hager EQ45 Manuale utente
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 1 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
Part Description QTY
1Exit Trim Assembly 1
2Screw Pack, 4500 Trim 1
AA Handing Pin 1
BB Screw, 1/4”-20 x 3/4” Pan Head Combo
Drive Machine 4
CC Screw, 1/4”-20 x 1.25” Pan Head
Combo Drive Machine 4
3Power Pack Assy 1
4AA Batteries 4
5Screw Pack, Power Pack, Exit Trim 1
Screw, #12 x 3/4” Pan Head Phillips
Drive Sheet Metal 1
6Main Gasket 1
7Wire Harness, Control to Reader Board 1
8Instruction Sheets 1
9Template 1
8
9
RIM specic Instrucons
Page4
SVR specic Instrucons Page
5-6
Part Description QTY
10 SVR Spacer Block, Power Pack 1
11 6 Wire Extension 1
12 2 Wire Extension 1
13 8 Wire Extension 1
14 Power Pack to SVR Block Screws 1
EE Screws, #12 x 1/2” Thread Forming 4
SVR Block Kit
Required to install battery
pack for SVR exit devices
AA
BBDD
CC
EE
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 2 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
1Safety Information
Carefully read the instructions before installing and using this lock.
WARNING: If the door needs to be drilled, be familiar with how to safely use your tools, and understand all the door preparation steps
before proceeding.
FINISH & CARE NOTES: Either remove the locks or do not install them prior to painting your door to protect the finish. Periodically clean
the locks with mild soap and a soft cloth. Do not use abrasives or harsh chemicals when cleaning or using the lock.
Required Tools
2
T10 PH2 PH3
OPTIONAL OPTIONAL
3Prepare Door
Skip the prep steps if the door has already been prepared.
1
NOTE: Drill from both sides to avoid splintering the finished surface of wood doors. Not all holes are thru.
AA
Mark the Horizontal Centerline and Vertical Centerline on the door face based on the exit device installation instructions.
Align the template and mark the door, drill the holes per template instructions.
4
Remove back plate from Exit Escutcheon
Prepare Exit Escutcheon
1
Hand Escutcheon
• Unstow the wires.
• Remove spring cage if necessary to orient arrows to match downward
motion of the lever. Reattach with screws provided.
• Orient lever to desired handing. RHR shown, LHR opposite side of
escutcheon
• Insert handing pin AA as shown.
2
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 3 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
4
Plug in the Wire Harness #7 into the Reader Board as shown.
Prepare Exit Escutcheon, Continued
3
Close up escutcheon and install Main Gasket.
• Route wires through wiring hole shown
• Install Main Gasket #6
4
7
6
Adjust Telescopic Actuating Shaft for Door Thickness
• The shaft clicks into place and is adjustable to the follow-
ing door thicknesses:
• 1-3/4” [44.5] (As shipped)
• 2” [50.8]
• 2-1/4” [57.2]
• 2-1/2” [63.5]
• 3” [76.2]
5
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 4 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
• Install exit trim onto the exterior side of the door routing the 2 Pin black wire into the
lower wiring hole and the rest of the wires into the upper wiring hole as shown.
• Install the SVR exit device head onto the interior side of the door using the (4) BB
screws (1/4”-20 x 3/4”) provided and route the 2 Pin wire with black shrink wrap
through the hole shown.
BB
1
5Install Exit Trim and Power Pack, RIM
Black
2 Pin
All Other
Wires
Wire
Hole
• Remove the cover of Power Pack #3
• Install Power Pack #3 using (4) DD screws (#12 x 3/4”) provided. Be sure to route the remaining wires through the
lower power pack wiring hole.
2
DD
3
Lower
Wiring
Hole
CONNECT READER AND EXIT DEVICE
• Plug in the Reader (6 pin), 9V power (2 pin), and Exit Trim and Device (8 pin)
wire harnesses as shown above.
• Plug in the 2 Pin plug with the black shrink wrap to the RX wire in the RIM
head as shown below.
3
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 5 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
6
• Install exit trim onto the exterior side of the door routing the 2 Pin black wire into the lower wiring hole and the rest
of the wires into the upper wiring hole as shown.
• Install the SVR exit device head onto the interior side of the door using the (4) BB screws (1/4”-20 x 3/4”) provided
and route the 2 Pin wire with black shrink wrap through the hole shown.
Install Exit Trim and Power Pack, SVR
1
• Plug the 2, 6, and 8 Pin Extension harnesses #11, 12, & 13 into their respective wires in the upper wire bundles.
• Route the extension wires through the lower half of the SVR Spacer Block #10 until about 3” (3.5”?) are sticking
out of the block. Stow the remainder under the block.
• Mount the SVR block #10 to the door using (4) EE screws.
2
BB
Wire
Hole
Black
2 Pin
All Other
Wires
DD
11, 12, 13
10
8 Pin
6 Pin
EE
3
Lower
Wiring
Hole
• Plug in the Reader (6 pin), 9V power (2 pin), and Exit Trim
and Device (8 pin) wire harnesses as shown below.
• Plug in the 2 Pin plug with the black shrink wrap to the RX
wire in the SVR head as shown below.
3
SVR RX
Plugs
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 6 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
7
INSTALL 4 AA BATTERIES
Install the 4 AA batteries in the battery holder. Follow batterie orientation notes in the
holder.
•
What happens when batteries installed? Lights? Sounds
Setup Trim
1
SETUP LOCK
•
Setup procedure
•
2
COMMISSION LOCK
•
GO TO COMMISSIONING PROCEDURE
•
GIVE QR CODE
3
SHOW SELECTION OF OTHER PRODUCTS THAT CAN BE USED
WITH THIS LOCK
HUB
PICTURE
INFO
QR CODE
CYL LOCK
PICTURE
INFO
QR CODE
EXIT DEVICE
PICTURE
INFO
QR CODE
EXTENDER
PICTURE
INFO
QR CODE
READER
PICTURE
INFO
QR CODE
OTHER
PICTURE
INFO
QR CODE
INSTALL COVER
• Install cover, using T10 screw driver
5
EQ45 GRADE 1 EXIT TRIM
INSTALLATION INSTRUCTIONS
I-ED02734
Rev 1, Rev Date: 01/12/2023 [27390110] Page 7 of 8
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment
into an outlet on a circuit different from that to which the receiver is connected, Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to the device not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user's body and
the device.
Cet appareil contient un ou des émetteurs/récepteurs exempts de licence conformes aux normes Innovation, RSS sans licence de
Sciences et Développement économique Canada. Le fonctionnement est soumis à la suivant deux conditions :
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer des
Pour se conformer aux exigences d'exposition RF, une distance de séparation minimale de 20 cm doit être maintenue entre le corps
de l'utilisateur et l'appareil.
Indice
Altri manuali hager Serratura della porta
hager
hager 3400 Series Manuale utente
hager
hager 3221 Manuale utente
hager
hager 3300 Series Manuale utente
hager
hager 47PN Manuale utente
hager
hager 3500 Series Manuale utente
hager
hager 2958 Delayed Egress MagLock Manuale utente
hager
hager 46CE Manuale utente
hager
hager 34K1 series Manuale utente
hager
hager 4500 Series Manuale utente
hager
hager 4200 Manuale utente
