Hamamatsu C7557 Manuale utente

MCD CONTROLLER

C7557

INSTRUCTION MANUAL

HAMAMATSU

HAMAMATSU PHOTONICS K.K.

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 1-

Contents

Contents ------------------------------------------------------------- 1

SAFETY AND PREPARATION FOR USE ------------------- 3

Chapter 1 Hardware --------------------------------------------------- 5

General --------------------------------------------------- 5

Standard Configuration ------------------------------ 6

Installation --------------------------------------------------- 7

System Outline ---------------------------------------- 8

Nomenclature --------------------------------------------------- 11

Connection --------------------------------------------------- 12

Operation --------------------------------------------------- 13

Timing Chart --------------------------------------------------- 15

Specifications --------------------------------------------------- 20

Outward Appearance ---------------------------------------- 25

Chapter 2 Software Library ---------------------------------------- 26

Software Development---------------------------------------- 27

Initialization --------------------------------------------------- 28

Installation --------------------------------------------------- 29

Checking Connected Devices ------------------------------ 30

MCD Selection--------------------------------------------------- 31

Amp Gain Control ---------------------------------------- 32

A/D Converter Control ----------------------------- 33

Trigger Mode Control ---------------------------------------- 34

Delay Time of External Start Control ------------------- 35

Trigger Polarity Control ------------------------------ 36

PULSE OUT Control ---------------------------------------- 37

Delay Time of PULSE OUT Control ------------------- 38

Pulse Width of PULSE OUT Control ------------------- 39

Polarity of PULSE OUT Control ------------------- 40

Sensor Type Control ---------------------------------------- 41

Number of Pixels Control ------------------------------ 42

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 2-

Number of Summing Pixels Control ------------------- 43

Mode Control --------------------------------------------------- 44

Exposure Time Control ------------------------------ 45

Temperature Control ---------------------------------------- 46

Peltier Power Control ---------------------------------------- 47

Temperature Monitor ---------------------------------------- 48

Measurement and Reading Data ------------------- 49

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 3-

SAFETY AND PREPARATION FOR USE

CAUTION

This instrument may be damaged if it is operated with the LINE VOLTAGE

SELECTION set for the wrong AC line voltage or if the wrong fuse is installed.

LINE VOLTAGE SELECTION

The C7557 is designed with an auto ranging power supply that will operate from an

input power source of 50/60Hz,100-240V AC. It is fused at one point. It is rated at

2.5Amps. The fuse is located in the AC power entry module just below the power

cord connection point on the rear panel. This fuse may be inspected by removing the

power cord from the back plate and then pulling out the small plastic drawer

located immediately below. The drawer should be carefully pried from its indent at

the center using a tool such as a small blade screwdriver. The operating fuse is

located just to its rear.

If the main fuse is open, the Power LED of front panel will not come on when the

switch is in the ON position. If the main fuse is intact, the light will come on when

the switch is in the ON position.

LINE CODE

The C7557 uses a three wire power cord for connection to the power source and to a

protective ground. The exposed metal parts of the instrument are connected to the

outlet ground: to protect against electrical shock, always use an outlet which has a

properly connected product ground. To avoid shock or injury do not remove product

covers or panels. Do not operate the product without all covers and panels in place.

CONNECTION TO OTHER INSTRUMENTS

All rear panel BNC shields are connected to the chassis ground and to the power

outlet ground via the power cord. Do not apply any voltage to either the shields or

to the outputs. The outputs are not protected against connection to any potential

other than ground.

LOCATION

The C7557 is made some holes in the cover to radiate heat. This instrument may be

damaged if it does not radiate heat enough. To avoid blocking the holes, do not locate

any other instruments near by.

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 4-

CLEANING

The C7557 does not need to cleaning.

INSTALLATION LOCATION

To ensure the proper operation of the system, avoid installing it in the following

locations:

(1) in areas near strong electric and/or magnetic field sources

(2) in areas at ambient temperatures below 0℃or above 40℃

(3) in areas subject to large changes in temperature

(4) in areas with high humidity(more than 80%) or damp environments

(5) in areas subject to vibration

(6) in areas with high-density corrosive gases(chlorine, fluorine, etc.)

(7) in areas with excessively dusty environments

(8) in areas exposed to direct sunlight

(9) in areas higher than 2,000 meters above see level

SYMBOLS

The C7557 is marked the symbols below.

“COUTION”. To avoid shock or injury, see the instruction manual.

ON ( POWER SWITCH )

OFF ( POWER SWITCH )

Alternating Current

〜

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 5-

Chapter1 Hardware

General

The C7557 can drive a multichannel photodetector heads as CCD, InGaAs, N-

MOS. It converts the video signal from the sensor to a digital output, which is

then sent to a personal computer via the SCSI interface. The MDDA Software

is available for analysis.

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 6-

Standard configuration

Component

1) C7557 1 piece

2) SCSI terminator 1 piece

3) Fuse ( 2.5A ) 2 pieces ( located in the fuse box )

4) Power cable 1 piece

5) Instruction manual 1 piece

SCSI terminator

TECONTROLI/O

POWER

SIGNALI/O

C7557

Power cable

Fuse

Instruction manual

HAMAMATSU

C7557

Instruction M anual

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 7-

Installation

1. Power requirement

The power supply voltage of the C7557 is AC100V to AC240V

(50/60Hz).

2. Fuses

Inspect the fuse before plugging the power cord of the instrument

into an outlet. The two fuses are located in the fuse box (in the

LINE ) on controller rear panel. The fuse is rated at 2.5A.

When replacing the fuse , use only fuse of the same ratings as those

provided.

[Caution]

Using a fuse of a different rating or bypassing the fuse is dangerous and

not recommended.

3. Ground

Connect the power cord plug to a 3-prong power outlet.

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 8-

System outline

1) A/D conversion part

This part is differential input A/D converter.

12-bit(1MHz) or 16-bit(250KHz) converters are available. Converted

digital data are send to the control part.

Some amp gain is available as x1/2, x1, x2, x5, x10, x20, x50, x100.

2) Control part

This part drives the various multichannel detector heads, controls

temperature of multichannel detector, and controls converted digital

data. This part also has an SCSI interface for communicating with a

personal computer.

3) Power supply part

This part contains a switching power supply and noise filters.

Detailed explanation is on the next page.

HAMAMATSU

MCD CONTROLLER C7557

Chapter1 Hardware

- 9-

System outline

A/D conversion part block diagram

Control part block diagram

12bit

A/D

16bit

A/D

Video Buffer

Buffer

A/D Trig Digital Data

+5V

+15V

-15V

AMP

VIDEO OUT

Buffer

SIGNAL I/O

FIFO Memory SCSI

CPU

DMAC

SCSI I/F

Timer Buffer Start

Buffer Clock

EOSBuffer

Buffer SYNC. OUT

Buffer TRIG. IN

Buffer PULSE OUT

Buffer Mode Select

RS-232C RS-232C I/F

+5V

+15V

-15V

+12V

+24V

+5/6V

Digital Data

10bit

A/D

Cooling Control

TempMonitor

AMP

Buffer TE CONTROL I/O

SIGNAL I/O

Indice

Altri manuali Hamamatsu Controllori

Hamamatsu

Hamamatsu C4742-95-12ER Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente