Harol SC900 Manuale utente

INSTALLATION INSTRUCTIONS

SUN PROTECTION

PROTECTION SOLAIRE

SHUTTERS

VOLETS

GATES

PORTES

SURFACE-MOUNTED SCREEN

SC900 - SC910

art.no. 60447

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |2

TABLE OF CONTENTS

1. INTRODUCTION 3

2. GENERAL WARNINGS 3

3. LIST OF TOOLS REQUIRED 4

4. INSTALLATION STEPS 5

4.1. Determine the type of screen 5

4.2. Check the package 5

4.3. Check the product 5

4.4. Check the height and width 5

4.5. The actual assembly in 10 steps 6

4.6. Installation of two or more adjacent screens 14

4.7. Checking the assembly 16

5. ELECTRICAL CONNECTIONS 17

5.1. Connection diagram for a single pole switch 17

5.2. Adjusting the motor - limit switches 18

6. TROUBLESHOOTING AND REPAIRS 20

6.1. The screen will not roll up or down 20

6.2. The motor hums 20

6.3. The motor does not stop in time 20

6.4. Bottom lath is slanted at the top 20

6.5. Bottom lath drops out of the lateral guides 20

6.6. The fabric tension is too slack; the bottom lath sticks

or shudders when the screen is lowered or raised 20

6.7. Folds and waves in the fabric 20

6.8. The direction of the motor’s rotation does not match the arrows on the switch 20

6.9. The fabric does not stop and roll up again 20

6.10. Automatic control does not operate properly 21

6.11. The bottom lath sticks or shudders when the screen is lowered or raised 21

7. REPAIRS 21

8. DISMANTLING AND REMOVAL 21

9. NOTES 22

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |3

1. INTRODUCTION

The SC900 screen is a ﬂat hanging sun screen, which is ﬁtted on top of the window with

a'zipper system' on each side of the fabric. This makes the screen particularly resistant to high

winds and keeps the fabric perfectly in place. In the down position the screen keeps out the

sun's rays, which can cause overheating, while at the same time it gives a view to the outside.

Moreover, this screen oers practical protection against insects, as the space between the

box, the guide rails and the fabric is completely sealed o.

The SC900 can also be ﬁtted with fabrics that are almost fully opaque, making it especially

suitable to black out presentation rooms in oce buildings, laboratories, hospitals etc.

The installation of this sun protection system is explained step by step in these instructions.

The SC910 screen is a ﬂat hanging sun screen with the same properties, but without the

insulation and cover (for the box). It is basically a 'naked' version of the SC900 screen.

Attention!

Open box, standard version without the back covered. This version requires a suitable

ﬁnish to avoid damage to and prevent dirt from settling on the fabric. (possible option =

full support plate instead of brackets)

2. GENERAL WARNINGS

A number of precautions have to be taken for the safe installation, operation and maintenance

of this screen. Please take notice of the following warnings for the safety of everyone concerned!

!These instructions have been drawn up for use by trained installers and therefore are

not suitable for use by amateurs or trainees.

!Please read these instructions carefully before starting the installation.

!Proceed carefully. Ensure that you have a robust footing.

!Make sure there is adequate lighting in the place of assembly. Remove any obstacles

and dirt. Ensure that no other persons other than the installers are present.

Unauthorised persons can get in the way or be at risk during the installation.

!The screen must be kept clearly in view at all times during installation and operation.

Persons in the vicinity may be at risk of injury.

!The installer must comply with the local regulations and standards with regards to

electrical connections.

!Our products must be installed in such a way that all parts remain accessible at all times

for maintenance and repairs. If this is not the case, Harol cannot be held responsible for

any additional costs (e.g. demolition work, repairs to exterior or interior walls) whichmay

result from this.

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |4

Guarantee, terms and conditions

• Harol has endeavoured to design and manufacture the screen in compliance with

the current CE standards. Always check that our version complies with your own

national standards institute.

• No rights can be derived from these instructions whatsoever. Technical modiﬁcations

are reserved without written notiﬁcation.

• For large projects we strongly advise you to ﬁrst ﬁt 1 complete awning before ﬁtting

the remaining awnings. This will help detect any potential faults early on and enable

them to be remedied at the lowest possible cost.

• For our general terms and conditions of sale, please refer to the price list.

• Make sure the screen box can always be opened so the mechanical parts inside can

be reached easily. If these rules are not respected, Harol cannot be held responsible

for the cost of demolition work or any paint work or wallpapering.

Harol NV

Industriepark 3 – 3290 Diest

Belgium

+32 (0)13 38 01 11

+32 (0)13 31 48 03

info@harol.be

www.harol.com

3. LIST OF TOOLS REQUIRED

• Ladder(s)

• Tape measure and pencil

• Cross-slotted screwdrivers

• Spirit level, plumb line or water hose

• Drill

• Set of drills

• Voltage meter or 220 V testing lamp

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |5

4. INSTALLATION STEPS

4.1. Determine the type of screen

Check the type of screen: SC900 (with insulation) or SC910 (without insulation)

4.2. Check the package

Check the package for any damage before removing the complete packaging from around

the box and guide rails.

4.3. Check the product

Check the product: ensure all guide rails and clip proﬁles are included and check if each

guide rail contains a holder with zipper proﬁle.

Also check the bag with accessories. Verify that the screws for securing the support plate,

the clips for the bottom proﬁle and the screws for securing the clip and bottom proﬁles

are there, together with the guarantee card.

4.4. Check the height and width

Check the width of the screen box and measure the window opening.

Verify that both match the desired mounting position.

Also check the height of the guide rails, including the end stop, and make sure they

correspond to the height of the window.

In the following steps logos are used to show the dierence between mounting the SC900

and SC910 screens.

SC900 SC910

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |6

4.5. The actual assembly in 10 steps

Step 1

• Remove the cover and the insulation.

• (SC900) The support plate and base plate are connected. The advantage of thisis

that the base plate does not bend when handling the box. Remove these screws

before mounting the screen!

• (SC910) Unscrew the brackets or support plate (optional) at the bottom, to free the

base plate.

SC900

SC910

SC900

SC900 SC910

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |7

• Then unscrew the two screws at the back that connect to the base plate.

Step 2

• Carefully let the base plate slide from the box.

Please note that this operation must be carried out on both sides of the box

before proceeding to the next step.

SC900

SC910

SC900

SC910

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |8

Step 3

• Centre the base plate on the window and screw it down.

• Make sure the base plate is correctly centred on the window.

• Distance (A) must be the same on both sides.

Tab at the bottom of the base proﬁle forms the abutment with the window.

SC900

SC910

The touch component

for the bottom lath of

the SC910 screen is supplied

separately. This is mounted on

the base plate at a later stage!

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |9

Step 4

• Attach the clip proﬁles with the hole in a downward position.

• First position the upper side of the clip proﬁle against the tab on the bottom side of

the base plate (Fig. 1a-1b).

• Next, drill holes at regular intervals to secure the clip proﬁle and attach it to the window.

• In the bottom pre-drilled hole, the clip proﬁle must be secured together with the end

stop (Fig. 2).

Make sure the clip proﬁles are mounted perpendicular, and check the diagonals

(see 4.6).

There is a hole in the clip proﬁle to secure the end stop (Fig. 2).

Fig. 1a

Fig. 1b

Fig. 2

SC900

SC910

INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910

03/15 |10

Step 5

• Clip both lateral guides - together with the holder with zipper proﬁle - onto the

clipproﬁle.

• No screws are required!

Plan view of the clip proﬁle

and guide rail

SC900

SC910

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Harol Tenda

Harol

Harol VZ710 Manuale utente

Manuali Tenda popolari di altre marche

OZTENT

OZTENT JV SIGNATURE EDITION Manuale utente

GigaTent

GigaTent Summer Chalet Mini Tent Manuale utente

Coleman

Coleman 2000007827 Manuale

ShelterLogic

ShelterLogic 107153 Manuale utente

Outsunny

Outsunny 84C-230 Manuale utente

Napier

Napier SPORTZ COVE 61 Series Manuale utente

EuroTrail

EuroTrail ATLANTIS PRO Manuale utente

Reimo

Reimo Marina Manuale utente

TiiTENT

TiiTENT TB300 Manuale utente

Coleman

Coleman 2000033134 Guida all'installazione

Ozark Trail

Ozark Trail W784.1 Guida rapida

SlingFin

SlingFin CrossBow 2 Manuale utente

Coleman

Coleman 9600-141 Manuale utente

Palram

Palram Arizona 5000 Wave - WINGS Manuale utente

COVERPRO

COVERPRO 56184 Istruzioni per il montaggio

Vango

Vango Zenith 100 Manuale utente

Costway

Costway PATIOJOY OP70818 Manuale utente

Clarke

Clarke PUC 88 Manuale utente