HAKO 7092.65 Manuale utente
Assembly Manual
LED working light (7092.65)
2
Foreword
The installation procedures described
in this assembly manual should only be
undertaken by a Hako service centre or
a workshop authorised by Hako. Mem-
bers of staff with the required level of
training and expertise are only guaran-
teed in the said workshops.
This assembly manual may be used
only in conjunction with the instruction
manual of the machine.
Safety instructions
Please observe the general safety reg-
ulations of the corresponding machine
in the relevant operating manual.
Place the machine on a level surface
and secure it with the parking brake.
Switch the machine off and pull out the
key.
We would expressly advise you that no
legal claims may be asserted based on
the contents of this manual. In the case
of necessary repair work, please make
sure that only original spare parts are
used. Only original spare parts guaran-
tee constant and reliable operational
readiness of your machine. We reserve
the right to make changes in the inter-
ests of further technical development.
Valid as from: September 2017
Hako GmbH
23843 Bad Oldesloe, Germany
Hamburger Str. 209-239
Phone +49 4531 806-0
Introduction
4
LED working light
1.3 Installing the working light
The working light is installed on the left
next to the front wheel (Fig. 2/1).
1. Fit working light to holder of chassis
(Fig. 2/2).
2. Insert corrugated hose holder into
existing hole (Fig. 2/3).
3. Secure cable of working light to cor-
rugated hose holder in such a way
that it is free of tension.
4. Lead cable through floor opening
into the interior (Fig. 2/4).
5. Connect plug of working light to
2-pin connector E01 of cable
loom W 3 (Fig. 2/5).
1.4 Adjusting the working light
Align working light so that it is straight-
ahead in the direction of travel.
Set tilt angle to approx 5° (Fig. 2/6).
Fig. 2
4
1
2
3
5
6
5°
5
LED working light
1.5 Setting in the configuration
menu
The LED working light option must be
activated via the configuration menu.
Requirements:
• Batteries inserted
• 4-digit code or diagnosis plug
97097737 is present.
If diagnosis plug is used:
Connect diagnosis plug to slot X20 of
controller A1 (Fig. 4/1).
Setting:
1. Turn on the machine.
2. Select the arrow softkey (Fig. 3/3) on
the control panel using the turn-push
knob (DDS) (Fig. 3/2) and press to
access the sub-menu.
3. Select the configuration menu in the
sub-menu (Fig. 3/4).
Fig. 3
4. Enter the 4-digit code in the configu-
ration menu at the top (Fig. 3/5):
- Rotate the DDS until the required
field is reached.
- Press DDS, then rotate to adjust
the value.
- Press again to save the value.
Alternatively, use the diagnosis plug!
5. Select the value of the option under
(Fig. 3/6) in the configuration menu
and save by pressing the DDS. After
confirmation of the final digit, OK?
appears. Press the DDS again to
save the value. The saved value is
now displayed in green.
If the value is not to be saved, exit
the menu using the return button
(Fig. 3/7).
Option Value
LED working light 1. 6. 1.
2
1
3
4
5
6
7
Advanced Technology for a Cleaner,
Better Environment
Hako GmbH ·Head Office · Hamburger Str. 209-239 ·23843 Bad Oldesloe ·Germany
Phone +49 4531 806-0 ·Fax +49 4531 806-338
88-10-3150 - 3925-00
Altri manuali HAKO Luce da lavoro
