HappyFabric HappyPress Manuale utente
BEDIENUNGSANLEITUNG
OPERATING MANUAL
April 2019
Thank you
for purchasing a HappyPress.
We hope you will be happy with your new
HappyPress and have even more fun on textile printing and
implementing your designs.
For any questions about your HappyPress, you can
enter the serial number of your HappyPress here.
Register your HappyPress
www.die-happy-press.de
and additionally receive a warranty extension
Happy Fabric
wishes you a lot of fun with your HappyPress.
OPERATING MANUAL
EN - ENGLISH
CONTENTS
Introduction to the Manual 21
Important Safety Instructions 22
Detail Picture 23
Commissioning 24
Control Panel 25
Setting the Temperature and Time 26
Adjusting the pressure 27
Printing / Pressing 28
CE Declaration of Conformity 29
Warranty Terms 30
21
HappyFabric.deHappyFabric HappyFabric.de
INTRODUCTION TO THE MANUAL
Introduction to the Manual
This manual has been designed to be user friendly. Read it carefully, and follow the
step-by-step instructions to get the best possible printing results.
• Work very carefully and avoid contact with the hot plate to avoid serious burns.
Keep hands clear of heat platen while closing the press to prevent bruises and
burns.
• Use your press only on stable, steady and non-slip surfaces.
• Check the press immediately after unpacking for any transport damage. Allow
the press to stand for several hours at room temperature before using to pre-
vent the formation of
condensation, and thus avoid the risk of a possible short circuit.
• Operate the press whilst standing, with both hands on the handle provided for
this purpose. The machine
should stand at a level that is adapted to the height of
the operator.
• The optimum operating condition for your press is at a maximum humidity of 70 %,
and an ambient temperature between +15 °C and +50 °C.
• Should any liquid or solid object get inside the unit, immediately disconnect the
power plug from the wallsocket/outlet, and have the machine checked carefully by
an expert before it is used again.
• No liability is assumed by the manufacturer for any improper or nonintended
use of the machine resulting in property or personal injury.
22
Important Safety Instructions
Before you use your press, you should follow some basic precautions, including the
following:
Read the complete manual before you start to use your press.
Use the press exclusi-
vely for printing textiles, or other suitable products that do not contain heat sensitive
components, and have not been treated with chemical additives.
Keep your press secure from rain, moisture, dirt, dust, direct sunlight, mechanical vibrati-
on or shock, as well as keeping it well away from highly flammable or explosive materials.
Never pull on the power cord to turn off your press, but always use the ON/OFF switch.
If the machine will not be used for long periods of time, pull the plug carefully from the
wall socket.
The power cord must not come into contact with the hot plate (upper platen).
Never use your press with a damaged or defective power cable. In the event of any
damage or defect, never remove the casing of your press, but discuss the problem
with a specialist who may be contacted during normal business hours by telepho-
ning (+49) 030/89 747 348. Opening the case will void the warranty on the press.
Avoid using the press in locations where children, or third parties have unsupervised
access to the press. The minimum distance for children, or other persons should be
at least 1.5 m away from the press to prevent burns and bruises.
When lifting the press for any reason you should grip the machine and not the
casing, as the casing contains plastic and delicate electronic components. Hold the
press at the base plate, or directly on the bottom. The press must be completely
cool and transported in the original box.
Before connecting the power cable check that the operating mains voltage will be
230 V. The outlet must be fused with at least 10 amps. You should only connect one
machine to a mains socket, and not use an extension lead.
When using the machine for printing, it should never be left unattended (danger of
fire). Please take care when loading the machine that it is fully open to avoid any
burns.
Keep these instructions in a safe place.
IMPORTANT SAFETY INSTROUCTIONS
23
HappyFabric.deHappyFabric HappyFabric.de
DETAIL PICTURE
Pressure
Adjustment Knob
Power Supply Fuse 4 A
LED-Display
Lift Handle
Power ON/Off Switch
24
COMMISSIONING
Connecting the Power Cord
Ensure that the operating voltage of the mains supply is 230 V before connecting
the machine. The socket must be secured with at least 10 amps. Only connect one
machine per socket.
Do NOT use extension cords, as this can lead to overheating of the cable (fire ha-
zard), or to a loss of voltage.
Abb. 1 Turning the system on
• Open the press.
• Locate the ON/OFF switch on the back of the housing of your machine
• Turn the switch to ON.
If your HappyPress 3 switches itself off, restart the machine by pressing the power
switch twice to turn it off and back on again. Proceed by closing and opening your press
once before continuing to print.
Note:
If the power cord is damaged, it must be replaced by the Manufacturer or by a techni-
cal member of staff, to avoid the risk of an electric shock. Use a HSJ Power Cord with
250V - 10AMP for replacement.
interrupting the power supply. Push the button until it locks to reconnect the power
supply.
Safety Switch/Fuse
The number on the safety switch indica-
tes the amp at which the safety switch
will release. During a power overload, the
switch will „pop out“,
Warning:
Failure to observe this information may result in erratic controller func-
tions, inaccurate displays and slow heat-up, the circuit breaker disengaging
Please consider this when replacing.
1
2
25
HappyFabric.deHappyFabric HappyFabric.de
CONTROL PANEL
Digitales Display
Temp Indicator
Set Indicator
Time Indicator
„Increase“
& „Decrease“
Button
„Mode“Button
Technical Specifications
Power: 230 Volt, 700 Watt
Digital timer: 1-999 seconds
Digital temperature control: 96-221 °C
Measurements: Press, closed: approx. 45cm x 32cm x 30cm (length x width x
height;18“ x 12,5“ x 12“ approx.)
Size of heat platen: 30 cm x 23 cm (12“ x 9“ approx.)
Weight: ca. 14,5 kg (32 lb approx.)
Setting the temperature Setting the time Press heats up
Altri manuali per HappyPress
1
Indice
Altri manuali HappyFabric Utensili elettrici
