Harmopool Hydrolyse EC20 Manuale utente

Assembled by:

Swimming pool BVBA

Industrial Road 9

3190 Boortmeerbeek

Belgium

www.harmopool.eu

Contents

Contents...................................................................................................................................2

Incharge

..................................................................................................................................3

Specifications...........................................................................................................................4

Installation...............................................................................................................................4

Installation items .................................................................................................................4

Installation of the water treatment plate ...........................................................................6

Set the parameters of the control unit

................................................................................8

Chlorine control via Rx: set up the Rx set point ....................................................................14

Table 1 ...............................................................................................................................14

Specification of Ph addition...................................................................................................16

Calibration and verification Chlorine /Ph ..............................................................................16

Connecting a flow switch...................................................................................................16

Connecting a level switch ..................................................................................................17

Overview chlorinator.............................................................................................................17

Installation instructions.........................................................................................................19

The use of the chlorinator .....................................................................................................20

Error codes and corresponding chlorinator solutions...........................................................22

Extra : operational use and maintenance of the chlorinator specification...........................23

Maintenance of the peristaltic pump................................................................................26

Warnings............................................................................................................................26

Problem solution for the small steering box.....................................................................27

Incharge

This manual contains all necessary information for installation, troubleshooting and

maintenance. Read the manual thoroughly before opening or using the unit. The

manufacturer of this product will not be held responsible for any injury and/or damage to

the product, if that is the result of improper installation or unnecessary/intended

maintenance. It is essential that you always follow the instructions in this manual.

Installation by qualified personnel is required.

•Only a qualified installer, center, person, or authorized dealer can repair this

product.

•Maintenance and servicing should be performed at the recommended time and

frequency, as indicated in this manual.

•Use only original standard parts. Failure to do so will void your warranty.

Characteristics

•Durable: the materials used are chlorine, acid (sulfuric) and base resistant. They

can withstand prolonged exposure to swimming pool water (even with salt for salt

electrolysis). The dosing devices are not suitable for use with hydrochloric acid (HCl)

•Simple operation: the unit is very convenient to operate. Turn it on and set the

desired pH (acid) or redox value (Chlorine).

•Low cost: the operational cost is very low because the pool water never turns green

when used correctly.

Important elements :

•Incomplete grounding of the elements can have negative consequences on the

measurement results and lead to less good pool water.

•Separate earthing with separate earthing pin for pump, electrolysis is

recommended.

•Correct and proper grounding can avoid many problems.

•Only use city water, preferably no rainwater or well water.

Specifications

ZBSXxxxx ZBSXxxxxxx ZBSXXxxxxP

50 m3 75m3 120m3

pH Control

Chlorine regulation

ZWMX2155

Peristaltic pump

Swimming pool

connection

EC 20 20g/h

Flow switch safety

50mm rubber

Dimension plate

(2x)

38 x 48 cm

Display card

Harmo pool ref ZWMX7010

Relay map

Harmo pool ref ZWMX7011

Installation

Installation items

The factory provides the plate with water treatment equipment without a plug for the

devices. Dit device is elektrisch connected to the salt electrolysis device.

Attention!

○The electrical installation shall be carried out in such a way that:

-The salt electrolysis and acid pump cannot work if the filter pump does not work.

-The salt electrolysis and acid pump can be switched off if the filter pump is working.

-Switching off can always be done with the small on/off buttons on the devices

○Adding the chemicals for the pool should be done downstream from the pool

accessories such as heating, UV lamp, filter etc.

○It is recommended to put the installation of the water treatment unit in bypass

configuration.

○Install the water treatment unit on a solid basis.

○Always keep the product upright. If the product is tilted or laid on the side, the

electrodes cannot measure correctly.

○The product must be installed inside. If you want to do this outdoors, you need to

contact your, supplier.

○The dosing device mag shall not be used with hydrochloric acid (HCl)..

○The electronics (dosing devices) of the appliance must be installed inside. Make sure that

- in case of leak - the water cannot run over the installation.

○Make sure that the acid container is placed OUTSIDE or in a verywell-fertilizedspace.

○Calibrate the pH and Rx electrodes for the first use and then "regular". (At least every

3months).

Installation of the water treatment plate

1. Attach the water treatment unit to a solid wall. Fix both the lower and upper part

of the plate.

2. Insert pH and chlorine electrodes into the electrode holders. Fix the nut with pliers

or wrench to tighten the cap. Failure to do so may result in a leak and is not

covered under warranty.

3Create a separate grounding for your Salt Electrolysis with grounding pen.

4Connect water inlaat and water outlet, so that the water passes the Redox and pH

measuring electrode first and then along the salt electrolysis (or vice versa)..

The preference is for a bypass configuration installation:

5Make the electrical connections in such a way that:

-The salt electrolysis and acid pump cannot work if the filter pump does not work.

-The salt electrolysis and acid pump can be switched off if the filter pump is working.

6Connect the pH and redox measuring heads to the BNC connection to the positions

provided for this purpose:

pH (left) RX (right)

7Start filterpomp.

8Verify that the installation does not leak.

9Stop the filter pump. Remove the elektrodes from the holder and kalibreer pH and redox

electrodes..

Attention!!

(1) If you do not have a bypass configuration, insert two rubber caps (product code:

ZFPX4640) into the electrode bases to prevent water from spraying out of the

electrode bases during calibration.

(2) The electrode calibration procedure may take several minutes. To ensure an

accurate reading, it is important to follow the steps below.

(3) If you do not have a bypass configuration, insert two rubber caps (product code:

ZFPX4640) into the electrode bases to prevent water from spraying from the

electrode bases during calibration.

(4) The electrode calibration procedure may take several minutes. To ensure an

accurate reading, it is important to follow the steps below.

(5) Make sure that the calibration fluids used in the calibration process always match

the values indicated and that the fluids are not contaminated.

Zoutelectrolyse

filter pump

safety fuse with timer

Set the parameters of the control unit

9Calibrate the electrodes

The following steps, you have calibrated the electrodes in no time:

1. Immerse the probes in the calibration fluids for pH (pH 7) and Redox (465-468 mV)

and wait 5 minutes to balance before proceeding with the calibration process.

2. Press the pH and Redox key for 10 seconds (upper and lower key)

As soon as the calibration starts, a screen is activated and shows what you are

calibrating, you can either only calibrate Ph ef only Rx or both at the same time

A timer will stop after 120 seconds and give a notification as to whether the

calibration has succeeded.

Reasons for a failed calibration:

A bad calibration ( recalibrate)

Calibration fluid is contaminated (replace fluid) recalibrate

Measuring probe is broken (too long DRY DRAY) (replace measuring probe) and

recalibrate. Attention : pH probe broken pH value on screen =7

In the case of an unsuccessful

calibration, Hge is the next

notification

wait a moment 033

wait a moment 111

wait a moment

022

wait a moment

022

wait a moment 10

Failed, refer to

manual. Press OK

wait a moment

With a good calibration of Ph and Rx, the screens disappear automatically. After 2

minutes the screens will disappear and you can read the values from the screen. If

the calibration is correct, the values are as follows:

a. pH 7.0 +- 0,1

b. Redox 468 +-10mV

If the values are not within the range as described above, you can press the pH and

Redox keys again to repeat the calibration process.

10 Preparation of the pool water

Make sure that the pH of the pool water is at least between 7.2 and. 8.5 and as close as

possible to 7.4. Make sure that the chlorstabilisator (cyanic acid) content in the pool water

is between 20-40 ppm (20-40 g / 10 m³)

11 Set parameters

Several parameters need to be set. Press the middle key. You will see the following screen:

11.1))Language

You can set a (different) language. Press the middle key again. Then navigate

through the upper or lower key to the languages Français, Castellano, Italiano,

English, Deutsch. You confirm your choice of language by pressing the middle key.

11.2) Dosing mode: proportional continuous ( not for salt electrolysis) Salt time, Salt

Rx(for) salt electrolysis

Press the lower key. The setting "dosing method" is now ticked. Press the middle key to

activate this setting. You can now see that the dosing mode Prop (= proportional) or Cont

(continuous) is selected. Press the middle key again. In the salt electrolysis dosing mode

you can choose between Salt time or Salt Rx.

Attention!

With salt electrolysis you may not use the dosing modes Continuous and Proportional.

Explanation of the dosing method Proportional

With the "Proportional" dosing method, the controller runs continuously through a cycle:

-pH and chlorine content are measured and stored for 40 seconds (no dosing

at this moment)

-The chlorine (if necessary) is dosed for 2 minutes

-The pH-min (if necessary) is dosed for 2 minutes

The closer the pH value approaches the set value, the less the pump will run.

This dosing method (prop) is recommended for working with liquid chlorine and liquid pH

With this dosing method, pH and liquid chlorine are never dosed at the same time.

Explanation of the continuous dosing method:

-The pumps always run when the pH and/or redox setpoint is not reached.

-If you choose this dosing method, the injection point for pH and chlorine must be at

least 2 meters apart. The measurement must be carried out prior to injection.

Explanation of the dosing method salt time:

Explanation of the dosing method Salt (electrolysis) :

Option 1: Salt time

Here one can set a time in hours and minutes with a

maximum of: 23 hours and 59 minutes.

This means that the unit will only function on a time

basis for the creation of chlorine, so the measured

value of Rx will not be taken into account, even if the

Rx setpoint is reached, chlorine will continue to be

created on a time basis.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente