Hafco HM-51B Manuale utente
INSTRUCTION MANUAL
HM-51B
Turret Milling Machine
(X) 580mm (Y) 190mm (Z) 350mm
M577
Page 1
Instruction Manual for HM-51B (M577)
25/03/2019
- 1 -
DRILLING/MILLING MACHINE
OPERATION MANUAL
Model HM-51B
WARNING
Page 2
Instruction Manual for HM-51B (M577)
25/03/2019
- 2 -
1. Read and understand the entire instuction manual before
operating machine.
2. Always wear approved safety glass/face shield while
using this machine.
3. Make certain the machine is properly grounded.
4. Before operaing the machine,removetie,rings,
Watchesother jewelry,and roll up sleeves above the
elbows.Remove all loose clothing and confine long hair.DO
NOT wear glove.
5. Keep the floor around the machine clean and free of scrap
material,oil and grease.
6. Keep machine guards in place at all times when the
machine is in use.If remove for maintenance purposes ,
use extreme caution and replace the guards immediately.
7. DO NOT over reach.Maintian a balance stance at all timeSo
that you do not fall or lean against blades or
othermoveing parts.
8.Make all machine adjustments or maintenance with the
Machine un-plugged from the power soure.
9.Use the right tool.Don’t force a tool or attachment
to do a job whichit was not designed for..
10.Make certain the motor switch is in the OFF position
Page 3
Instruction Manual for HM-51B (M577)
25/03/2019
- 3 -
Before connecting the machine to the power supply.
11.Keep visitors a safe distance form the work area.
12.Never attempt any operation or adjustment if the
Procedure is not understood.
13.Keep fingers away form revolving parts and cutting
Tools while in operation.
14.Do not attempt to adjust or remove tools during
operation.
15.Always keep cutters sharp.
16.Keep away from the turning handwheel,especially high
speed.
17.Must pour the machine oil into the Gear Box and the power
Feed(optional) rightly.
18.Failure to comply with all of these warning may cause
serious injury.
Page 4
Instruction Manual for HM-51B (M577)
25/03/2019
- 4 -
1. Attention
1.1 Inspection And Acceptance
Please check carefully when open the package and make
sure no parts are missing.
1.2 Safey
Please read the operation manual cafefully before the
installation and adjustment of the machine.when finish the
installation ,check all the details and trial run the
machine idly before put it into operation .
1.3 Caution
Keep in mind the safety measures for electrical and
operating protection.
2. Work Environment
2.1 The elevation of workshop has to be 2000m or less.
2.2 NO conductive dust allowed.
2.3 NO explosive factor allowed.
2.4 NO corrosive gas or steam which may corrode metal
or damage the insulation.
2.5 Keep away from the source of impact or vibration.
3.Operation Instruction
3.1.1 Before starting themachine,read carefully the operation
Page 5
Instruction Manual for HM-51B (M577)
25/03/2019
- 5 -
manual and be fully acquainted with all the details.
3.1.2 The operater should be familiar with all the rules and
points of attention of running and maintaining the machine.
3.1.3Remove all the anti-rust coating or grease from the
machine .
3.1.4 There’s a reliable ground protection the ground wire
must be connected properly before it in operation.
4.Lubrication
Lubricate the sliding and rotating part before trial run.
Pour NO.40 machine oil into the Gear Box and power
Feed(optional).Till indicating through the oil level indicators
then do a overall check.
Keep oil lever above the mark.
Page 6
Instruction Manual for HM-51B (M577)
25/03/2019
- 6 -
I USAGE
The machine is used for cutting metals and nometals.It’s
suitable to drill,and widely use in the field for
instrument,machining,repairing for cutting a single part or a batch
of parts.
II USE AND MAINTENANCE
(Refer to chart 1.)
1.The user must read the Operation Manualcarefully,know
structure and ability of every handle,the system of transmition and
lubrication well.
2.Before operating ,inspect the normal condition Of the column
lock handle,thespindle sleeve and electric equipments.The ground
line must be connect in the ground.
3.When the position of spindle Box to the working table need
to be adjusted,two clamping
shaft① locating on the right side of Hoist Descend sliding
must be lossed firstly,then turn the hoist descend handle in front
of machine , to hoist or descend the working table to the idea
position,finally clamp the clamping shaft②.
4.A micro feeding institute is applied to the machine ,before
using,pls turn the locking bolt③ in right side to form the handle
Page 7
Instruction Manual for HM-51B (M577)
25/03/2019
- 7 -
body with micro gear,then turn the wheel④ in front of the head,
the micro feeding can be realized.
5. The handle body must be seperated from micro gear during
drilling ,when drilling finished , loosen the handle⑤,the sleeve
will reset automatically. The elastic force can be adjusted after
loosing the screw locating in bottom of Spindle Box and turning t h e
spring to different position.The spindle sleeve clamping handle ⑥
should be clamped for milling .To obtain the best effect,pls choose
the 3 blade vertical milling tool,themost,the working table must
be hoisted to the nearest position to the spindle when the 2 blade
milling tool is used.
6.The spindle box that transmitted by the belt can be survived
at 90°(by gear±45°)when operating,pls loose the retaining nut
and pay attention these nuts need only 1 pitch, then swivel screw
lever by socket head screw wrench(S21-24)to make the spindle box
swivel to the place required(clockwise turn the nut,the spindle box
will counter clockwise turn,or otherwise), while turning ,pls pay
attention to the following item:
i:while the spindle box turn from.horizontal position or cloned
position to vertical position,pls help push the upper of spindle
box and gently twitter it.
ii:while the spindle box turn from vertical position to
Page 8
Instruction Manual for HM-51B (M577)
25/03/2019
- 8 -
horizontal position or cloned position,pls push the upper of
spindle box with hand and twitter it gently.
7. The cross—slide of spindle box can be realized through the
ram moving.For cross sliding,pls firstly loosen the two clamping
bolts⑨ locating on the right side of the ram, turn the gear shaft
⑩,to move the ram and spindle box,and tight the two clamping bolts.
8 .The spindle box can turn 360°around the column in the
horizontal plane.To realize this,firstly loosen the 4 pcs of
clamping nuts(11) un-der the ram,turn the ram to the
suitableposition,finally tight the 4 pcs of clamping nuts.
9.The spindle’s turn and revolve can be realized by the switch
loce-ted in the right side of Hoist—descend sliding.
10.The horizontal milling can be realized . The spindle box must
be turn 180°when the tool shaft and jack applied for assistance.
11.If the machine doesn’t work well or have irregular
noise,plsimme-diately shut off machine.
Page 9
Instruction Manual for HM-51B (M577)
25/03/2019
- 9 -
OPERATION MANUAL
No. Ability Model HM-51B
1 Max.drillingdia 30(Iron)
2 Max.end drilling dia 20(Iron)
3 Spindle taper ISO30 / ISO40 / R8
4 Spindle speed number 9（V）
5 Spindle speed range(50Hz) 220-2400
6
Distance between Vertical spindle and
surface of column
250-650
7
Distance between Vertical spindle
and surface of table
70-370
8
9 Vertical spindle travel 120(V)
10 Table size 1000*240
11 Table travel 580*190
12 Motor YL100L1-4 2.2KW(V)
Overall size 1380*1220*2100
13
N.W 850kg
Page 10
Instruction Manual for HM-51B (M577)
25/03/2019
Indice
Altri manuali Hafco Utensili elettrici
