspan: 1042mm
Fuselage Length: 1115mm
EDF: 70mm 12 blade unit
Motor: 3040/2000Kv brushless
ESC: 80amp with BEC
Servos: 3 x 9g metal geared
Battery: 6S 30~60C 3000mah lipoly (not supplied)
Radio: 4 channels or more (not supplied)
Option: A set of electric retracts can be installed in the Flycat, there
are removable panels to allow for the fitting of these. Please see
notes at the end of the manual.
3
Warnings and Safety notes
Warning on the use of lipoly batteries and
their chargers.
FLYCAT
4
SAFETY INSTRUCTIONS
1. Please read this manual carefully and follow the
instructions before you use this product.
2. This airplane is not a toy, due to it's advanced flying
qualities it is only suitable for pilots with intermediate or
higher experience. If you are a novice then please only
operate with the assistance of an experienced pilot.
3. Not recommended for children under 14 years old.
4. Please set up this plane according to the instructions
and make sure you keep your hands and other parts of
your body out of the way of the rotating propellers at all
times. Failure to do so will result in damage to yourself
and to the airplane.
5. Do not fly in thunderstorms, strong winds or wet
weather.
6. Never fly R/C planes where there are overhead power
lines, automobiles, airports, railway lines or near a
highway.
7. Never fly R/C planes where there are crowds of people
or over organised games. This airplane requires a very flat
landing and take-off area or lake that is clear of tree's and
other obstacles. Remember safety is the responsibility of
the pilot.
8. Do not attempt to catch the plane when you are flying
it.
9. The operator will bear the full responsibility of flying
and the proper operation and usage of this model. We at
Hobbyking will not be responsible for any liability or loss
due to improper use of this model.
5
FLYCAT Kit Components
1. Fuselage
2. Wings
3. Tail Booms
4. Tailplane
5. Fin Servo Connector Cover
6. Wing Retaining Parts and Screws
5
General Assembly
FLYCAT
1. Using slow cure CA or a similar glue apply the glue to the area
of the fuselage where one of the plywood wing retaining tongues
is located.
2. Glue into place the plywood tongue as shown.
6
3. Repeat this process with the other 3 plywood tongues.
,
4. Glue into place the 4 foam in fills on top of the plywood
tongues.
7
FLYCAT
5.This picture shows all 4 foam in fills in place.
6.Apply some slow setting CA or similar glue into the recess on
fuselage side of the tail boom that does not have the cut out in the fin.
8
7.Slide the tail boom over the wing root of the fuselage as shown and
glue into place.
,
8.Prior to gluing the 2nd tail boom into place ensure you
feed the elevator servo extension lead into the cut out slot
in the boom (see following pictures).
Indice
Altri manuali H-KING Giocattolo
H-KING
H-KING Hellcat Little Nugget Manuale utente
H-KING
H-KING Teksumo Manuale utente
H-KING
H-KING Wargo Signature Edge 540T 3D Manuale utente
H-KING
H-KING KI-61 Istruzioni operative
H-KING
H-KING Savage Bobber 1000 mm 5ch ARF Version Manuale utente
H-KING
H-KING FRENZY Manuale utente
H-KING
H-KING F-35 Manuale utente
H-KING
H-KING Cloud Clipper Manuale di istruzioni
H-KING
H-KING Piper J-3 Cub V2.0 Manuale utente
H-KING
H-KING FG-1 Corsair Lucky Gallon Manuale utente
H-KING
H-KING Yak54 Manuale utente
H-KING
H-KING Cessna Skyline Manuale utente
H-KING
H-KING CESSNA TTX Manuale utente
H-KING
H-KING F-16 Manuale utente
H-KING
H-KING HAWKER TEMPEST Manuale utente
H-KING
H-KING Nino Manuale utente
H-KING
H-KING Nori Manuale utente
H-KING
H-KING Seagull Manuale di istruzioni
H-KING
H-KING BIXLER V2 Manuale utente
H-KING
H-KING DH82A TIGER MOTH Manuale di istruzioni
