Hallmark HM46 Manuale utente

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 1 of 13

Hallmark Series Owner’s Manual

HM 46 and HM 57

With Saunalogic Control

and Bluetooth Sound System

Read Before Installation……………………………………………………...... 2

Precautions Before Use………………………………………………………... 2

Room Assembly……………………………………………………………….. 3

Bench / Interior Assembly……………………………………………………... 6

Electrical / Heater Assembly…………………………………………………… 8

SaunaLogic Control Operations………………………………………………… 10

Bluetooth Sound System Operation……………………………………………. 11

User Maintenance Instructions………………………………………………… 12

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 2 of 13

READ BEFORE INSTALLATION

Read all instructions carefully before installation including instructions

packaged separately with the sauna heater. Please leave all instructions and

warranty with the owner.

WARNING: When using electrical sauna heaters and associated sauna products, basic

precautions must be followed, including the following:

1. Grounding is required.

NOTE: A GFCI (Ground Fault Interrupt Circuit) device is not required by ETL. A

GFCI may be installed if required by local codes but will nuisance trip during use of

the product. - CAUTION: Loose wire connections can cause heat damage to wires,

terminal blocks and other components and may void the warranty.

2. No electrical receptacle shall be installed in the sauna room.

3. Do not tamper with the door or install a latching or locking system. Malfunction of

which may cause entrapment inside the heated room.

4. Do not block ventilation openings. Vents must be kept free of obstruction so proper

airflow is maintained in the sauna room. Do not stack anything in front of the vents or

push the back of the room up tight to a wall surface.

PRECAUTIONS BEFORE USE

WARNING: Prolonged exposure to elevated temperatures is capable of inducing

hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches several

degrees above the normal body temperature of 98.6°F. The symptoms of hyperthermia include

an increase in the normal temperature of the body, dizziness, lethargy, drowsiness, and fainting.

The effects of the hyperthermia include failure to perceive heat, unawareness of impending

hazard, fetal damage in pregnant women, physical inability to exit the room and

unconsciousness.

WARNING: The use of alcohol, drugs, or medication is capable of greatly increasing the risk

of fatal hyperthermia.

CAUTION FIRE HAZARD: Do not use the sauna room for drying clothes, bathing suits,

etc. Do not hang towels above the heater or place any object, other than the rocks supplied, in the

heater. If any darkening of the wall around the heater is noticed, discontinue sauna use

immediately.

HARDWARE INCLUDED

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 3 of 13

ROOM ASSEMBLY

The sauna rooms come in different sizes. These instructions are only for the 4x6 and 5x7

Hallmark Series rooms.

* Each panel is heavy. Be careful to avoid injury when installing, especially the top panel(s).

* Two adults are required for the installation of sauna room.

* There is a “+” button or a “–” button at the sides of each panel, which will be installed

correspondently with one “+” to one “–” in following way when installing: The panel with “+”

button should be lifted up about 1 inches (2.5cm) higher than the panel with the “-”button (Refer

to Picture 1); place the “+” panel against the panel with “–” button (Refer to Picture 2), and then

slide down the panel with “+” button until the two panels are equal in height (Refer to Picture 3).

If they are not equal in height or there is an obvious gap between the two panels, that means they

are not properly attached, and you should try again.

Typical room installation is as follows:

1. Place floor/base panel on level surface. If not even, shim the base panel until level

2. Place back right wall panel on floor/base panel

3. Place right wall panel on floor/base panel then interlock to back panel

4. Place left back wall panel on floor/base panel and interlock to right back panel

5. Place left wall panel on floor/base panel and interlock to back left panel

6. Place right front wall panel on floor/base panel and interlock with right side wall

7. Place ceiling on top of all wall panels

8. Install glass window and door.

Note: The vents must be kept free from any obstruction so proper airflow is maintained in the

sauna room. Do not stack anything in front of the vents or push the room wall with vents up tight

to a wall surface.

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 4 of 13

ROOM ASSEMBLY (CONT.)

Step 1: Place the floor panel in the desired

location on a level surface.

Note: The floor panel must be level before

installing the wall and ceiling panels. If the

surface is not level, you may need to shim the

floor/base panel to get level.

Step 2: Place the back panel and interlock the side

panels on to the back panel.

Step 3: Place the front panel on the room.

Step 4: Place the ceiling panel on the wall panels.

Note: Make sure the top panel’s front is facing the

front, that the trim of the top panel fits completely

around the walls and that the connection wires

fron the control panel wall protrude through the

hole of the ceiling panel. Be careful to not kink or

pinch the wires.

Step 5: Lift up the ceiling slightly and carefully

place glass section into groove on floor panel and

align with groove in ceiling panel. Lower the

ceiling down to lock the room.

Step 6: Connect the wires in the ceiling panel

accessed via flip-up panel as shown above.

Note: Match each wire connection to the similar

corresponding connector type.

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 5 of 13

Step 7: Remove door handle from brown box and

separate the two pieces by loosening four

setscrews with an Allen wrench.

Step 8: Remove the screw and spacer from the

handle.

Step 9: Install the handle on the glass. Ensure the

plastic gaskets are on both side of the glass while

installing the screw into the door handle.

Note: Place all wood handle inside sauna room.

Step 10: Install exterior portion of door handle on

the screw section and tighten all four setscrews

with Allen wrench.

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 6 of 13

BENCH / INTERIOR ASSEMBLY

Bench supports are already installed in the

proper location for the upper and lower

benches, so no assembly of bench supports is

required.

MODEL HM 46:

The HM 46 bench system has two benches.

Both the upper and lower benches span from the

left wall to the right wall. The wider bench is

the upper bench and the narrower bench is the

lower bench.

MODEL HM 57:

The HM 57 bench system has three (3) benches. (Upper Main Bench, Upper Return bench, and

Lower Main Bench) The upper main bench is installed along the right wall, spanning from the

front wall to back wall. The shorter upper return bench butts up to the main upper bench and

spans to the left side wall. (See photos and instructions below for HM 57 layout).

Step 1: All wall supports are pre-installed.

Double check all panels are tightly secured at

the corners to ensure proper bench

installation.

Step 2: Place the lower bench along the wall

spanning from left wall to right wall.

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 7 of 13

Two screws under the return

bench

Step 3: Place the return bench squarely onto

the pre-installed supports to provide a snug

fit. The bench will be supported by the Upper

bench wall support and the armrest support

by the glass wall.

Step 4: Install the screws under the bench upper

return bench through the frame to the main

upper bench and tighten the nuts.

Step 5: Be sure to fasten the upper benches to

the walls using the 1 1/8” screws provided.

Lower benches are meant to slide on the

lower bench supports for cleaning

convenience. The bench installation is

complete.

Step 6: Install the backrests above the upper

benches according to the predrilled holes, using

the 1 1/8” screws provided.

Note: Be sure to install at the same level to

ensure a well-balanced look..

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 8 of 13

ELECTRICAL / HEATER ASSEMBLY

Step 1: Mount the CB-PK-1 contactor box to the

right wall with 4 screws provided by locating the

lower left corner of the box to wood pencil trim

on wall.

Step 2: Mount the sauna heater according to the

Installation and Operation Manual provided with the

heater. The wall is labeled and predrilled for the top

lag screws from the sauna heater hardware.

Step 3: Connect wires from building electrical

supply to the lower terminal block labeled L1,

L2, and Gnd.

Connect wires from sauna heater to upper

terminal block labeled T1, T2, and Gnd

Step 4: Connect all the quick connections according to

the picture and installation manual into the CB-PK

Box.

1- Radio Power (from wall to terminal block in

box)

2- High Limit (from heater to PCA)

3- Room Temp Sensor (from wall to PCA)

4- Color Therapy Lights (from wall to PCA)

5- Control (from wall to PCA)

6- Interior Lights (from wall to transformer in

box)

Heater Screws

Location

Bottom of heater

guard location

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 9 of 13

Step 5: Connect the sensor wire coming out of

the wall above the heater to the sensor assembly.

The sensor will then be fastened to the wall over

the hole with a screw.

Snap cover on the sensor and be sure to place the

solid white portion of the sensor over the wire

connections.

Step 6 Install the wood heater guard around the sauna

heater using the 1 1/8” screws provided. The heater

guard location is marked on both walls with a label.

Place the bottom of the heater guard to cover the label

on the walls and secure into location.

710-0133 HM 46 57 Hallmark Manual Date: 06/24/16

Rev 04 Page 10 of 13

Saunalogic Control Operation

Operating Instructions for Lighting

Press “Internal Light” to switch on or off.

Press “Color Light” to scroll through the

colors and then off.

Operating Instructions for Heater

Default settings for temperature are preset to 176°F, the bath time is set to 60 minutes and 0 minute delay

to start to heat. These settings are adjustable (as described below) from 125°F to 194°F. Length of sauna

can be set from 0 to 60 minutes. The time delay before start can be up to 23 hour and 59 minutes. Any

changes are remembered by the heater for your next bath. Should the heater power be lost then restored,

the settings will return to their default values. If the heater does not start heating, refer to the Pre-Set

Delayed Start section below.

STARTING SAUNA HEATER IMMEDIATELY

Press the control POWER button once. The room temperature will be displayed on the control. The

heater will turn on and begin heating the room to current set points. Once the set temperature is reached

inside the room, the heater will turn heater on and off again as needed to maintain the desired

temperature. At the end of the selected time (60 minutes maximum), the control will turn itself off and

the control display will turn off.

SETTING THE TIME AND TEMPERATURE

To set the sauna length time, press the control POWER button to turn on the heater. Press the “"+" or "-"

buttons on the left side of control to increase or decrease time for desired setting. The maximum of time is

60 minutes.

To set the temperature, press the control POWER button to turn on the heater. Press the TEMP "+" or "-"

buttons on the right side control to increase or decrease temperature for desired setting. The maximum

temperature is 194°F (90°C).

Note: Typical sauna bathing set-point temperature is 150°F to 165°F on the control.

PRE-SET DELAYED START

With the electricity applied to the CB PK-1 box, press the control POWER button once. The room

temperature will be displayed on the control. Press the “clock” button. Press the "+" or "-" buttons on the

left side of the control to increase or decrease delay time for desired setting. The maximum of time is 23

hours and 59 minutes. If no delay start is desired, set to 00:00 and press “clock” button.

Note: The LED light above clock will glow when system is in the delayed start mode and the “:” will

flash in the time section.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hallmark Prodotto idraulico

Hallmark

Hallmark V3 Series Manuale utente

Manuali Prodotto idraulico popolari di altre marche

Weka

Weka 506.2020.00E Istruzioni operative

Kohler

Kohler K-6228 Istruzioni per il montaggio

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manuale utente

American Standard

American Standard DetectLink 6072121 Manuale utente

Uponor

Uponor Contec TS Manuale utente

Pfister

Pfister Selia 49-SL Manuale utente

Fortis

Fortis VITRINA 6068700 Manuale utente

Fortis

Fortis MILANO 78211JS Manuale utente

Kohler

Kohler K-12183 Istruzioni per il montaggio

Maxxus

Maxxus MX-M206-01 Manuale utente

Moen

Moen 5922 Series Manuale utente

Viega

Viega Prevista Pure 8512 Manuale utente

Kohler

Kohler Centerset K-15240 Istruzioni per il montaggio

Viega

Viega Prevista Dry 8522.33 Manuale utente

Sanela

Sanela Lema SLP 59RB Manuale utente

Elkay

Elkay EDF15AC Manuale di installazione

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manuale

baliv

baliv WT-140 Manuale utente