Hakki Pilke Raven 33 Manuale utente
1
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
Hakki Pilke
Raven 33
FIREWOOD PROCESSOR
–Instructions for assembly, operation and maintenance
–EC Declaration of Conformity
–Safety instructions
–Guarantee terms
Valimotie 1, FI-85800 Haapajärvi, FINLAND
Tel. +358 8 772 7300, Fax +358 8 772 732
ENGLISH
THE OPERATOR MUST READ AND UNDERSTAND THESE INSTRUCTIONS
BEFORE OPERATING THE FIREWOOD PROCESSOR.
2
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
Table of contents
1 General information ...................................................................................................................................4
Introduction..................................................................................................................................................41.1
Purpose of use ..............................................................................................................................................41.2
Machine models and basic information .......................................................................................................41.3
Operating conditions ....................................................................................................................................51.4
Safety instructions ........................................................................................................................................51.5
Noise and vibration.......................................................................................................................................51.6
Warning symbols ..........................................................................................................................................61.7
2 Setting up the machine for operation and transport .................................................................................8
Delivery inspection .......................................................................................................................................8
2.1
Main components of the machine ...............................................................................................................82.2
Arranging the machine for operation and transport....................................................................................92.3
Connecting the machine to a power source...............................................................................................132.4
Lifting and moving the machine .................................................................................................................152.5
Additional hydraulic connections (accessory) ............................................................................................162.6
3 Operating the machine............................................................................................................................ 18
machine controls and functions .................................................................................................................183.1
Performing a test run on the machine .......................................................................................................193.2
Wood feeding, cutting and splitting ...........................................................................................................203.3
Using the out-feed conveyor ......................................................................................................................213.4
After use .....................................................................................................................................................243.5
4 Maintenance and adjustment of the machine........................................................................................ 24
Disconnecting the machine from its power source....................................................................................244.1
Adjusting the log length..............................................................................................................................254.2
Height adjustment of the splitting blade....................................................................................................264.3
Replacing the splitting blade ......................................................................................................................274.4
Cutting blade and drive end .......................................................................................................................274.5
Changing the oil..........................................................................................................................................304.6
Changing the oil of the multiplier gear.......................................................................................................314.7
Conveyor maintenance...............................................................................................................................314.8
Lubrication..................................................................................................................................................334.9
pressure regulating valves..........................................................................................................................374.10
Washing and cleaning.................................................................................................................................384.11
Storage........................................................................................................................................................384.12
Maintenance table......................................................................................................................................384.13
3
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
5 Failures and remedial measures.............................................................................................................. 39
Jamming of the cutting blade .....................................................................................................................405.1
Jamming of the wood on the splitting blade..............................................................................................405.2
6 Guarantee terms and declaration of conformity .................................................................................... 41
EC Declaration of Conformity for the machine ............................................................................................... 42
4
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
1 General information
INTRODUCTION1.1
The purpose of this manual is to ensure that the machine is used in the manner intended by the manufacturer,
taking safety into consideration. Everyone operating the machine or working in close proximity to it must study
this manual carefully.
Operators of the machine are expected to have basic skills in tractor handling, such as utilising the cardan shaft
drive and the tractor's lifting equipment. Before commencing work, operators must also familiarise themselves
with the machine's control and safety equipment, and ensure their proper operation.
Additional information on Maaselän Kone Oy’s products is available on our website at www.hakkipilke.fi.
Keep this manual in the immediate vicinity of the machine.
PURPOSE OF USE1.2
The Hakki Pilke Raven 33 firewood processor is designed for preparing firewood from pruned wood or logs. The
firewood processor must not be used to process any treated wood, such as is found in construction waste. Sand,
nails or other impurities in the wood may damage the machine.
The maximum diameter of the logs to be processed is 33 cm. This limit must not be exceeded. When estimating
the diameter of the log you are about to cut, note that the shape of the log and other factors, such as branches
and burrs, make the actual diameter larger, and may prevent the log from being fed to the machine. The machine
is intended to be used mainly for logs less than 30 cm in diameter. However, logs with a diameter of up to 33 cm
can be split temporarily by lowering the splitting blade to the lower position. Do not split logs that exceed 50 cm
in length.
MACHINE MODELS AND BASIC INFORMATION1.3
Model
PTO
Electrical
Driving power
Tractor’s cardan shaft
(PTO)
Electric motor
Weight
730 kg
750 kg
TR/Electrical drive
min 20 hp / max 410 rpm
7.5 kW (min 20 A type C fuse)
Height/width/length
in transport position
Transport position 251/136/262 (cm)
In-feed/out-feed conveyor
220/400 (cm)
Saw bar/chain
bar: 15” groove 1.5 mm chain: 66 loops, pitch 0.325”
Max log diameter
33 cm
Max/min log length
Log max 50 cm; min 17 cm
5
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
The machine’s serial number, date of manufacture, weight, operating voltage (electrically operated machines)
and model are indicated on the grey type plate located on the machine frame below the locking latch of the out-
feed conveyor, on the right side of the operator.
OPERATING CONDITIONS1.4
The temperature range within which the machine can be operated is -20 to +30°C. In the winter, the operator
must ensure that there is no risk of slipping in the working area.
The working area must be level and clear of unnecessary items. No unauthorised persons are allowed to
enter the working area. The machine may only be used in sufficient lighting conditions. These require-
ments must be met for the entire duration of the work.
The machine may not be used indoors.
SAFETY INSTRUCTIONS1.5
This device is intended to be operated by only one operator. The danger zone is 10 m from the machine.
Persons under 18 years of age may not operate the machine.
The operator must ensure that the use of the device does not cause danger to others and that there are
no unauthorised persons in the danger zone.
The machine must not be operated while under the influence of alcohol or other drugs, or when tired.
The machine must not be operated unless the operator has familiarised themselves with this instruction
manual.
The machine has been designed solely for making firewood.
The machine must be placed in the transport position whenever it is moved. When transporting the ma-
chine on a public road, it must be equipped with additional lights.
The operator is not permitted to modify the structure or operation of the machine or remove protective
equipment.
The operator must wear ear protectors, sufficiently tight-fitting work clothing and gloves, protective gog-
gles and safety footwear.
Before starting up the machine, the operator must ensure that the machine and its guards are intact.
When powering the machine with a tractor, the operator must ensure that the cardan shaft is undam-
aged and that the selected rpm range is correct. The machine must be attached to the tractor's lifting
equipment during operation.
Before starting up the firewood processor, the operator must ensure that all the control and safety devic-
es are functional.
When cleaning the machine or carrying out any maintenance, it must be disconnected from its power
source.
Note! Do not leave a running machine unsupervised!
NOISE AND VIBRATION1.6
A-weighted maximum sound pressure at the working location is 94 dB (LpASmax) and the sound power level
during the work cycle is 105.0 dB (LWA). The vibration values do not exceed 2.5 m/s2.
6
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
WARNING SYMBOLS1.7
READ THE MACHINE’S MANUAL
BEFORE OPERATING THE MA-
CHINE.
WEAR EYE AND EAR PROTECTION.
WEAR SAFETY FOOTWEAR AND
WORK GLOVES.
DO NOT WEAR ANY LOOSE
ITEMS OF CLOTHING.
ALWAYS GRAB THE PIECE OF
WOOD OR LOG FROM THE SIDE.
LIFTING POINT FOR FORKLIFT.
BEWARE OF MOVING PARTS.
BEWARE OF THE CARDAN SHAFT.
BEWARE OF THE CHAIN.
BEWARE OF THE BLADE.
ONLY ONE PERSON MAY OPERATE
THE MACHINE.
DISCONNECT THE POWER SUP-
PLY BEFORE CARRYING OUT
MAINTENANCE PROCEDURES.
THE DANGER ZONE IS 10 M
RISK OF CRUSHING
7
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
FROM THE MACHINE.
THE MAXIMUM PERMITTED
ANGLE OF THE CONVEYOR IS
40°. DO NOT PASS UNDER THE
CONVEYOR.
THE MAXIMUM SPEED FOR THE
CARDAN SHAFT IS 410 RPM.
THE ROTATION DIRECTION IS IN
THE DIRECTION OF THE ARROW.
HYDRAULIC OIL
SAW CHAIN OIL
DANGER ZONE
LUBRICATION POINT
8
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
2 Setting up the machine for operation and transport
DELIVERY INSPECTION2.1
Dispose of the machine’s packaging material in an environmentally friendly manner.
Check that the machine has not sustained any damage during transport, and ensure that all necessary parts are
included in the package. In the event of any defects or damage, contact the retailer immediately.
MAIN COMPONENTS OF THE MACHINE2.2
The main components of the Hakki Pilke Raven 33 firewood processor are presented in the figure below.
A. In-feed conveyor
B. Control unit
C. Cutting and
splitting unit
D. Out-feed conveyor
Figure 1. Main components of the machine
9
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
ARRANGING THE MACHINE FOR OPERATION AND TRANSPORT2.3
Before arranging the machine for operation, ensure that the operating conditions detailed in Section 1.4 are met
and review the safety instructions in Section 1.5.
Note! Inspect and clean the machine before setting it up for transport!
Placing the out-feed conveyor in the operating or transport position
Figure 2.
Figure 3.
10
HAKKI PILKE RAVEN 33 TRANSLATION VERSION 1
Place the in-feed conveyor in the operating position as follows:
1. Ensure that sufficient room is available to lower the in-feed conveyor (approx. 2 m).
2. Remove the other end of the support leg holder C from the lug (Figure 2).
3. Release the lock by removing pin A and turning locking latch B out of its slot (Figure 3).
Note! At the same time, hold the end of the in-feed conveyor with your left hand!
Figure 4.
4. Lower the in-feed conveyor with your left hand while simultaneously using your right hand to guide support leg
D into slot E (Figure 4).
When placing the in-feed conveyor in the transport position, lift the conveyor to the upper position, turn
locking latch B into its slot and insert pin A (Figure 3). Use holder C to lock the support leg in place (Figure
2).
Indice
Altri manuali Hakki Pilke Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
